Bradford White RG2DVMH40T6X-264 Bedienungsanleitung

238-37281-00AA REV 5/18

GAS WATER HEATER

WHAT TO DO IF YOU SMELL GAS

•Do not try to light any appliance.

•Do not touch any electrical switch; do not use any

phone in your building.

•Immediately call your gas supplier from a neighbor’s

phone. Follow the gas supplier's instructions.

•If you cannot reach your gas supplier, call the fire

department.

Installation and service must be performed by a qualified

installer, service agency or the gas supplier.

For your family’s comfort, safety and convenience we

recommend water heaters be installed and serviced by a

plumbing professional.

MANUFACTURED HOME (MOBILE HOME)

CLOSED COMBUSTION (DIRECT VENTING)

INSTALLATION AND OPERATING

INSTRUCTION MANUAL

FOR YOUR SAFETY

Do not store or use gasoline or other flammable,

combustible, or corrosive vapors and liquids in the

vicinity of this or any other appliance.

WARNING: If the information in these instructions is

not followed exactly, a fire or explosion may result

causing property damage, personal injury or death.

A Spanish language version of these instructions is available by

contacting the company listed on the rating plate.

La versión espãnola de estas instrucciones se puede obtener al

escribirle a la fábrica cuyo nombre aparece en la placa de

especificaciones.

CONGRATULATIONS!

You have just purchased one of the finest water heaters

on the market today!

This installation, operation and instruction manual will

explain in detail the installation and maintenance of your

new Mobile Home Water Heater. We strongly recommend

that you contact a plumbing professional for the

installation of this water heater.

We require that you carefully read this manual, as well as

the enclosed warranty, and refer to it when questions

arise. If you have any specific questions concerning

your warranty, please consult the plumbing professional

from whom your water heater was purchased. For your

records we recommend that you write the model, serial

number and installation date of your water heater in the

maintenance section in the back of this manual.

This manual should be kept with the water heater.

TABLE OF CONTENTS

Page

GENERAL INFORMATION .............................................................................4

INSTALLATION...............................................................................................5

Locating the Water Heater .......................................................................5

Minimum Clearances................................................................................8

Drain Pan Installation ...............................................................................9

Combustion Air Supply...........................................................................10

Venting....................................................................................................11

Water Connections.................................................................................12

Gas Connections....................................................................................15

Gas Conversion Instructions..................................................................16

GENERAL OPERATION ...............................................................................20

Lighting and Shutdown Instructions .......................................................21

Thermostat Adjustment ..........................................................................22

Burner Flame Check ..............................................................................24

MAINTENANCE.............................................................................................24

TYPICAL INSTALLATION.............................................................................27

PARTS LIST ..................................................................................................28

GENERAL INFORMATION

This water heater must be installed in accordance with The Federal

Manufactured Home Construction And Safety Standard (H.U.D. Title 24, Part

3280.707d2) or CAN/CSA Z240 MH series, mobile home. In the absence of

such a standard, the water heater should be installed in accordance with the

Standard For Mobile Homes (ANSI/NFPA NO. 501-B1977).

The warranty for this water heater is in effect only when the water heater is

installed, adjusted, and operated in accordance with these Installation and

Operating Instructions. The manufacturer will not be liable for any damage

resulting from alteration and/or failure to comply with these instructions.

This water heater is of the closed combustion type (direct venting) where all the

combustion air is supplied from the outdoors through the air intake and all

combusted gas products are vented directly to the outside by means of the roof

jack. No draft diverter (vent hood) is required for this water heater.

INTERTEK has tested a representative sample of this water heater design for

its safety of operation. The ETL listing of this water heater includes the field

installation of the following components: roof jack, air intake tube, and heater

tie down materials. These components for field installation may have been

shipped with this heater and must be installed according to these instructions

(see figure 1). No other components are approved for use with this water

heater.

This water heater has been designed and certified for the purpose of heating

potable water. The installation and use of this water heater for any purpose

other than the heating of potable water may cause damage to the water heater,

create a hazardous condition, and nullify the warranty.

Do not use this appliance if any external part to the tank has been submerged

in water. You should contact a qualified service technician to inspect the

appliance and to replace any part of the control system including the

combination gas control which has been submerged in water. See the Gas

Connections section of this manual before servicing or replacing a water heater

that has had any external part to the tank submerged in water.

CAUTION

Incorrect operation of this appliance may create a hazard to life and

property and will nullify the warranty.

WARNING

Prior to connecting the gas supply line to a gas fired water heater,

ensure that the gas supply line does not have moisture/water or

dirt/scale inside the gas line. Commonly this check is done at the

lowest point in the gas distribution system prior to gas burning

appliances.

General Information continued-

This water heater has been manufactured for operation at altitudes from sea

level to 2000 feet (610m) (unless otherwise specified on the water heater).

For use of this appliance at an elevation greater than 2000 feet (610m), contact

the dealer or manufacturer listed on the rating plate for information on any

necessary modification. Uncorrected operation of this appliance may create a

hazard to life and property.

Make sure to check the rating plate and combination gas control on the water

heater to be certain that the type of gas being supplied corresponds with the

marking on the rating plate and combination gas control.

A sacrificial anode(s) is used to extend tank life. Removal of any anode, except

for inspection and/or replacement, will nullify the warranty. In areas where

water is unusually active, an odor may occur at the hot water faucet due to a

reaction between the sacrificial anode and impurities in the water. If this should

happen, an alternative anode(s) may be purchased from the supplier that

installed this water heater. This will minimize the odor while protecting the tank.

Additionally, the water heater should be flushed with appropriate dissolvers to

eliminate any bacteria.

INSTALLATION

Locating the Water Heater

This water heater MUST NOT be installed in any location where gasoline or

flammable vapors are likely to be present, unless the installation is such to

eliminate the probable ignition of gasoline or flammable vapors.

The location of this water heater is of the utmost importance. Before installing this

water heater, read the Installation section of these instructions. DO NOT locate the

water heater where water lines could be subjected to freezing temperatures.

Make sure the cold water pipes are not located directly above the gas control

so that condensate during humid weather does not drip on the controls.

IMPORTANT

Before proceeding, please inspect the water heater and components for

possible damage. DO NOT install any damaged components. If damage

is evident then please contact the supplier where the water heater was

purchased or the manufacturer listed on the rating plate for replacement

parts.

DANGER

Do not store or use gasoline or other flammable, combustible, or

corrosive vapors and liquids in the vicinity of this or any other

appliance.

WARNING

This product contains one or more chemicals known to the State of

California to cause cancer, birth defects, or reproductive harm.

Installation (Locating The Water Heater) continued-

Water heater corrosion and component failure can be caused by the heating

and breakdown of airborne chemical vapors. Examples of some typical

compounds that are potentially corrosive are: spray can propellants, cleaning

solvents, refrigerator and air conditioning refrigerants, swimming pool

chemicals, calcium and sodium chloride, waxes and process chemicals. These

materials are corrosive at very low concentration levels with little or no odor to

reveal their presence. NOTE: DAMAGE TO THE WATER HEATER CAUSED

BY EXPOSURE TO CORROSIVE VAPORS IS NOT COVERED BY THE

WARRANTY. DO NOT OPERATE THE WATER HEATER IF EXPOSURE

HAS OR WILL OCCUR. DO NOT STORE ANY POTENTIALLY CORROSIVE

COMPOUNDS IN THE VICINITY OF THE WATER HEATER.

For exact venting specifications, please consult the Venting section of these

Installation and Operating Instructions. It is recommended that a minimum

clearance of 4 inches (10.2 cm) be provided on the side of the water heater for

servicing and maintenance of the combination temperature and pressure relief

valve.

WARNING

Water heaters are heat producing appliances. To avoid damage or

injury there must be no materials stored against the water heater or

vent-air intake system and proper care must be taken to avoid

unnecessary contact (especially by children) with the water heater and

vent-air intake components. UNDER NO CIRCUMSTANCES MAY

FLAMMABLE MATERIALS, SUCH AS GASOLINE OR PAINT

THINNER BE USED OR STORED IN THE VICINITY OF THIS WATER

HEATER, VENT-AIR INTAKE SYSTEM OR IN ANY LOCATION FROM

WHICH FUMES COULD REACH THE WATER HEATER OR VENT-

AIR INTAKE SYSTEM.

WARNING

DO NOT ATTEMPT TO LIGHT ANY GAS APPLIANCE IF YOU ARE

NOT CERTAIN OF THE FOLLOWING:

• Liquefied petroleum gases/propane gas and natural gas have an

odorant added by the gas supplier that aids in detection of the gas.

• Most people recognize this odor as a “sulfur” or “rotten egg” smell.

• Other conditions, such as “odorant fade” can cause the odorant to

diminish in intensity, or “fade”, and not be as readily detectable.

• If you have a diminished sense of smell, or are in any way unsure of

the presence of gas, immediately contact your gas supplier from a

neighbor’s telephone.

• Gas detectors are available. Contact your gas supplier or plumbing

professional for more information.

Installation (Locating The Water Heater) continued-

This water heater MUST be installed indoors out of the wind and weather.

This water heater must be located in an area where leakage of the tank, water

line connections, or the combination temperature and pressure relief valve will

not result in damage to the area adjacent to the water heater or to lower floors

of the structure. When such locations cannot be avoided, a suitable drain pan

must be installed under the water heater (Refer to drain pan installation section

for more information.). The drain pan must have a minimum length and width

of at least 4 in. (10.2 cm) greater than the diameter of the water heater and

must not restrict proper combustion air flow to the water heater. The drain pan,

as described above, can be purchased from your plumbing professional. The

drain pan must be piped to an adequate drain. The piping must be at least 3/4

inch (1.9 cm) in diameter and pitched for proper drainage.

To comply with NSF requirements this water heater is to be:

a) Sealed to the floor with sealant, in a smooth and easily cleanable way,

b) Installed with an optional leg kit that includes legs and/or extensions

that provide a minimum clearance of 6” beneath the water heater.

Note: For California installation this water heater must be braced,

anchored, or strapped to avoid falling or moving during an earthquake.

See instructions for correct installation procedures. Instructions may be

obtained from the DSA Headquarters Office, 1102 Q Street, Suite 5100,

Sacramento, CA 95811.

WARNING

Liquefied petroleum gases/propane gases are heavier than air and will

remain at floor level if there is a leak. Basements, crawl spaces, closets

and areas below ground level will serve as pockets for accumulation of

leaking gas. Before lighting, smell all around the appliance area for gas.

Be sure to smell next to the floor.

IF YOU SMELL GAS:

• Do not try to light any appliance.

• Do not touch any electric switch; do not use any telephone in your

building.

• Immediately call your gas supplier from a neighbor’s telephone.

Follow the gas supplier’s instructions.

• If you cannot reach your gas supplier, call the fire department.

DO NOT OPERATE APPLIANCE UNTIL LEAKAGE IS CORRECTED!

Minimum Clearances

This installation must allow access to the front of the water heater and

adequate clearance must be provided for servicing and operating this water

heater. The water heater may be installed on either a combustible or non-

combustible floor. If the water heater is to be installed directly on carpeting, it

must be installed on top of a metal or wood panel (or equivalent) extending

beyond the full width and depth of the appliance by at least 3 inches (7.6 cm) in

any direction or, if the appliance is to be installed in an alcove or closet, the

entire floor must be covered by the panel.

Figure 1

WARNING

Failure to adhere to these installation and operating instructions

may create a hazard to life and property and will nullify the

warranty.

IMPORTANT

The flow of combustion and ventilating air must not be obstructed.

Minimum Clearances From

Combustible Materials

A 0” (0cm)

B 0” (0cm)

C 3” (7.62cm)

D 78” (1.98mm)

VENT----

Drain Pan Installation

for non-flammable vapor ignition resistant manufactured home water heaters

1. This section is intended for use with non-flammable vapor ignition resistant

manufactured home water heaters that will be installed in an application where

a drain pan is required.

2. After hole is cut in floor and underside sheathing, and before the water heater

is installed, prepare drain pan.

3. Locate and cut a 3-1/2” diameter hole in drain pan at 4-1/2” from center (see

Figure 2). This hole will be located at the front of the water heater upon final

installation.

4. Align drain pan hole with hole cut in floor and underside sheathing for air

intake.

5. Apply 4” diameter circle of silicone around bottom of air intake plate and

screws used to secure air intake to floor for proper water tight sealing (see

Figure 3).

6. Continue proper installation per this installation and operation manual and the

roof jack & air intake installation instructions provided with the roof jack kit. Be

sure to apply silicone around screws used to secure the water heater to the

floor through the drain pan for proper water tight sealing.

CAUTION

Silicone has a strong odor and should have adequate ventilation until

cured. Refer to the manufacturer’s instructions for adequate drying time.

Figure 2

Figure 3

Figure 4

Combustion Air Supply

All combustion air must be supplied from outdoors by one of the following

installation methods and as illustrated in Figure 5. The flow of combustion and

ventilating air must not be obstructed. Adequate air must be supplied for

combustion and ventilation. An insufficient supply of air will cause recirculation

of combustion products resulting in air contamination that may be hazardous to

life. Such a condition often will result in a yellow, luminous burner flame,

causing carboning or sooting of the combustion chamber, burners and flue

tubes with possible damage to the heater.

AIR INTAKE INSTALLATION - 3” (7.6cm) diameter telescoping air intake and

leg enclosure are required to supply fresh air to the water heater. Note: When

a mobile home is tightly skirted, an air inlet opening in the skirting must

be provided. The opening must have a minimum free area of at least 9 in2

(22.9cm2). If the opening is screened or covered with a louver, the total

free area must be at least 9 in2(22.9cm2). The following steps must be

followed for proper installation of these air supply components: (Refer to Figure

5).

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Bradford White Boiler Handbücher

Bradford White

Bradford White ECO-DEFENDER U130T*FRN Bedienungsanleitung

Bradford White

Bradford White 216-B Bedienungsanleitung

Bradford White

Bradford White 103-B Bedienungsanleitung

Bradford White

Bradford White URG2PV75H6N-475-264 Bedienungsanleitung

Bradford White

Bradford White Copper Brute II Bedienungsanleitung

Bradford White

Bradford White BRADFORD WHITE EVERHOT TG-150I-N(X) Service-Handbuch

Bradford White

Bradford White M-1-40S6BN Beilage

Bradford White

Bradford White UPV Series Bedienungsanleitung

Bradford White

Bradford White 355-B Bedienungsanleitung

Bradford White

Bradford White Condensing PV Series Bedienungsanleitung

Bradford White

Bradford White 203-B Bedienungsanleitung

Bradford White

Bradford White Everhot IGE-199R Series Beilage

Bradford White

Bradford White Powered Direct Vent Series Bedienungsanleitung

Bradford White

Bradford White RE2H50R10-1NCWW Originalbetriebsanleitung

Bradford White

Bradford White Combi2 "CDW2" Series Anwendungshandbuch

Bradford White

Bradford White PDX1-40S6FBN Beilage

Bradford White

Bradford White M-I-WH6U6SS Bedienungsanleitung

Bradford White

Bradford White S-SW2-60R6DS Bedienungsanleitung

Bradford White

Bradford White Combi2 TTW C-DW2-TW50T10FBN Bedienungsanleitung

Bradford White

Bradford White UCG100H199 Bedienungsanleitung

Bradford White

Bradford White LD-12UT3-1 Bedienungsanleitung

Bradford White

Bradford White 105-B Bedienungsanleitung

Bradford White

Bradford White UDH Series Bedienungsanleitung

Bradford White

Bradford White 100T399-SOLA Betriebsanleitung

Beliebte Boiler Handbücher anderer Marken

Kenmore

Kenmore 153.582400 Bedienungsanleitung

STIEBEL ELTRON

STIEBEL ELTRON Eltronom SHU 5 S Bedienungsanleitung

clage

clage E-Mini Series Bedienungsanleitung

Toyotomi

Toyotomi Oil Miser OM-180 Bedienungsanleitung

Eccotemp

Eccotemp 40-H Bedienungsanleitung

Dimplex

Dimplex ECSd125-580 Leitfaden

Dux

Dux 32FCR6N Bedienungsanleitung

Noritz

Noritz N-132M Gebrauchsanweisung

TESY

TESY GCV7/4S 10047 Technisches Datenblatt

A.O. Smith

A.O. Smith Gphe 50 Bedienungsanleitung

Toyotomi

Toyotomi Oil Miser OM-148 (Type D) Fehlerbehebungshandbuch

Koryo

Koryo KWHZF15Y Bedienungsanleitung

Pentair

Pentair PSC-14-4-02 Bedienungsanleitung

GE 40M06AAG Montageanleitung

Thermor

Thermor AEROMAX SPLIT 2 Bedienungsanleitung

American Hometec

American Hometec AHQ-B03X Bedienungsanleitung

PVI

PVI MAXIM Bedienungsanleitung

Sunerg Solar Energy

Sunerg Solar Energy Calor Top 200D Betriebsanleitung