Bristan FLT 3HBAS C Bedienungsanleitung

Please keep this booklet for future

reference.

Installer, when you have read these

instructions please ensure you leave them

with the user.

Installation Instructions

Flute Tap Range

Models covered:

FLT 3HBAS C, FLT 3HBF C,

FLT WMBAS C, FLTWMBF C,

FLT BS C

Contents

Thank you for choosing Bristan, the UK’s leading taps and showers expert.

We have designed this product with your enjoyment in mind. To ensure that it works

to its full potential, it needs to be ﬁtted correctly. These ﬁtting instructions have been

created to give you all of the information you need and, if you need any further help,

please do not hesitate to contact us.

Important Safety Information................................................... 3

General Information ................................................................. 4

Speciﬁcations ........................................................................... 4

Dimensions............................................................................... 5-7

Installation Requirements ....................................................... 8

Installation................................................................................ 9-11

3 Hole Basin Mixer / Bath Filler .............................................. 9

Wall Mounted Basin Mixer / Bath Filler .................................. 10

Bath Spout ................................................................................ 11

Maintenance ............................................................................. 12

Troubleshooting........................................................................ 13

Guarantee ................................................................................. 14-15

Need help? Give us a call on 0844 701 6273 and speak to one of our trained advisers.

Important Safety Information

•Please read these instructions thoroughly and retain for future use.

•All products manufactured and supplied by Bristan are safe provided they are

installed, used correctly and receive regular maintenance in accordance with these

instructions.

•If you are in any doubt about your ability to install this product safely you must

employ the services of an experienced qualiﬁed plumber.

•This ﬁtting needs to be installed in accordance with, and meet the requirements of the

Water Supply (Water Fittings) Regulations 1999 and Scottish Byelaws 2004.

•Remove all packaging and check the ﬁtting for damage before starting installation.

•Warning: Before starting any installation please consider the following: before

drilling into walls, check that there are no hidden electrical wires, cables or water

supply pipes. This can be checked with the aid of an electronic detector.

•If power tools are used do not forget to: - Wear eye protection

- Unplug equipment after use

•Important: Remember to turn off the mains water supply before connecting to any

existing pipe work. Fitting isolating valves to the inlet feeds is recommended for ease

of maintenance.

•Warning: Before installing the new ﬁtting it is essential that you thoroughly ﬂush

through the pipework in order to remove any remaining swarf, solder, etc.

Failure to carry out this procedure could cause problems or damage to the workings of

the ﬁtting.

•Take care when handling the ‘ﬂexible connecting pipes’, do not bend, twist or crush

them. Only tighten the pipes by hand.

• This product must not be modiﬁed in any way as this will invalidate the guarantee.

Need help? Give us a call on 0844 701 6273 and speak to one of our trained advisers.

General Information

This product has been tested to the Water Regulations Advisory Scheme (WRAS) and

satisﬁes the requirements of the Water Supply (Water Fittings) Regulations 1999 and

current bylaws. For full Installation Requirements & Notes (IRN) please visit

www.wras.co.uk/directory.

Designed to comply with BS EN 200 for combination taps to be used within systems

designed to BS 6700.

BS 6700 recommends the temperature of stored water should never exceed 65°C.

A stored water temperature of 60°C is considered sufﬁcient to meet all normal

requirements and will minimise the build up of lime scale in hard water areas.

If installing this product on a low pressure (tank fed) system please see speciﬁcation

table below to determine the minimum distance required from underside of the cold

water tank to the outlet.

These taps and mixers should be installed in compliance with the Water Regulations.

Where the supplies are unbalanced, i.e. Hot water from cylinder tank / cold from the

mains, approved check valves must be ﬁtted in the supply pipes.

For further details contact your Local Water Authority.

Speciﬁcations

Product Code

Working pressure

Inlet

Minimum distance

from cold water tank

to outlet (metres)

Min Max

FLT 3HBAS C 0.2 5.0 15mm Compression Threaded Tail 2

FLT 3HBF C 0.3 5.0 3/4" BSP Threaded Tail 3

FLT WMBAS C 0.2 5.0 15mm Compression 2

FLT WMBF C 1.0 5.0 15mm Compression 10

FLT BS C 0.1 5.0 1/2" BSP Threaded Tail 1

Maximum static pressure- 10.0 bar

Need help? Give us a call on 0844 701 6273 and speak to one of our trained advisers.

Dimensions

Dimensions are nominal and in millimetres.

Dimensions

Need help? Give us a call on 0844 701 6273 and speak to one of our trained advisers.

3 Hole Basin Mixer

3 Hole Bath Filler

156

137

105

115

120

117

144

65 116

154

176

Dimensions Cont.

Bath Spout

Dimensions are nominal and in millimetres.

Need help? Give us a call on 0844 701 6273 and speak to one of our trained advisers.

Wall Mounted Basin Mixer

223

210

110

55-70

200

Dimensions Cont.

Dimensions are nominal and in millimetres.

Need help? Give us a call on 0844 701 6273 and speak to one of our trained advisers.

Wall Mounted Bath Filler

203

220

120

55-

Installation Requirements

Flexible Connecting Pipes

Care must be taken when connecting the ﬂexible connection pipes to the household

pipework to ensure they do not bend sharply and kink or twist.

See below for recommended ways to ﬁt the ﬂexible connecting pipes.

Slight

bend

90°

Angle

Kink Curved

round

Twists

Important: Failure to follow these guidelines may result in poor performance and damage

to the ﬂexible connecting pipes.

Important: Full access must be made available on installation for future maintenance/

servicing purposes.

System Requirements:

Gravity fed hot & cold (Equal pressures)

Gravity fed hot & cold (Differential pressure, maximum ratio 5:1)

Unvented systems

Instantaneous water heater (Combination boiler)

Need help? Give us a call on 0844 701 6273 and speak to one of our trained advisers.

Installation

1. With the backnut, metal and rubber

washers ﬁtted to the side body threaded

tail, feed the side body through the hole

from underneath the basin/ bath.

2. Screw the shroud onto the treaded tail

and tighten the backnut underneath onto

the bottom of the basin/ bath and replace

the handle, tighten the grub screw and

push ﬁt the cap.

3. Fit the spout to the basin/ bath

tightening the backnut.

4. Attach the T- joint assembly to the bot-

tom of the spout and connect to the side

bodies (hot on the left, cold on the right

when viewed from the front), by using ﬂexi

tails supplied.

5. Connect the hot and cold water

supplies to the side bodies (hot to the left,

cold on the right hand side), fully open

both valves, letting the water run for a few

minutes to ﬂush the system.

6. Fit the clicker waste (basin mixer only)

ensuring the rubber washer is ﬁtted

between the basin and the waste.

Place the other rubber washer

under the basin and secure in place by

tightening the backnut. In order to ﬁll the

basin, the button in the middle of the

waste needs to be pressed down.

To release the water, press the button

again.

7. Check all joints and connections

for leaks.

3 Hole Basin Mixer/ Bath Filler

Need help? Give us a call on 0844 701 6273 and speak to one of our trained advisers.

Installation Cont.

Wall Mounted Basin Mixer / Bath Filler

1. Decide on the ﬁnal position of the basin mixer/

bath ﬁller. Install suitable battons onto the wall

cavity if required.

2. Plumb the hot and cold water supply pipes to

the required position ensuring the hot is on the

left and cold is on the right when viewed from the

front.

3. Secure body using the screws and wall plugs

supplied.

4. Attach pipework to the hot and cold inlets (hot

on the left and cold on the right when viewed from

the front) ensuring the olive is ﬁtted to the copper

pipe work. Tighten the compression nut to secure

pipework and create a water tight seal.

Note: Before ﬁnishing the wall surface turn on the

water supplies to check for any leaking

connections.

5. Finish the wall surface.

Note, it is important sufﬁcient thread is left

exposed to allow the spout to connect.

6. Push the plate onto the body upto the wall

surface.

7. Fit the spout and tighten the grub screws to

secure in position.

8. Screw the shroud onto the valve and secure

by tightening the grub screw. Screw the locking

shroud onto the shroud.

9. Push the handle onto the valve shroud and

tighten the grub screws.

10. Turn on both water supplies and operate the

handle letting the water ﬂow for a few minutes to

ﬂush the system.

Need help? Give us a call on 0844 701 6273 and speak to one of our trained advisers.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Bristan Küchen- und Badezimmerausstattung Handbücher

Bristan

Bristan Oval Tap Series Verdrahtungsschema

Bristan

Bristan AR SNKPURE C Bedienungsanleitung

Bristan

Bristan Java Bedienungsanleitung

Bristan

Bristan Java Series Verdrahtungsschema

Bristan

Bristan Gummers H64WMT Montageanleitung

Bristan

Bristan Prism PM 3HWMBAS C Bedienungsanleitung

Bristan

Bristan W SNK5C Verdrahtungsschema

Bristan

Bristan Nero NR BASNW C Verdrahtungsschema

Bristan

Bristan Pear PEA PULLSNK C Verdrahtungsschema

Bristan

Bristan FH TDRD01 C Bedienungsanleitung

Bristan

Bristan Z2 1/2 C Verdrahtungsschema

Bristan

Bristan Acute AE 1/2 C Bedienungsanleitung

Bristan

Bristan Soft Touch Series Bedienungsanleitung

Bristan

Bristan Regency R2 SHXAR C Montageanleitung

Bristan

Bristan MINI2 TS1203 CL C Montageanleitung

Bristan

Bristan QD 1/2 C Verdrahtungsschema

Bristan

Bristan Artisan Evo Montageanleitung

Bristan

Bristan AR THBSM C Bedienungsanleitung

Bristan

Bristan W BASIN04 C Bedienungsanleitung

Bristan

Bristan Claret CLR BASNW C/WHT Montageanleitung

Bristan

Bristan GLL RAPSNK3 C Montageanleitung

Bristan

Bristan CAS BAS C Bedienungsanleitung

Bristan

Bristan IRSD1-CP Montageanleitung

Bristan

Bristan Liquorice LQR PROSNK C Verdrahtungsschema

Beliebte Küchen- und Badezimmerausstattung Handbücher anderer Marken

Grohe

Grohe BRIDGEFORD 33 870 Bedienungsanleitung

Hans Grohe

Hans Grohe Zenio Metro 31811000 Bedienungsanleitung

Gröne

Gröne Zedra 32 555 Bedienungsanleitung

Transform

Transform QL045 Bedienungsanleitung

Sanela

Sanela SLU 09PTB Bedienungsanleitung

Glacier bay

Glacier bay FP4A0052BNV Montageanleitung

Lefroy Brooks

Lefroy Brooks C1-1400 Montageanleitung

Grohe

Grohe Rapido E Bedienungsanleitung

Danze

Danze D302455 Bedienungsanleitung

Waterworks

Waterworks CEKM30 Merkblatt

Helvex

Helvex Omega TV-298 Bedienungsanleitung

Tribata.

Tribata. GEORGIAN G5393 Bedienungsanleitung

Alpha Bidet

Alpha Bidet Alpha One Bedienungsanleitung

InSinkErator

InSinkErator H/HC3300 Installationshandbuch

Clou

Clou Xo type 1 Bedienungsanleitung

Kohler

Kohler Contra 26448T-4 Bedienungsanleitung

Grohe

Grohe Bridgeford 20 158 Bedienungsanleitung

Hans Grohe

Hans Grohe Croma Select S 180 Showerpipe EcoSmart... Bedienungsanleitung