Bristan Cadet Verdrahtungsschema

Installation Instructions & User Gide

Cadet Tap Range

Installation Instructions & User Guide

IMPORTANT: Please keep these instructions for future reference and request of replacementparts

Thank you for choosing Bristan, the UK’s leading showers and taps expert.

We have designed this product with your enjoyment in mind. To ensure that it

works to its full potential, it needs to be fitted correctly. These fitting instructions

have been created to give you all of the information you need and, if you need

any further help, please do not hesitate to give us a call on 0330 026 6273.

Important Safety Information 03

General Specifications 03

Installation 04-06

Maintenance 07-09

Troubleshooting 10

Guarantee 11

Contents

Important Safety Information

•Please read these instructions thoroughly and retain for future use.

• All products manufactured and supplied by Bristan are safe provided they are

installed correctly, used correctly and receive regular maintenance in accordance with

these instructions.

•If you are in any doubt about your ability to install this product safely you

must employ the services of an experienced qualified plumber.

• Remove all packaging and check the components for damage before starting

installation.

•Before starting any installation please consider the following:

•Prior to drilling into walls, check that there are no hidden electrical wires,

cables or water supply pipes. This can be checked with the aid of an

electronic detector.

•If power tools are used do not forget to: - Wear eye protection

- Unplug equipment after use

• This product must not be modified in any way as this will invalidate the guarantee.

•These fittings need to be installed in accordance with and meet the requirements of

the Water Supply (Water Fittings) Regulations 1999 and Scottish Byelaws 2004.

General Specifications

Operating pressure range (bar) Min Max

CAD ½ C 0.2 5.0

CAD ¾ C 0.2 5.0

CAD BAS C 0.2 5.0

CAD BF C 0.2 5.0

CAD BSM C 0.2 5.0

Maximum static pressure –10.0 bar

NOTE:- Nominally equal (balanced) inlet supply pressures are recommended for

optimum performance of mixer taps.

Designed to comply with BS EN 200 for single taps / combination taps for water

systems of type 1 and 2 general technical specifications; and to be used within

systems designed to BS 6700. BS 6700 recommends the temperature of stored

water should never exceed 65°C. A stored water temperature of 60°C is considered

sufficient to meet all nominal requirements and will minimise the build up of lime

scale in hard water areas.

Installation

Basin & Bath Taps

Identify all components are

present prior to staring the

installation.

1. Slide the plinth onto the

threaded tail and fit the tap

body to the basin / bath.

2. Slide the washer onto the

threaded tail and secure the

tap to the basin / bath by

tightening the backnut. A

suitable spanner may be

required to fully tighten the

backnut,

3. Connect the hot and cold

water supplies to the

threaded tails using either a

½” or ¾” BSP connector (not

supplied).

4. Turn on water supplies and

turn both taps to the on

position, letting the water

flow for a few minutes.

5. Check all joints and

connections for any leaks.

Washer

Backnut

Basin Mixer

Installation cont.

Identify all components are present prior to

staring the installation.

1. Screw the flexi tails into the bottom of

the mixer body by hand only (DO NOT

OVERTIGHTEN).

2. Place the plinth over the hole in the

basin and feed the flexi tails through the

hole, ensuring the washer is fitted

between the mixer body and the basin.

3. Screw the fixing rods into the bottom of

the mixer body.

4. Slide ‘C’ shaped rubber washer and ‘C’

shaped metal washer onto the fixing

rods up to the underside of the basin.

5. To secure the mixer in place tighten the

fixing nuts onto the fixing rods until they

are fully tightened against the ‘C’ shaped

metal washer. The fixing nuts can be

tightened with a suitable spanner.

6. Connect the flexi tails to the hot and

cold water supplies.

7. Turn on water supplies, lift the mixer

handle upwards and operate in both

directions, letting the water flow for a

few minutes.

8. Fit the clicker waste ensuring a rubber

washer is fitted between the basin and

the waste. Use a pure silicon sealant

where necessary. Place the other rubber

washer under the basin and secure by

tightening the backnut, in order to fill

the basin, the button in the middle of

the waste needs to be pressed down. To

release the water, press the button

again.

9. Check all joints and connections for any

leaks.

Flexi Tails

‘C’ Shaped

Rubber

Washer

‘C’ Shaped

Metal

Washer

Fixing

Rods

Fixing Nuts

Installation cont.

Bath Filler and Bath Shower Mixer

Identify all components are present prior to

staring the installation.

1. Fit the mixer body to the bath ensuring

that the foam gasket is fitted between

the mixer body and the bath.

2. Secure the mixer to the bath using the

washer and metal backnut below the

bath. Tighten the backnut onto the

threaded tails. A suitable spanner may

be required to fully tighten the backnut.

3. Connect the hot and cold water supplies

to the threaded tails using a ¾” BSP

connector (not supplied).

4. Bath Shower Mixer only - fit the shower

hose to the hose outlet using the small

sealing washer, and the handset to the

hose using the small washer.

Prior the drilling into walls, check

there no hidden electrical wires,

cables or water supply pipes with the aid of

an electronic detector.

If you use power tools do not forget to:

•Wear eye protection

•Unplug equipment after use

5. Fit the wall bracket (not shown) to the

wall using the fixings supplied, ensuring

the handset and hose reaches it.

To switch from bath to shower mode,

pull the diverter knob up, to revert back

to bath filling mode push the diverter

knob back down.

6. Turn on water supplies and turn both

handles into the on position, letting the

water flow for a few minutes. Check all

joins and connections for any leaks.

Washer

Backnut

Shower

Hose

Sealing

Washer

General Cleaning

Your fitting has a high quality finish

and should be treated with care to

preserve the visible surfaces. All

finishes will wear if not cleaned

correctly. The only safe way to clean

your product is to wipe with a soft

damp cloth. Stains can be removed

using washing up liquid. All

bathroom cleaning products

(powders and liquids) will damage

the surface of your fitting, even the

non-scratch cleaners.

Note: Never use abrasive

detergents or disinfectants or those

containing alcohol, hydrochloric

acid or phosphoric acid.

We advise that your fitting is regularly

serviced in hard water areas to maintain

optimum performance.

Cleaning the Showerhead:

CAD BSM C

Your Bristan showerhead has rub-clean

nozzles for easy cleaning. Simply rub

your fingers across the rubber spray

jets regularly and before you turn the

shower on to remove any scale or

debris.

Maintenance

The hardness of the water in your area

will determine how often you should

clean your showerhead. Build up of scale

in particularly hard water areas

combined with constant use means you

may need to clean your showerhead

once a week. To ensure continued

performance the showerhead needs to

be regularly descaled.

Tip: If the showerhead is heavily scaled

or has not be maintained for a long

period of time a solution of hot water

and white vinegar may be needed to

clear the scale.

Mix a 50/50 solution and rub the

nozzles thoroughly with the solution

making sure the solution gets into all of

the nozzles.

Wash off the solution with clean water.

Maintenance cont.

Cleaning the Valves (CAD ½ C, CAD 3/4 C, CAD BF C, CAD BSM C):

If your fitting begins to leak the follow should

be carried out:

Isolate both hot and cold water supplies to

the tap by either:

•Turning the water supply off at the

mains stopcock or

•Turning off the isolation valves to the

tap

1. Prise out the handle cap, loosen the

grub screw and pull the handle

upwards.

2. Remove the spline adaptor.

3. Lift out the valve and clean thoroughly.

Be sure to check and clean out the

seating within the mixer body. If

necessary replace the valve.

4. Please visit www.bristan.com and

search for your product code in order

to find spare parts for this product.

5. Place the valve back into the tap body

and tighten the valve fully using a

suitable spanner.

6. Replace the spline adaptor and push

the handle onto the valve. Tighten the

grub screw and push fit the cap.

7. Turn on water supply and check for

leaks.

8. Contact our helpline if problem

persists.

Handle

Spline

adaptor

Valve

Tap

Body

Grub Screw

Cap

If your fitting begins to leak the following

should be carried out;

Isolate both hot and cold water supplies to

the tap by either:

•Turning the water supply off at the mains

stopcock or

•Turning off the isolation valves to the tap.

1. Prise out the handle cap, loosen the

grub screw and pull the handle upwards.

2. Unscrew the shroud and cartridge

retaining nut and pull the cartridge out

from the body.

3. Clean the cartridge thoroughly under

cold water to remove any build up of

limescale or debris. If necessary replace

the cartridge

4. Please visit www.bristan.com and

search for your product code in order

to find spare parts for this product.

5. Replace the cartridge into the body and

tighten the retaining nut to secure in

place.

6. Screw the shroud onto the retaining nut

and push the handle onto the cartridge.

Tighten the grub screw and push fit the

cap.

7. Turn on water supply and check for

leaks.

8. Contact our helpline if problem persists.

Maintenance cont.

Cleaning the Cartridge (CAD BAS C):

Handle

Shroud

Cartridge

Retaining

Nut

Cartridge

Tap

Body

Grub Screw

Cap

Symptom Cause Remedy

No flow or poor flow

rate.

Partially closed stop or

service valve in water supply

pipework to the tap.

Open stop or service valve.

Head of water is below the

minimum distance required.

Refer to the Specification

section for minimum

pressures required.

Possible airlock / blockage in

supply pipework

Remove water supplies from

the fitting and flush the

system to remove any

airlocks / debris.

Cartridge / Valve not

opening fully.

Service fitting. Refer to

maintenance section on

pages 8-9.

Water dripping for a

few seconds after

the tap has been

turned off.

This is caused by ‘capillary

action’ and residual water in

the spout being siphoned

out.

This should only last for a

couple of seconds, and is

normal after use.

Constant dripping /

leaking when the

tap is not in use.

Cartridge / valve not fully

shutting off.

Service fitting and replace

cartridge/ valve. Refer to

maintenance section on

pages 8-9.

Fitting does not turn

on.

Water supplies not turned on. Check that the water supplies

to the fitting are turned on.

Closed stop or service valve. Open stop or service valve.

Water does not

come out of the

showerhead when

using the bath

shower mixer.

Diverter mechanism not fully

open.

Pull the diverter up fully.

Insufficient water pressure /

header height.

Refer to the specification

section for minimum

pressures required.

Troubleshooting

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Bristan Sanitärprodukte Handbücher

Bristan

Bristan H64WMT2 Montageanleitung

Bristan

Bristan W BASIN15 C Bedienungsanleitung

Bristan

Bristan JAVA J THBSMVO C Verdrahtungsschema

Bristan

Bristan R2 SHXRR C Montageanleitung

Bristan

Bristan Quest Bedienungsanleitung

Bristan

Bristan W BASIN01 C Verdrahtungsschema

Bristan

Bristan Artisan Bedienungsanleitung

Bristan

Bristan Blade Bath Shower Mixer BL BSM C Bedienungsanleitung

Bristan

Bristan WMNT12 Montageanleitung

Bristan

Bristan Artisan Verdrahtungsschema

Bristan

Bristan PM2 SHCDIV BLK (D2) Verdrahtungsschema

Bristan

Bristan CART 06734B Original Betriebsanleitung

Bristan

Bristan VR1000 Bedienungsanleitung

Bristan

Bristan AR3 SHCDIV C Verdrahtungsschema

Bristan

Bristan RO2 SHXAR C Montageanleitung

Bristan

Bristan Vantage VTX 1/2 C Bedienungsanleitung

Bristan

Bristan TRD RISE C Montageanleitung

Bristan

Bristan W BASIN14 C Verdrahtungsschema

Bristan

Bristan Joy care Montageanleitung

Bristan

Bristan PISA PS2-BSM-C Bedienungsanleitung

Bristan

Bristan CART 06732COMPL Original Betriebsanleitung

Bristan

Bristan CR SHXDIVFF C Verdrahtungsschema

Bristan

Bristan Colonial K BRSNK C Bedienungsanleitung

Bristan

Bristan Artisan AR SNK C Bedienungsanleitung

Beliebte Sanitärprodukte Handbücher anderer Marken

Weka

Weka 506.2020.00E Betriebsanleitung

American Standard

American Standard DetectLink 6072121 Bedienungsanleitung

Kohler

Kohler K-6228 Montageanleitung

Uponor

Uponor Contec TS Bedienungsanleitung

Pfister

Pfister Selia 49-SL Bedienungsanleitung

Fortis

Fortis VITRINA 6068700 Bedienungsanleitung

Kohler

Kohler K-12183 Montageanleitung

Maxxus

Maxxus MX-M206-01 Bedienungsanleitung

Viega

Viega Prevista Pure 8512 Bedienungsanleitung

Kohler

Kohler Centerset K-15240 Montageanleitung

Viega

Viega Prevista Dry 8522.33 Bedienungsanleitung

Sanela

Sanela Lema SLP 59RB Bedienungsanleitung

Elkay

Elkay EDF15AC Installationshandbuch

Hans Grohe

Hans Grohe AXOR Citterio E 36702000 Handbuch

baliv

baliv WT-140 Bedienungsanleitung

Kohler

Kohler Mira Eco Bedienungsanleitung

BELLOSTA

BELLOSTA romina 0308/CC Bedienungsanleitung

Crosswater

Crosswater Heir 18-31 Bedienungsanleitung