Bristan Wine Easyfit Verdrahtungsschema

Please keep these instructions for future reference

Installation Instructions & User Guide

Wine Easyfit Kitchen Sink Mixer

Thank you for choosing Bristan, the UK’s leading taps and showers expert. We have

designed this product with your enjoyment in mind. To ensure that it works to its full

potential, it needs to be fitted correctly. These fitting instructions have been created to give

you all of the information you need and, if you need any further help, please do not hesitate

to give us a call on 0844 701 6273.

Important Safety Information 03

General Specifications 03

Dimensions 04

Installation Requirements 05

Installation 06-08

Maintenance 09

Troubleshooting 10

Guarantee 11

Contents

Important Safety Information

•Please read these instructions thoroughly and retain for future use.

•All products manufactured and supplied by Bristan are safe provided they are installed

correctly, used correctly and receive regular maintenance in accordance with these

instructions.

•If you are in any doubt about your ability to install this product safely you must employ the

services of an experienced qualified plumber.

•Remove all packaging and check the components for damage before starting installation.

•Before starting any installation please consider the following: Prior to drilling into walls,

check that there are no hidden electrical wires, cables or water supply pipes. This can be

checked with the aid of an electronic detector.

•If power tools are used do not forget to:

-Wear eye protection

-Unplug equipment after use

•This product must not be modified in any way as this will invalidate the guarantee.

•These fittings need to be installed in accordance with and meet the requirements of the Water

Supply (Water Fittings) Regulations 1999 and Scottish Byelaws 2004.

General Specifications

Operating pressure range (bar) Min Max

0.3 5.0

Maximum static pressure –10.0 bar

NOTE:-Nominally equal (balanced) inlet supply pressures are recommended for optimum

Performance of mixer taps.

Designed to comply with BS EN 200 for single taps / combination taps for water systems of type 1

and 2 general technical specifications; and to be used within systems designed to BS 6700.

BS 6700 recommends the temperature of stored water should never exceed 65°C. A stored water

temperature of 60°C is considered sufficient to meet all nominal requirements and will minimise

the build up of lime scale in hard water areas.

Dimensions

All measurements are in mm and are approximate

Installation Requirements.

Flexible Connecting Pipes

Care must be taken when connecting the

flexible connection pipes to the household

pipework to ensure they do not bend sharply

and kink or twist.

See below for recommended ways to fit

the flexible connecting pipes

Important: Failure to follow these guidelines may result in poor performance and

damage to the flexible connecting pipes

Isolation Valves

The isolation valves must be

accessible with a suitable flatblade

screwdriver for turning on and for

future servicing purposes

See below for the off and on positions of

the isolation valves.

Installation

Basin Mixer

Installation Cont.

Identify all components are present prior to starting installation using the diagram on

page 06.

1. Spout Assembly x1 9. Grub Screw x2

2. Spout Grub Screw x1 10. Easy Fit Assembly x1

3. Handle x2 11. Flexible Connecting Pipes x2

4. Indice x2 12. Isolation Valve x2

5. Spline Adaptor x2 13. Non-Return Valve x2

6. CD Valve x2 14. Fixing Plate x1

7. Grub Screw x2 15. Hexagonal Key x1

8. Cap x2

Flush through the pipework to ensure removal of debris. Turn off

the mains water supply and close any isolating valves.

1. Fit push-fit connector

Place the ‘push-fit connector’ into the hole in the basin top.

Ensure the rubber washer is fitted to the underside and the side

with ‘FRONT’ on is at the front.

2. Attach hot and cold connectors

A re-enforcing plate, (not supplied or shown in diagram) can be

used to distribute the weight of the tap if fitted to thin worktops or

stainless steel sinks. If required, this should be fitted underneath

work surface above the back nut. Position the back nut under the

basin (with the rubber seal on top), ensuring the locating pin fits

into the hole in the back nut. Insert and loosely tighten the

threaded cold connector by turning the 6mm hexagonal key

clockwise.

Note: The hot connector has 2 flat edges at the top to allow it to fit fully down and close to

the top of the cold connector. Failure to do this may prevent the tap fitting onto the connector.

Important: The push-fit connector must be fully tightened to the back nut before

attaching the flexible connecting pipes.

5. Fit the tap body

Remove the cover cap and place the plinth over the push-fit connector. Grease the push-fit

connector using the sachet of grease provided. Push-fit the tap body onto the connector.

Align the body and tighten the grub screw at the rear of the body, using the long end of the

2.5mm hexagonal key as shown below until finger tight. Remove the hexagonal key and

insert the short end into the grub screw and tighten an extra ¾ to 1 complete turn more to

ensure the tap body is securely tightened to the push-fit connector.

Important: The fitting must be securely attached to the base.

Turn on the mains water supply and open the isolating valves using a suitable flat blade

screwdriver. (See page 05)

Operation

Lowering/Lifting of the lever handles will turn on/off and increase/decrease the flow of water.

The swivel spout also allows for various positioning.

* Tap body may

vary to the one

shown here

Installation Cont.

3. Attach flexible connecting pipes.

Important: Before connecting the flexible connecting

pipes, please refer to the specific installation

requirements on page 5. Carefully screw the ‘flexible

connecting pipes’ into the ‘push-fit connectors’. Fit the

isolation valves (supplied) to the flexible connection pipes

and turn to the 'closed' position as shown on page 5.

Note: A flexible connecting pipe can be fed up through

the hot connector hole and then screwed on if required.

Important: Only tighten the flexible connecting pipe by

hand. Do not overtighten. Connect the isolation valves/flexible

connecting pipes to the household water supply pipes.

4. Cover cap

If required place the cover cap over the push-fit connector

until the tap body is ready to be fitted.

General Cleaning

Your fitting has a high quality finish and should be treated with care to preserve the visible

surfaces. All finishes will wear if not cleaned correctly. The only safe way to clean your

product is to wipe with a soft damp cloth. Stains can be removed using washing up liquid.

All bathroom cleaning products (powders and liquids) will damage the surface of your

fitting, even the non-scratch cleaners.

Note: Never use abrasive detergents or disinfectants or those containing alcohol,

hydrochloric acid or phosphoric acid.

Bristan recommend E-cloth for cleaning all of our bathroom & kitchen

products. Using just water, E-cloth gives a smear free, deep clean by

breaking up and holding dirt, which normal cloths leave behind. Order

through your Bristan stockist. (order code: ECLOTH).

Maintenance

If your fitting begins to leak the following should be carried out;

Isolate both hot and cold water supplies to the tap by either:

•Turning the water supply off at the mains stopcock or

•Turning off the isolation valves to the tap.

1. Remove the cap (8) at the base of the handle (3) to reveal the concealed grub screw (7).

2. Unscrew the grub screw (7) and remove the handle (3) by pulling away from the tap body.

3. Remove the ceramic disc valve (6).

4. Carefully clean the valve (6) and the tap body housing before re-inserting and testing.

5. If necessary replace the valve/s.

Please visit www.bristan.com/sparesfinder in order to find spare parts for this product.

6. Re-fit all of the remaining components and turn on water supply.

7. Check for leaks and contact our helpline if problem persists.

Symptom Cause Remedy

No flow or poor flow

rate.

Partially closed stop or service

valve in water supply pipework to

the tap.

Open stop or service valve.

Head of water is below the

minimum distance required.

Refer to the Specification section

for minimum pressures required.

Possible airlock / blockage in

supply pipework

Remove water supplies from the

fitting and flush the system to

remove any airlocks / debris.

Cartridge / Valve not opening

fully.

Service fitting. Refer to

maintenance section on page 09.

Water dripping for a few

seconds after the tap

has been turned off.

This is caused by ‘capillary

action’ and residual water in the

spout being siphoned out. This

should only last for a couple of

seconds.

Constant dripping /

leaking when the tap is

not in use.

Cartridge / Valve not fully

shutting off.

Service fitting and replace

cartridge / valve. Refer to

maintenance section on page 09.

Fitting does not turn on. Water supplies not turned on. Check that the water supplies to

the fitting are turned on.

Closed stop or service valve. Open stop or service valve.

Troubleshooting

Inhaltsverzeichnis

Andere Bristan Sanitärprodukte Handbücher

Bristan

Bristan HOU SHCDIV C (D7) Verdrahtungsschema

Bristan

Bristan SQR KIT01 BLK D2 Verdrahtungsschema

Bristan

Bristan W BATH05 C Verdrahtungsschema

Bristan

Bristan Joy ThermoSafe Series Montageanleitung

Bristan

Bristan VR1000 Bedienungsanleitung

Bristan

Bristan GLL FLEXSNK C (D1) Verdrahtungsschema

Bristan

Bristan TRD RISE C Montageanleitung

Bristan

Bristan Jute JU BSM C Bedienungsanleitung

Bristan

Bristan WASTES W BASIN04 BB Montageanleitung

Bristan

Bristan WMNT12 Montageanleitung

Bristan

Bristan W BASIN12 C Bedienungsanleitung

Bristan

Bristan Java J BID C Bedienungsanleitung

Bristan

Bristan SOLO SST1000-L Bedienungsanleitung

Bristan

Bristan FHC CTRD02 C Bedienungsanleitung

Bristan

Bristan W BASIN06 C Bedienungsanleitung

Bristan

Bristan VAC BAS C MT (D4) Verdrahtungsschema

Bristan

Bristan 1901 Bedienungsanleitung

Bristan

Bristan DUL3 THBSM C Bedienungsanleitung

Bristan

Bristan R2 SHXRR C Montageanleitung

Bristan

Bristan KN2 SHXAR C Montageanleitung

Bristan

Bristan VAL2 BIB C 6 CD Verdrahtungsschema

Bristan

Bristan DSC SHCDIV C (D7) Verdrahtungsschema

Bristan

Bristan HOU BSM C Verdrahtungsschema

Bristan

Bristan Pisa PS2 BAS C Verdrahtungsschema

Beliebte Sanitärprodukte Handbücher anderer Marken

Weka

Weka 506.2020.00E Betriebsanleitung

American Standard

American Standard DetectLink 6072121 Bedienungsanleitung

Kohler

Kohler K-6228 Montageanleitung

Uponor

Uponor Contec TS Bedienungsanleitung

Pfister

Pfister Selia 49-SL Bedienungsanleitung

Fortis

Fortis VITRINA 6068700 Bedienungsanleitung

Kohler

Kohler K-12183 Montageanleitung

Maxxus

Maxxus MX-M206-01 Bedienungsanleitung

Viega

Viega Prevista Pure 8512 Bedienungsanleitung

Kohler

Kohler Centerset K-15240 Montageanleitung

Viega

Viega Prevista Dry 8522.33 Bedienungsanleitung

Sanela

Sanela Lema SLP 59RB Bedienungsanleitung

Elkay

Elkay EDF15AC Installationshandbuch

Hans Grohe

Hans Grohe AXOR Citterio E 36702000 Handbuch

baliv

baliv WT-140 Bedienungsanleitung

Kohler

Kohler Mira Eco Bedienungsanleitung

BELLOSTA

BELLOSTA romina 0308/CC Bedienungsanleitung

Crosswater

Crosswater Heir 18-31 Bedienungsanleitung