Bristan Zing Safe Touch Bar Mixer Multi Mode Kit Verdrahtungsschema

Please keep these instructions for future reference and request of replacement parts

Zing Safe Touch Bar Mixer Multi Mode Kit

Installation Instructions & User Guide

Thank you for choosing Bristan, the UK’s leading taps and showers expert. We have designed

these products with your enjoyment in mind. To ensure that they work to their full potential, they

need to be fitted correctly. These fitting instructions have been created to give you all of the

Information you need and, if you need any further help, please do not hesitate to give us acall on

0330 026 6273.

Contents Page

1. Important Safety information 03

2. General Information 04

3. Specifications 05

4. Dimensions 06

5. Features 07

6. Installation Requirements 08 – 11

7. Installation 12 –15

8. Commissioning 16

9. In Service Testing 17

10. Annex F 18

11. Maintenance 19

12. Troubleshooting 20 –21

13. Guarantee 22

Important Safety Information

•

•Please read these instructions thoroughly and retain for future use.

•All products manufactured and supplied by Bristan are safe provided they are installed

correctly, used correctly and receive regular maintenance in accordance with these

instructions.

•If you are in any doubt about your ability to install this shower valve safely you must

employ the services of an experienced qualified plumber.

•This shower valve needs to be installed in accordance with, and meet the requirements of

the Water Supply (Water Fittings) Regulations 1999 and ScottishByelaws 2004.

Warning: Do not operate the shower valve if you suspect it is frozen. Do not site the

shower valve where it might be subjected to freezingconditions.

•Do not crush or kink the shower hose (where supplied) as this could damage the hose and

cause leaks.

•Remove all packaging and check the contents for damage before startinginstallation.

Warning: Before starting any installationplease consider the following:before drilling

into walls, check that there are no hidden electrical wires, cables or water supply pipes.

This can be checked with the aid of an electronicdetector.

•If power tools are used do not forget to; -Wear eye protection

-Unplug equipment afteruse

•

•Fitting Isolating valves to the inlet feeds is required for ease of maintenance.

Warning: Before installing the new shower valve it is essential that you thoroughly

flush through the pipework in order to remove any remaining swarf, solder, etc. Failure to

carry out this procedure could cause problems or damage to the workings of the shower

valve.

•It is recommended that when installing the shower valve, full access is provided for

servicing purposes.

•This shower valve must not be modified in any way as this will invalidate theguarantee.

General Information

This product complies with the BS EN 1111:1999 (HP) thermostatic mixing valve standards and

satisfies the requirements of the Water Supply (Water Fittings) Regulations 1999 and current

bylaws.

Designed to be used within systems designed to BS 6700.

BS 6700 recommends the temperature of stored water should never exceed 65ºC. A stored water

temperature of 60ºC is considered sufficient to meet all normal requirements and will minimise

the build up of lime scale in hard water areas (see Map of Hard Water Regions in the UK on page

24).

If the shower valve is installed at low pressure (tank fed), then the minimum distance from the

highest installed position of the showerhead to the underside of the cold tank should be at least

2 metres to ensure adequate performance.

These shower valves should be installed in compliance with the Water Regulations. For further

details contact you Local Water Authority.

Specifications

Inlet Connections: G ½" male thread with 135-165mm centres

Operating Pressure Range: Minimum. 0.2bar, Maximum5.0bar.

Maximum Static Pressure:10.0bar.

Note: Nominally equal (balanced) inlet supply pressures are required for optimum performance. If

pressures are unequal, then apressure reducing valve should be used.

Maximum recommended imbalance between hot and cold supply should not exceed aratio of 5:1

Maximum Outlet Temperature: Factory pre-set to 38ºC with push button override to46ºC (can

be re-set to suit site conditions or personal preference).

Supply Requirements:

Minimum cold water supply temperature: 5ºC

Maximum cold water supply temperature: 25ºC

Maximum hot water supply temperature: 80ºC

(a maximum hot water supply of 55-65ºC is recommended for ablutionarypurposes).

Note: The inlet hot water temperature must be at least 10ºC above the required blend

temperature (e.g. outlet temperature 43ºC: Minimum hot supply53ºC).

Note: Valves operating outside these conditionscannot be guaranteed by the Scheme to operate

as Type 2valves.

All dimensions are in mm’s and are approximate.

Dimensions

Product Features

1. Water Flow Control

Controls the amount or flow of water from

the multi mode handset.

2. Temperature Control

Adjustable temperature control.

The temperature control incorporates

asafety stop facility limiting the water

temperature to 38ºC.

To obtain ahigher water temperature,

press / slide the button on handle (2)

and continue to turn the controlto the

desired temperature.

Safe Touch Feature

This shower valve incorporatesa

safe touch feature. When the shower

valve is in use,the body of the shower

will not get hot and will remain cool.

Shower Handset

The shower handset supplied has 3

spray modes –spray, jet spray and

combination.Simply rotate the spray

head one way or the other until it

‘clicks’ into the desired spray pattern.

Installation Requirements

Cold mainssupply

min

This shower valve must be installed in

compliance with currentwaterregulations.

If you have any doubts about the water

regulation requirements contact yourlocal

water services provider or usethe services

of a professionalplumber.

This shower valve is suitable for use with

the following water supply systems.

•Gravity Fed Hot and Cold

(pressure Balanced)

•Gravity Fed Hot and Mains Cold

(differential pressure –seeSpecification

section on page5.

•Instantaneous Water Heater

(combination boiler)

•Unvented System

•Pumped System

Gravity Fed Hot and Cold

Important: If you install this shower

valve with a gravity fed system, there must

be a minimum head (vertical distance)

from the underside of the cold water

storage tank to the showerhead positionof

at least 2metres.

Note: Pumped system (with Essex flange)

If you install this shower valve to a pumped

gravity fed system where the minimum

head (vertical distance) fromthe underside

of the cold water storagetankto the top of

the hot water cylinder is less than 1 metre

we recommend an Essex flange is used as

shown on page 10.

Flushing Pipework

Important: Before connecting the

shower valve (see Installation on pages 13-

20), supply pipework must be flushed to

clear debris before connecting the shower

valve. Debris will reduce the performance

and life of theshower.

Gravity Fed Hot and MainsCold

2mmin

Cold mainssupply

Installation Requirements

Instantaneous Water Heater Unvented System

Cold mainssupply Cold mains supply

Pumped System Pumped System (with Essex flange)

2m min

If less

than 1m

seenote.

Cold mainssupply Cold mains supply

Key: PumpIsolating

Valve

Reducin

g Valve

Shower

Valve

Essex

Flang

2m min

50mm

Installation Requirements

These fittings need to be installed in

accordance with the following Installation

Requirements and Notes (IRN) to ensure

they meet the requirements of the Water

Supply (Water Fittings) Regulations 1999

and the Scottish Byelaws 2004.

IRN R001: See text of entry forInstallation

Requirements or Notes.

IRN R040 -Schedule 2-15 (1): The fitting shall

be installed so that its outlet discharges above

the spill-over level ofany fixedappliance as

indicatedbelow:-

For backflow protection in domestic or

installations up to, and including, Fluid

Category 3.

If the fitting cannot be installed as indicated in

the table opposite it shall be installed aseither

aor bbelow:

a: with an approved double check valve

assembly or some other no less

effective backflow prevention device

immediately upstream of theinlet.

b: so that it draws water by gravity only froma

cistern, or cylinder havinga

permanently open vent pipe, and the

distributing pipe supplies no otherfitting

(other than draining tap) at a lowerlevel.

For backflow protection in premises or

installations up to, and including Fluid

Category 5.

The vertical distance of the outlet above the

spill-over level shall be not less than 20mm or

twice the diameter of the inlet pipe to the

fitting, which ever is the greater. If the fitting

cannot be installed as indicated it shall be

installed with a backflow prevention

arrangement suitable for the FluidCategory.

Size of tap or

combination fitting.

Vertical distance

of outlet above

spill-over level.

1. Not exceeding 1/2

in 20mm

2. Exceeding 1/2 in

but not exceeding

3/4 in

25mm

3. Exceeding 3/4 in 70mm

Inhaltsverzeichnis

Andere Bristan Sanitärprodukte Handbücher

Bristan

Bristan GLL FLEXSNK C (D1) Verdrahtungsschema

Bristan

Bristan DUL2 SHXARFF C Verdrahtungsschema

Bristan

Bristan CRZ SHXDIVCTFF C Verdrahtungsschema

Bristan

Bristan CRZ2 SHXDIVCTFF C Verdrahtungsschema

Bristan

Bristan Quadrato Tap Range Verdrahtungsschema

Bristan

Bristan SMILE SM 1/2 C D6 Verdrahtungsschema

Bristan

Bristan TG SNK C Verdrahtungsschema

Bristan

Bristan Java J BF C Bedienungsanleitung

Bristan

Bristan CFC33 Bedienungsanleitung

Bristan

Bristan Hourglass HOU BSM C Verdrahtungsschema

Bristan

Bristan SQR KIT01 BLK D2 Verdrahtungsschema

Bristan

Bristan Descent Series Bedienungsanleitung

Bristan

Bristan MIO BAS C (D1) Verdrahtungsschema

Bristan

Bristan VR1000 Bedienungsanleitung

Bristan

Bristan W-BASIN01-C Verdrahtungsschema

Bristan

Bristan W BASIN07 C Verdrahtungsschema

Bristan

Bristan EF KIT PK Verdrahtungsschema

Bristan

Bristan Quest Easyfit Verdrahtungsschema

Bristan

Bristan Cinnamon Verdrahtungsschema

Bristan

Bristan SOLO SST1000-L Bedienungsanleitung

Bristan

Bristan NIVA NVA BSM C Verdrahtungsschema

Bristan

Bristan FHC CTRD01 C Bedienungsanleitung

Bristan

Bristan IRN R001 Bedienungsanleitung

Bristan

Bristan VAC BAS C MT (D4) Verdrahtungsschema

Beliebte Sanitärprodukte Handbücher anderer Marken

Weka

Weka 506.2020.00E Betriebsanleitung

American Standard

American Standard DetectLink 6072121 Bedienungsanleitung

Kohler

Kohler K-6228 Montageanleitung

Uponor

Uponor Contec TS Bedienungsanleitung

Pfister

Pfister Selia 49-SL Bedienungsanleitung

Fortis

Fortis VITRINA 6068700 Bedienungsanleitung

Kohler

Kohler K-12183 Montageanleitung

Maxxus

Maxxus MX-M206-01 Bedienungsanleitung

Viega

Viega Prevista Pure 8512 Bedienungsanleitung

Kohler

Kohler Centerset K-15240 Montageanleitung

Viega

Viega Prevista Dry 8522.33 Bedienungsanleitung

Sanela

Sanela Lema SLP 59RB Bedienungsanleitung

Elkay

Elkay EDF15AC Installationshandbuch

Hans Grohe

Hans Grohe AXOR Citterio E 36702000 Handbuch

baliv

baliv WT-140 Bedienungsanleitung

Kohler

Kohler Mira Eco Bedienungsanleitung

BELLOSTA

BELLOSTA romina 0308/CC Bedienungsanleitung

Crosswater

Crosswater Heir 18-31 Bedienungsanleitung