Bristan Descent Series Bedienungsanleitung

Please keep this booklet for future

reference.

Installer, when you have read these

instructions please ensure you leave them

with the user.

Installation Instructions

Descent Tap Range

Models covered:

DSC BAS C, DSC BF C, DSC BSM C,

DSC 1HBF C, DSC FSBSM C

Contents

Thank you for choosing Bristan, the UK’s leading taps and showers expert.

We have designed this product with your enjoyment in mind. To ensure that it works

to its full potential, it needs to be ﬁtted correctly. These ﬁtting instructions have been

created to give you all of the information you need and, if you need any further help,

please do not hesitate to contact us.

Important Safety Information................................................... 3

General Information ................................................................. 4

Speciﬁcations ........................................................................... 4

Dimensions............................................................................... 5-7

Installation Requirements ....................................................... 8

Installation................................................................................ 9-11

Basin Mixer & 1 Hole Bath Filler............................................. 9

Bath Filler & Bath Shower Mixer............................................. 10

Floor Standing Bath Shower Mixer.......................................... 11

Maintenance ............................................................................. 12

Troubleshooting........................................................................ 13

Guarantee ................................................................................. 14-15

Need help? Give us a call on 0844 701 6273 and speak to one of our trained advisers.

Important Safety Information

•Please read these instructions thoroughly and retain for future use.

•All products manufactured and supplied by Bristan are safe provided they are

installed, used correctly and receive regular maintenance in accordance with these

instructions.

•If you are in any doubt about your ability to install this product safely you must

employ the services of an experienced qualiﬁed plumber.

•This product needs to be installed in accordance with, and meet the requirements of

the Water Supply (Water Fittings) Regulations 1999 and Scottish Byelaws 2004.

•Remove all packaging and check the ﬁtting for damage before starting installation.

•Warning: Before starting any installation please consider the following: before

drilling into walls, check that there are no hidden electrical wires, cables or water

supply pipes. This can be checked with the aid of an electronic detector.

•If power tools are used do not forget to: - Wear eye protection

- Unplug equipment after use

•Important: Remember to turn off the mains water supply before connecting to any

existing pipe work. Fitting isolating valves to the inlet feeds is recommended for ease

of maintenance.

•Warning: Before installing this product it is essential that you thoroughly ﬂush

through the pipework in order to remove any remaining swarf, solder, etc.

Failure to carry out this procedure could cause problems or damage to the workings of

the tap.

•Take care when handling the ‘ﬂexible connecting pipes’, do not bend, twist or crush

them. Only tighten the pipes by hand.

•Do not crush or kink the shower hose, this could damage the hose and cause leaks.

• This product must not be modiﬁed in any way as this will invalidate the guarantee.

Need help? Give us a call on 0844 701 6273 and speak to one of our trained advisers.

General Information

This product has been tested to the Water Regulations Advisory Scheme (WRAS) and

satisﬁes the requirements of the Water Supply (Water Fittings) Regulations 1999 and

current bylaws. For full Installation Requirements & Notes (IRN) please visit

www.wras.co.uk/directory.

Designed to comply with BS EN 200 for combination taps to be used within systems

designed to BS 6700.

BS 6700 recommends the temperature of stored water should never exceed 65°C.

A stored water temperature of 60°C is considered sufﬁcient to meet all normal

requirements and will minimise the build up of lime scale in hard water areas.

If installing this product on a low pressure (tank fed) system please see speciﬁcation

table below to determine the minimum distance required from undeside of the cold

water tank to the outlet.

These taps and mixers should be installed in compliance with the Water Regulations.

Where the supplies are unbalanced, i.e. Hot water from cylinder tank / cold from the

mains, approved check valves must be ﬁtted in the supply pipes.

For further details contact your Local Water Authority.

Speciﬁcations

Product Code

Working pressure

Inlet

Minimum distance

from cold water tank

to outlet (metres)

Min Max

DSC BAS C 0.2 5.0 M10 15mm Compression Flexible Tails 2

DSC BF C 0.2 5.0 3/4" BSP Threaded Tail 2

DSC BSM C 0.3 5.0 3/4" BSP Threaded Tail 3

DSC 1HBF C 1.0 5.0 M12 15mm Compression Flexible Tails 10

DSC FSBSM C 1.5 5.0 M12 15mm Compression Flexible Tails 15

Maximum static pressure- 10.0 bar

System Requirements:

Gravity fed hot & cold (Equal pressures)

Gravity fed hot & cold (Differential pressure, maximum ratio 5:1)

Unvented systems

Instantaneous water heater (Combination boiler)

Need help? Give us a call on 0844 701 6273 and speak to one of our trained advisers.

Dimensions

Dimensions are approximate and in millimetres.

Need help? Give us a call on 0844 701 6273 and speak to one of our trained advisers.

Basin Mixer

Bath Filler

Basin Mixer

137

180

140

147

107

Dimensions Cont.

1 Hole Bath Filler

Dimensions are approximate and in millimetres.

Need help? Give us a call on 0844 701 6273 and speak to one of our trained advisers.

Bath Shower MixerBath Shower Mixer

137

180

176

209

128

108

Dimensions Cont.

Need help? Give us a call on 0844 701 6273 and speak to one of our trained advisers.

Dimensions are approximate and in millimetres.

843

375

190

220

Floor Standing Bath Shower Mixer

Installation Requirements

Flexible Connecting Pipes

Care must be taken when connecting the ﬂexible connection pipes to the household pipework to

ensure they do not bend sharply and kink or twist.

See below for recommended ways to ﬁt the ﬂexible connecting pipes.

Slight

bend

90°

Angle

Kink Curved

round

Twists

Important: Failure to follow these guidelines may result in poor performance and damage

to the ﬂexible connecting pipes.

Important: Full access must be made available on installation for future maintenance/

servicing purposes.

Need help? Give us a call on 0844 701 6273 and speak to one of our trained advisers.

Installation

Need help? Give us a call on 0844 701 6273 and speak to one of our trained advisers.

Basin Mixer / 1 Hole Bath Filler

1. Screw the ﬂexi tails into the bottom of

the body by hand only (DO NOT

OVERTIGHTEN).

2. Feed the ﬂexi tails through the hole

in the basin / bath, ensuring the washer

is ﬁtted between the tap body and ﬁxing

surface to ensure a water tight seal.

3. Screw the ﬁxing rods into the bottom

of the tap body. Slide the 'C' shaped

rubber washer and 'C' shaped metal

washer onto the ﬁxing rods up to the

underside of the basin / bath.

4. To secure the tap body in place tighten

the ﬁxing nuts onto the ﬁxing rods until

the are fully tightened against the

'C' shaped metal washer. The ﬁxing nuts

can be tightened with a suitable spanner.

5. Connect the ﬂexi tails to the hot and

cold water supplies.

6. Turn on both water supplies,

operate the handle in both directions,

letting the water ﬂow for a few minutes to

ﬂush through the system.

7. Fit the clicker waste (for basin mixer

only) ensuring the rubber washer is ﬁtted

between the basin and the waste. Place

the other rubber washer under the basin

and secure by tightening the backnut, in

order to ﬁll the basin, the button in the

middle of the waste needs to be pressed

down. To release the water, press the but-

ton again.

8. Check all joints and connections for any

leaks.

Installation Cont.

Bath Filler and Bath Shower Mixer

1. Fit the tap body to the bath ensuring

that the washers are ﬁtted between the

body and the bath to create a water tight

seal.

2. Secure the body to the bath using the

washers and metal backnut. Tighten

the backnuts onto the threaded tails. A

suitable spanner may be required to fully

tighten the backnuts.

3. Connect the hot and cold water

supplies to the threaded tails using

a ¾” BSP connector (not supplied).

4. Bath Shower Mixer only - ﬁt the shower

hose to the hose outlet using the small

sealing washer, and the handset to the

hose using the small washer.

Important: Prior to the drilling into

walls, check there no hidden electrical

wires, cables or water supply pipes with

the aid of an electronic detector.

If you use power tools do not forget to:

• Wear eye protection

• Unplug equipment after use

Fit the wall bracket (not shown) to the wall

using the ﬁxings supplied, ensuring the

handset and hose reaches it.

5. Turn on both water supplies and turn

both handles to the on position, letting the

water ﬂow for a few minutes.

6. Check all joins and connections for any

leaks.

7. To switch from bath to shower mode,

pull the diverter knob up and turn, to

revert back to bath ﬁlling mode push the

diverter knob back down.

Need help? Give us a call on 0844 701 6273 and speak to one of our trained advisers.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Bristan Sanitärprodukte Handbücher

Bristan

Bristan EXD BAS C Bedienungsanleitung

Bristan

Bristan Blade Bath Shower Mixer BL BSM C Bedienungsanleitung

Bristan

Bristan W BATH05 C Verdrahtungsschema

Bristan

Bristan SAI 1/2 C Montageanleitung

Bristan

Bristan N2 SHCDIV C (D7) Verdrahtungsschema

Bristan

Bristan Buzz Verdrahtungsschema

Bristan

Bristan Java J BF C Bedienungsanleitung

Bristan

Bristan HOU 1HBF C Verdrahtungsschema

Bristan

Bristan CR SHXDIVFF C Verdrahtungsschema

Bristan

Bristan FIXED HEADS FHC ABRD01 C Bedienungsanleitung

Bristan

Bristan W-BASIN01-C Verdrahtungsschema

Bristan

Bristan QD SHXSMFF C D3 Verdrahtungsschema

Bristan

Bristan ZI SHXSMCT Verdrahtungsschema

Bristan

Bristan Quest QST BF C Bedienungsanleitung

Bristan

Bristan W BASIN08 C Bedienungsanleitung

Bristan

Bristan W BASIN12 C Bedienungsanleitung

Bristan

Bristan Manhattan MH SNK C Bedienungsanleitung

Bristan

Bristan Hourglass HOU BSM C Verdrahtungsschema

Bristan

Bristan SAF SHCDIV BLK (D1) Verdrahtungsschema

Bristan

Bristan Artisan Bedienungsanleitung

Bristan

Bristan Blade BL BAS C Bedienungsanleitung

Bristan

Bristan Artisan AR2 SHXMTFF2 C Montageanleitung

Bristan

Bristan CRAZE CRZ2 SHXDIVCTFF C Verdrahtungsschema

Bristan

Bristan VAX DSM C Verdrahtungsschema

Beliebte Sanitärprodukte Handbücher anderer Marken

Weka

Weka 506.2020.00E Betriebsanleitung

American Standard

American Standard DetectLink 6072121 Bedienungsanleitung

Kohler

Kohler K-6228 Montageanleitung

Uponor

Uponor Contec TS Bedienungsanleitung

Pfister

Pfister Selia 49-SL Bedienungsanleitung

Fortis

Fortis VITRINA 6068700 Bedienungsanleitung

Kohler

Kohler K-12183 Montageanleitung

Maxxus

Maxxus MX-M206-01 Bedienungsanleitung

Viega

Viega Prevista Pure 8512 Bedienungsanleitung

Kohler

Kohler Centerset K-15240 Montageanleitung

Viega

Viega Prevista Dry 8522.33 Bedienungsanleitung

Sanela

Sanela Lema SLP 59RB Bedienungsanleitung

Elkay

Elkay EDF15AC Installationshandbuch

Hans Grohe

Hans Grohe AXOR Citterio E 36702000 Handbuch

baliv

baliv WT-140 Bedienungsanleitung

Kohler

Kohler Mira Eco Bedienungsanleitung

BELLOSTA

BELLOSTA romina 0308/CC Bedienungsanleitung

Crosswater

Crosswater Heir 18-31 Bedienungsanleitung