Bunn HC-2 Bedienungsanleitung

ILLUSTRATED PARTS CATALOG

Designs, materials, weights, specifications, and dimensions for equipment or replacement parts

are subject to change without notice.

BUNN-O-MATICCORPORATION

POST OFFICE BOX 3227

SPRINGFIELD, ILLINOIS 62708-3227

PHONE: (217) 529-6601 FAX: (217) 529-6644

www.bunnomatic.com

CAUTION

HOT

LIQUID

PUSHandHOLDBUTTONUNTIL CUPIS 2/3 FULL, THENRELEASE

CAUTION: HOT LIQUIDS

HC-2

HC-3

(prior to S/N HC00025000)

BUNN

WARRANTY

Bunn-O-Matic Corp. (“Bunn”) warrants the equipment manufactured by it to be commercially free from defects

in material and workmanship existing at the time of manufacture and appearing within one year from the date of

installation. In addition:

1.) Bunn warrants electronic circuit and/or control boards to be commercially free from defects in material and

workmanship for three years from the date of installation.

2.) Bunn warrants the compressor on refrigeration equipment to be commercially free from defects in material

and workmanship for two years from the date of installation.

3.) Bunn warrants that the grinding burrs on coffee grinding equipment will grind coffee to meet original factory

screen sieve analysis for three years from date of installation or for 30,000 pounds of coffee, whichever comes first.

This warranty does not apply to any equipment, component or part that was not manufactured by Bunn or that,

in Bunn’s judgement, has been affected by misuse, neglect, alteration, improper installation or operation, improper

maintenance or repair, damage or casualty.

THE FOREGOING WARRANTY IS EXCLUSIVE AND IS IN LIEU OF ANY OTHER WARRANTY, WRITTEN OR

ORAL, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF EITHER

MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. The agents, dealers or employees of Bunn are

not authorized to make modifications to this warranty or to make additional warranties that are binding on Bunn.

Accordingly, statements by such individuals, whether oral or written, do not constitute warranties and should not

be relied upon.

The Buyer shall give Bunn prompt notice of any claim to be made under this warranty by telephone at (217)

529-6601 or by writing to Post Office Box 3227, Springfield, Illinois, 62708-3227. If requested by Bunn, the Buyer

shall ship the defective equipment prepaid to an authorized Bunn service location. If Bunn determines, in its sole

discretion, that the equipment does not conform to the warranty, Bunn shall repair the equipment with no charge

for parts during the warranty period and no charge for labor by a Bunn Authorized Service Representative during

the warranty period. If Bunn determines that repair is not feasible, Bunn shall, at its sole option, replace the

equipment or refund the purchase price for the equipment.

THE BUYER’S REMEDY AGAINST BUNN FOR THE BREACH OF ANY OBLIGATION ARISING OUT OF THE SALE

OF THIS EQUIPMENT, WHETHER DERIVED FROM WARRANTY OR OTHERWISE, SHALL BE LIMITED, AS

SPECIFIED HEREIN, TO REPAIR OR, AT BUNN’S SOLE OPTION, REPLACEMENT OR REFUND.

In no event shall Bunn be liable for any other damage or loss, including, but not limited to, lost profits, lost sales,

loss of use of equipment, claims of Buyer’s customers, cost of capital, cost of down time, cost of substitute

equipment, facilities or services, or any other special, incidental or consequential damages.

26531 021502

TABLE OF CONTENTS

Auger Drive and Hopper Assembly ................................................................................................................................................ 8

Covers, Panels and Drip Tray ......................................................................................................................................................... 4

Dispense Valves and Lines .......................................................................................................................................................... 18

Door, Lamps and Panels ................................................................................................................................................................ 6

Electrical Controls........................................................................................................................................................................ 20

Mixing/Whipper Chambers and Drive Motor ............................................................................................................................... 10

Numerical Index .......................................................................................................................................................................... 22

Strainer, Solenoid, Fill Valve and Lines ........................................................................................................................................ 14

Tank, Heater and Overflow Protection .......................................................................................................................................... 12

326531 060600

BUNN

®HC-3

HC-2

CAUTION

HOT

LIQUID

COVERS, PANELS AND DRIP TRAY

P899

20 21 22

26531 060600

ITEM PART NO. QTY. DESCRIPTION

126504.0000 2 Hinge

02308.0000 8 Screw, Pan Head 8 - 32 x .375”

2 25796.0000 1 Cover, Top Rear (SST)

25796.0001 1 Cover, Top Rear (Black)

02331.0000 4 Screw, Truss Head 10 - 32 x .375” (SST)

02331.0001 4 Screw, Truss Head 10 - 32 x .375” (Black)

325901.0000 1 Cover, Top Front (SST)

25901.0001 1 Cover, Top Front (Black)

4-- - - - - - - 1 Panel W/Decals, Front (Not available)(Early Models without Hopper Delay)

- - - - - - - - 1 Panel W/Decals, Front (Not available)(Late Models with Hopper Delay)

02331.0000 2 Screw, Truss Head 10 - 32 x .375”

526532.0000 1 Schematic, 120 & 120/240V (Early Models without Hopper Delay)

26702.0000 1 Schematic, 120 & 120/240V (Late Models with Hopper Delay)

626524.0000 1 Decal, Tank Heater Switch

7 26523.0000 1 Decal, Rinse/Run Switch

826522.0000 1 Decal, Hot/Cold Switch

926232.0000 1 Cover, Right Side (SST)

26232.0001 1 Cover, Right Side (Black)

01311.0000 6 Screw, Truss Head 8 - 32 x .25”

10 25414.0000 1 Cover, Access (SST)

25414.0001 1 Cover, Access (Black)

01311.0000 2 Screw, Truss Head 8 - 32 x .25” (SST)

01311.0003 2 Screw, Truss Head 8 - 32 x .25” (Black)

11 26233.0000 1 Panel, Splash

01311.0000 4 Screw, Truss Head 8 - 32 x .25”

12 26749.0000 1 Plate W/Decals, Cup Stop (Includes item 13 & 2 of item 22 - also order item 14)

01311.0001 2 Screw, Truss Head 8 - 32 x .25” Locking

13 12368.0001 1 Decal, Caution-Hot Liquid

14 26576.0000 1 Decal, Cup Placement (HC-3 Models) (Shown)

26576.0002 1 Decal, Cup Placement (HC-2 Models)

15 26509.0000 1 Cover, Drip Tray

16 26886.1000 1 Drip Tray Assy (Includes 4 of item 22)

17 26751.0000 1 Cover W/Decals, Rear & Bottom (Includes items 18 & 19)

18 00831.0000 1 Decal, Warning-Electrical

19 00656.0000 1 Decal, Comply to Plumbing Code

20 25887.0000 1 Cover, Left Side (SST)

25887.0001 1 Cover, Left Side (Black)

01311.0000 6 Screw, Truss Head 8 - 32 x .25”

21 26528.0000 4 Leg, 4.0” Adjustable (Also see item 25)

22 03996.0000 10 Pad, Rubber 1.25” Dia.

23 20621.0000 6 Plug, Hole .203” Dia.

24 27290.0000 1 Kit, Hopper Stabilizer

25 13255.0003 1 Kit, Leg 4.0” Adjustable (Includes 4 each of items 21 & 22) (Not illustrated)

COVERS, PANELS AND DRIP TRAY

Also order item 24

26531 021502

BUNN

®HC-3

HC-2

BUNN

REMOVINGANDCLEANING THE WHIPPERCHAMBERS

(Once a week)

THOROUGHCLEANING OFTHE HOPPERS

(Once a week)

FLUORESCENT LAMPREPLACEMENT

(When lights flicker and are hard to start)

RECOMMENDEDDAILY CLEANING ANDMAINTENANCE TIPS.

1. Empty Drip Tray and wash in a solution of dish detergent.

2. Rinse out the Whipper Chambers by placing the RINSE/RUNswitch in the "RINSE"

position and activating the DISPENSE switches for 3 to 5 second bursts.

3. Remove Hoppers and refill with product.

WHIPPER CHAMBER

STEAM COLLECTOR

MIXING CHAMBER

O-RING

FROTHER

EJECTOR ELBOW

AUGER

AUGER DRIVE SHAFT

AUGER DRIVE BRACKET

RETAINING

CLIP

AGITATOR DISK

AGITATOR SUPPORT ROD

LAMP

LAMPHOLDER

Open the Cabinet Door.

Remove the Upper Inner Door Panel.

Rotate Lamp90°and remove from the Lamp Holders.

Insert new Lamp into LampHolders and turn 90°until

the pins snap in place.

Open the Cabinet Door and raise the Top Cabinet Lid.

Remove the Hopper fromthe cabinet; empty the contents.

Pull off theEjector Elbow andremove the Hopper Cover.

Remove the Agitator Disk by pulling agitator support Rod

towards Agitator Disk.

Remove Auger by pulling it out front of Hopper.

Remove the Auger Drive Shaft by removing Retaining

Open the Cabinet Door.

Remove the Steam collector by pulling it forward and at

the sametime twisting it clockwise.

Pull the Mixing Chamber out of the Whipping Chamber.

Twist the WhippingChamber clockwise and pull it off the

WhippingChamber Receptacle.

Pull the Frother off the Motor Shaft. Notice the flat key-

UPPER INNER

DOOR PANEL

P900

DOOR, LAMPS AND PANELS

9 10 11 12 14 13

26531 060600

ITEM PART NO. QTY. DESCRIPTION

126752.0000 1 Door W/Decal (SST)(Includes Item 3 - also order item 2)

26752.0001 1 Door W/Decal (Black)(Includes Item 3 - also order item 2)

27307.0000 1 Door W/Decal (SST)(Includes Item 3 - also order item 2)

27307.0001 1 Door W/Decal (Black)(Includes Item 3 - also order item 2)

27307.0002 1 Door W/Decal (Black Coated)(Includes Item 3 - also order item 2)

226525.0000 1 Decal, Door Front (HC-3 Models) (Shown)

26525.0002 1 Decal, Door Front (HC-2 Models)

311646.0000 1 Decal, Caution Hot Liquids

425898.0000 1 Latch (Early Models)

25899.0000 1 Latch, Magnetic Snap-in (Late Models)

526444.0000 2 Bushing, Strain Relief

626353.0000 2 Bracket, Lamp

02308.0000 4 Screw, Pan Head #8 - 32 x .375"

726239.0000 2 Lamp, Fluorescent - 8 Watts

826539.0000 4 Lamp Holder, Fluorescent

02361.0000 8 Screw, Pan Head #4 - 40 x .25"

926520.0000 1 Display, Graphics (Cafe Scene)

26520.0001 1 Display, Graphics (Fireside Scene)

10 26348.0000 2 Window

11 26354.0000 2 Clamp, Window

02308.0000 4 Screw, Pan Head #8 - 32 x .375"

12 26753.0000 1 Cover W/Decal, Door - Upper (Includes item 13)

01311.0000 8 Screw, Truss Head #8 - 32 x .25"

13 26521.0000 1 Decal, Cleaning

14 27520.1000 1 Cover, Door - Bottom

01311.0000 6 Screw, Truss Head #8 - 32 x .25"

15 25897.0000 2 Hinge, Door (Early Models)

27296.0000 2 Hinge, Door (Late Models)

02331.0000 8 Screw, Truss Head #10 - 32 x .375" (Early Models)

02330.0001 8 Screw, Truss Head #10 - 32 x .375" (Late Models)

16 05920.0000 2 Clamp, Cable

17 00619.0010 4 Plug, Hole .438" Dia.

18 26892.0000 1 Plate, Strain Relief

19 26507.0000 1 Wiring Harness, Door Interconnect (Includes item 18 & 1 of item 5)

20 26506.0000 1 Wiring Harness, Door

21 26537.0000 1 Decal, Flavors

22 27295.0000 1 Handle, Snap-in (Late Models)

DOOR, LAMPS AND PANELS

Not illust.

Early Models

Late Models

26531 060600

BUNN

®HC-3

HC-2

FIRST TYPE

AUGER DRIVE SHAFT

AUGER DRIVE AND HOPPER ASSEMBLY

P901

LOW DISPENSE AUGER

FIRST TYPE

HOPPER SUPPORT PANEL

26531 060600

ITEM PART NO. QTY. DESCRIPTION

* HC-2 Models

** HC-3 Models

***

-26126.1001 2 3 Hopper Assy (22 Tooth Agitator Disk)

-26126.1000 2 3 Hopper Assy (30 Tooth Agitator Disk)

-26126.1002 2 3 Hopper Assy (22 Tooth Agitator Disk) (Low Dispense)

126125.0000 1 1 Lid, Hopper

221358.0000 4 4 Clip, Retainer

321357.0000 4 4 Shaft, Wiper

426436.0000 1 1 Rod, Agitator Support

526449.0000 1 1 Spring

626441.0000 4 4 Wire, Agitator

726435.0000 1 1 Disk, Agitator (22 Teeth)

26435.0001 1 1 Disk, Agitator (30 Teeth)

825742.0000 1 1 Bushing, Auger Drive Shaft

921745.0000 1 1 Clip, Retainer (First Type)

21358.0000 1 1 Clip, Retainer (Second Type)

10 - - - - - - - - 1 1 Shaft, Auger Drive (First Type) (Not available order Second Type

Auger Drive Shaft and Second Type item 9)

26940.0000 1 1 Shaft, Auger Drive (Second Type)

11 26434.0000 1 1 Hopper

12 26112.0001 1 1 Auger, Wire (Use with 22 Tooth Disk)

21355.0001 1 1 Auger, Wire (Use with 30 Tooth Disk)

26864.0000 1 1 Auger, Wire (Use with 22 Tooth Disk) (Low Dispense)

13 25903.0000 1 1 Elbow, Ejector

14 25744.0000 1 1 Bracket, Auger Drive

15 21365.0000 1 1 Washer .31" I.D. x .56" O.D.

16 25743.0000 1 1 Locknut

17 20960.0000 2 3 Screw, Shoulder #6 - 32 x .375"

01520.0000 2 3 Lockwasher, Split #6

00906.0000 2 3 Nut, Hex #6 - 32

00991.0002 2 3 Nut, Locking #6-32 (Late Models)

18 - - - - - - - - 1 1 Panel, Hopper Support (First Type) (Not available order Second Type)

27068.0000 1 1 Panel, Hopper Support (Second Type)

01311.0000 4 4 Screw, Truss Head #8 - 32 x .25"

19 25794.0000 2 3 Bracket, Motor Mounting

01311.0001 8 12 Screw, Truss Head #8 - 32 x .25" Locking

20 00620.0000 1 1 Clamp, Cable

21 26754.0000 2 3 Gearmotor W/Pin, Auger (Includes item 23)

01311.0000 8 11 Screw, Truss Head #8 - 32 x .25"

01315.0000 1 1 Screw, Truss Head #8 - 32 x .375"

22 26401.0000 2 3 Dust Seal, Hopper Motor

23 26247.0000 2 3 Pin, Spring .094" Dia. x 1.0"

24 26496.0000 1 - Plate, Hopper Motor

00970.0000 2 - Nut, Keps #8 - 32

AUGER DRIVE AND HOPPER ASSEMBLY

(Includes items

1 thru 16)

Early Models

26531 021502

BUNN

®HC-3

HC-2

P902

MIXING/WHIPPER CHAMBERS AND DRIVE MOTOR

13 12 11 10 9 8

26531 031602

Andere Handbücher für HC-2

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Bunn Getränkespender Handbücher

Bunn

Bunn IMIX-5 Bedienungsanleitung

Bunn

Bunn TCD-1 Bedienungsanleitung

Bunn

Bunn LCR-2C Bedienungsanleitung

Bunn

Bunn ThermoFresh 44050.0250 Kurzanleitung

Bunn

Bunn IMIX Betriebsanleitung

Bunn

Bunn FMD-1 Gebrauchsanweisung

Bunn

Bunn ICD3 Betriebsanleitung

Bunn

Bunn JDF-2S Bedienungsanleitung

Bunn

Bunn LCR-3 HV Bedienungsanleitung

Bunn

Bunn ULTRA 2 Slush Puppie Bedienungsanleitung

Bunn

Bunn iMIX-3S Bedienungsanleitung

Bunn

Bunn BUNN-O-MATIC ULTRA-1 Bedienungsanleitung

Bunn

Bunn CDS-2 Gebrauchsanweisung

Bunn

Bunn TCD Betriebsanleitung

Bunn

Bunn SRU/U3 Fehlerbehebungshandbuch

Bunn

Bunn LCR-3 HV Fehlerbehebungshandbuch

Bunn

Bunn Liquid Autofill Kits Bedienungsanleitung

Bunn

Bunn FMD-1 Bedienungsanleitung

Bunn

Bunn FMD-4 Gebrauchsanweisung

Bunn

Bunn AFPO-2 Fehlerbehebungshandbuch

Bunn

Bunn IMIX-3S+ Bedienungsanleitung

Bunn

Bunn TDO-N-4.0 Betriebsanleitung

Bunn

Bunn FMD DBC-3 Installationsanleitung

Bunn

Bunn JDF-2S Bedienungsanleitung

Beliebte Getränkespender Handbücher anderer Marken

PEGAS

PEGAS Evolution Bedienungsanleitung

Ugolini

Ugolini MT micro Bedienungsanleitung

Gekkeikan

Gekkeikan Sake Machine Bedienungsanleitung

Olympia

Olympia DH709 Bedienungsanleitung

Marco

Marco ECOSMART PB10 Bedienungsanleitung

Marvel

Marvel ML24BN Series Handbuch

Cecilware

Cecilware 2K-GB-LD Handbuch

Sure Vend

Sure Vend 673 Bedienungsanleitung

Cornelius

Cornelius 2 Flavor Post-Mix Cold Coffee Dispenser Quest... Bedienungsanleitung

Nostalgia Electrics

Nostalgia Electrics KEG7000SS Bedienungsanleitung

Servend

Servend SV-200 Bedienungsanleitung

EdgeStar

EdgeStar VBR440 Bedienungsanleitung

Cornelius

Cornelius A.B.S. Unit Bedienungsanleitung

CDS AUTOMATEN

CDS AUTOMATEN ML-16C2-C Bedienungsanleitung

Siemens

Siemens GA 3000 Gebrauchsanweisung

Cornelius

Cornelius FCB V4 Technische Daten

Selbach

Selbach Fruit Juice dispenser Bedienungsanleitung

Taylor

Taylor C302NP Bedienungsanleitung