Burkert 6026 Bedienungsanleitung
Bedienungsanleitung
Manuel d‘utilisation
Operating Instructions
Type 6026
2/2-way valve
2/2-Wege-Ventil
Vanne 2/2 voies
2
2 INTENDED USE
Unauthorised use of the Type6026 solenoid valve may be dan-
gerous to people, nearby equipment and the environment.
The device is designed for blocking, dosing, lling and ventilating
gaseous and liquid media.
▶When using the device, observe the authorised data, operating
conditions and deployment conditions specied in the contract
documents and in the operating instructions.
▶Prerequisites for safe and trouble-free operation are correct
transportation, correct storage and installation as well as careful
operation and maintenance.
▶Only use the device as intended.
▶Check the media resistance.
2.1 Denition of terms
The term “device” used in these instructions always refers to the
Type 6026 solenoid valve.
1 OPERATING INSTRUCTIONS
The operating instructions contain important information.
▶Carefully read these instructions and follow the safety instructions.
▶Store the instructions in such a way that they are available to all
users.
▶The liability and warranty for the Type 6026 device will be invali-
dated if the operating instructions are not followed.
1.1 Symbols
▶highlights instructions to avoid a danger.
→highlights a procedure which you must carry out.
Warning of injuries:
DANGER!
Imminent danger! Serious or fatal injuries.
WARNING!
Potential danger! Serious or fatal injuries.
CAUTION!
Danger! Moderate or minor injuries.
Warning of damage:
NOTE!
english
3
2.2 Isolation
The device must not be isolated more than
2cm from the body edge upwards to the
actuator.
max. 2 cm
3 BASIC SAFETY INSTRUCTIONS
These safety instructions do not make allowance for any contin-
gencies and events which may arise during installation, operation
and maintenance.
Risk of injury from high pressure.
▶Before loosening lines or valves, switch o the pressure and
drain the lines.
Risk of injury due to electric shock.
▶Before reaching into the device or the system, switch o the power
supply and secure to prevent reactivation! Observe the applicable
accident prevention and safety regulations for electrical devices.
Risk of burns or risk of re.
Continuous operation or hot media may result in a hot device
surface.
▶Keep the device away from highly ammable substances and
media and do not touch with bare hands!
▶Do not obstruct heat dissipation required for operation.
Risk of injury due to cold, hot and aggressive media.
Heat sources or temperature uctuations may cause malfunctions
or leaks.
▶Avoid heat sources which may cause the permissible tempera-
ture range to be exceeded.
▶Check the media resistance before use.
english
4
Danger due to low and high temperatures.
Depending on the media temperature, the device can become
extremely cold or extremely hot.
▶Keep the device away from substances sensitive to cold and
highly ammable substances and do not touch with bare
hands.
Destruction of the coil due to overheating
▶Electrically connect coil with mounted housing only.
▶In the case of alternating voltage, pay attention to movable
core.
▶Check media resistance.
General hazardous situations.
To prevent injuries, ensure that:
▶Do not feed in any aggressive or highly ammable media.
▶Do not make any internal or external changes to the device.
▶Secure the system and device against accidental activation.
▶Installation and maintenance may only be performed by autho-
rised technicians only using the appropriate tools.
▶After an interruption in the power or pneumatic supply, ensure
that the process is restarted in a dened or controlled manner.
▶Do not mechanically load housing.
▶Observe the general rules of technology.
4 TECHNICAL DATA
The following values are indicated on the type label:
•Voltage, current type, coil power
•Pressure range
•Body material (MS=brass, VA=stainless steel)
•Seal material (PTFE, NBR)
4.1 Conformity
The Type 6026 conforms to the EU directives as per the EU Declaration
of Conformity (if applicable).
4.2 Standards
The applied standards, which are used to demonstrate conformity with
EU directives, are listed in the EU type examination certicate and/or
the EU Declaration of Conformity (if applicable).
4.3 Operating conditions
Ambient temperature max. +50°C
Degree of protection with cable plug: IP65 acc. to EN 60529,
NEMA 4X
english
5
4.4 Electrical operating conditions
Relative duty cycle [%]
Ambient temperature [°C]
Switching frequency
Intermittent operation
characteristics for variant
with AC/DC high-perfor-
mance electronics
With AC/DC high-performance electronics
Operating mode
(acc. to DIN VDE 0580)
Continuous operation
Intermittent operation (To determine the per-
missible operating parameters, see “Chapter
4.4” and “Chapter 4.7”)
Minimum duty cycle
Minimum currentless
break
Switching time
1 s
1 s
approx. 500 ms
With AC/DC high-performance electronics
Maximum switching
frequency
Maximum relative duty
cycle
see “Diagram of electrical operating condi-
tions”
4.5 Fluidic data
Medium temperature –200...+180°C
viscosity 21mm²/s
Media neutral gaseous and liquid media that do not
attack the body and seal materials (see resis-
tance table: www.burkert.com). Check resis-
tance in each individual case.
Circuit function (CF)
Circuit function A
(NC)
1 (P)
2 (A)
2/2-way valve, 1 (P) normally
closed
english
6
4.6 Mechanical data
Port connections G¼, G½, G⅜
Materials
Body:
Identication MS Brass body, valve seat 1.4305
brass body, brass valve seat
Identication VA Body and valve seat 1.4410
Actuator: Epoxide
Seal material: PTFE
Dimensions see data sheet
4.7 Electrical data
Connections DIN EN 175301-803 Form A:
for cable plug Type 2508
Operating voltage see type label
Voltage tolerance ±10%
Nominal power 8W operation, 85W inrush
Switching frequency max. 10/min
O time toff between
2 switch-on procedures min. 1s
english
7
CE marking
Intermittent operation for variant with AC/DC high-performance
electronics
Characteristics (acc. to DIN VDE 0580)
tSD – cycle time
tED – duty cycle
tSP – currentless break
ED – relative duty
cycle
SH – switching
frequency
tED
tSP
tSD
tSD [s] = 60
SH 1
min
tED [s] =
tSP [s] = tSD [s] – tED [s]
ED[%]
100
x
tSD
[s]
4.8 Type label (example)
Identication number
Voltage, frequency, output
Connection,
pressure range
Type
Circuit function
Seat orice Seal material
Body material
english
8
5 INSTALLATION
DANGER!
Risk of injury from high pressure in the system.
▶Before loosening lines and valves, turn o the pressure and
drain the lines!
Risk of injury due to electric shock.
▶Before reaching into the system, switch o the power supply
and secure to prevent reactivation.
▶Observe the applicable accident prevention and safety regula-
tions for electrical devices.
WARNING!
Risk of injury due to improper installation.
▶Installation may be carried out by authorised technicians only
and with the appropriate tools.
Risk of injury due to unintentional activation of the system and
uncontrolled restart.
▶Secure the system against unintentional activation.
▶Following installation, ensure a controlled restart.
5.1 Fluid installation
Installation position: any, preferably coil or actuator face up.
→Clean pipelines and ange connections.
→Install dirt trap at the valve inlet (0.2...0.4 mm).
Note the ow direction of the valve. The arrow on the body
indicates the ow direction.
Arrow indicating
ow direction
NOTE!
Caution: Risk of breakage.
▶Do not use the coil or actuator as a lever arm.
Threaded connection:
→Hold the valve body using a matching open-end wrench and
screw into the pipeline.
english
9
5.2 Electrical installation
WARNING!
Risk of injury due to electric shock.
▶Before reaching into the system, switch o the power supply
and secure to prevent reactivation.
▶Observe the applicable accident prevention and safety regula-
tions for electrical devices.
If there is no protective conductor function between the coil and
body, there is a risk of electric shock.
▶Always connect protective conductor.
▶Check electrical continuity between coil and body.
Observe voltage and current type according to type label.
→Check that seal is correctly tted.
→Screw cable plug tightly onto the coil
(max. 1 Nm).
Only for variant with terminal connection box:
•Connect a maximum of one conductor per terminal point
•The maximum connection cable cross-section is 2.5 mm² / AWG 14
•Remove insulation on the wires to a maximum length of 6 mm
•Tighten the terminal screws with 0.25 Nm
•Close the housing lid properly and tighten the lock screw with 2 Nm
•Check the consistency of the protective conductor connection
12
3
Item Symbol Pin assignment
1L N + -
2N L - +
3PE
english
10
5.3 Rotating the solenoid
WARNING!
Risk of injury due to electric shock.
If there is no protective conductor function between the coil and
body, there is a risk of electric shock.
▶Check the protective conductor function after installing the coil.
Overheating, risk of re.
Connecting the coil without rst installing the valve will lead to
overheating and will destroy the coil.
▶Only connect the coil after the valve has been installed.
The coil can be rotated by 4 x 90°.
4 x 90°
Nut
(max. 5 Nm).
Valve
→Loosen nut.
→Rotate the solenoid.
→Use a matching open-end wrench to
tighten the nut (max. 5 Nm).
6 MAINTENANCE, TROUBLESHOOTING
WARNING!
Risk of injury due to improper maintenance work.
▶Maintenance may be carried out by authorised technicians only
and with the appropriate tools.
Risk of injury due to unintentional activation of the system and
uncontrolled restart.
▶Secure the system against unintentional activation.
▶Following maintenance, ensure a controlled restart.
Check in case of faults:
•Port connections
•Operating pressure
•Operating voltage
If the valve still does not switch, contact your local Bürkert Service
representative.
english
Inhaltsverzeichnis
Andere Burkert Steuereinheit Handbücher
Burkert
Burkert 623969 Bedienungsanleitung
Burkert
Burkert 6510 Bedienungsanleitung
Burkert
Burkert 6144 Bedienungsanleitung
Burkert
Burkert 2006 Bedienungsanleitung
Burkert
Burkert 2030 Bedienungsanleitung
Burkert
Burkert 5470 Bedienungsanleitung
Burkert
Burkert 2065 Bedienungsanleitung
Burkert
Burkert 2012 Bedienungsanleitung
Burkert
Burkert 0131 Bedienungsanleitung
Burkert
Burkert 3270 Bedienungsanleitung
Burkert
Burkert 2100 series Bedienungsanleitung
Burkert
Burkert 2301 Series Bedienungsanleitung
Burkert
Burkert 6724 Series Bedienungsanleitung
Burkert
Burkert 5470 Bedienungsanleitung
Burkert
Burkert 0142 Bedienungsanleitung
Burkert
Burkert 0340 Bedienungsanleitung
Burkert
Burkert 2031 Bedienungsanleitung
Burkert
Burkert 3364 Bedienungsanleitung
Burkert
Burkert Robolux 2036 Bedienungsanleitung
Burkert
Burkert EPS 21 ATEX 1 234 X Bedienungsanleitung
Beliebte Steuereinheit Handbücher anderer Marken
Festo
Festo Compact Performance CP-FB6-E Stücklistenhandbuch
Elo TouchSystems
Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung
JS Automation
JS Automation MPC3034A Bedienungsanleitung
JAUDT
JAUDT SW GII 6406 Series Kurzanleitung
Spektrum
Spektrum Air Module System Bedienungsanleitung
BOC Edwards
BOC Edwards Q Series Bedienungsanleitung
