Burkert 6126 Bedienungsanleitung
Bedienungsanleitung
Manuel d‘utilisation
Operating Instructions
Type 6126, Type 6606
Rocker solenoid valve
2/2 or 3/2-way solenoid valve
2/2 oder 3/2-Wege Magnetventil
Vanne magnétique 2/2 ou 3/2
2
1 THE OPERATING INSTRUCTIONS
The operating instructions contain important information.
▶Read the instructions carefully and follow the safety instructions
in particular.
▶Keep the instructions and provide them to every user.
▶The liability and warranty do not apply if the procedures in the
operating instructions are not followed.
1.1 Symbols
▶Highlights instructions to avoid a danger.
→Designates a procedure which you must carry out.
Warning of injuries:
DANGER!
Immediate danger! Serious or fatal injuries.
WARNING!
Possible danger! Serious or fatal injuries.
CAUTION!
Danger! Moderate or minor injuries.
Warning of damage:
NOTE!
Table of contents
1 The operating instructions.......................................................... 2
2 Intended use.............................................................................. 3
3 Basic Safety Instruction ............................................................. 3
4 General Information.......................................................................5
5 System Description.................................................................... 6
6 Technical Data ........................................................................... 7
7 Installation ...................................................................................10
8 Maintenance, Troubleshooting ................................................. 17
9 Spare parts.............................................................................. 18
10 Packaging, Transport, Storage................................................. 19
11 Disposal................................................................................... 19
english
3
2 INTENDED USE
Non-intended use of the solenoid valves Type 6126 and Type
6606 can be dangerous to people, nearby equipment and the
environment.
▶The solenoid valves Type 6126 and Type 6606 are designed for
use in analytical, medical and laboratory technology. They can
be used primarily for the metering, lling, mixing and distribution
of small amounts.
▶Do not use the device outdoors.
▶Use according to the authorized data, operating conditions
and conditions of use specied in the contract documents and
operating instructions. These are described in the chapter enti-
tled ““6 Technical Data””.
▶The device may be used only in conjunction with third-party
devices and components recommended and authorized by
Bürkert.
▶Correct transportation, correct storage and installation and
careful use and maintenance are essential for
reliable and faultless operation.
▶Use the device only as intended.
3 BASIC SAFETY INSTRUCTION
These safety instructions do not make allowance for any contin-
gencies and events which may arise during the installation, oper-
ation and maintenance of the devices.
DANGER!
Danger – high pressure!
▶Before loosening the lines and valves, turn o the pressure and
vent the lines.
Risk of electric shock!
▶Before reaching into the device or the equipment, switch o
the power supply and secure to prevent reactivation!
▶Observe applicable accident prevention and safety regulations
for electrical equipment!
Risk of burns/risk of re if used continuously through hot
device surface!
▶Keep the device away from highly ammable substances and
media and do not touch with bare hands.
english
4
WARNING!
Leaking medium when the diaphragm is worn.
▶Regularly check for leaking medium.
▶If the media is hazardous, protect the environment from danger.
General hazardous situations.
To prevent injury, ensure that:
▶The system cannot be activated unintentionally.
▶Installation and repair work may be carried out by authorized
technicians only and with the appropriate tools.
▶After an interruption in the power supply or pneumatic supply,
ensure that the process is restarted in a dened or controlled
manner.
▶The device may be operated only when in perfect condition and
in consideration of the operating instructions.
▶The general rules of technology apply to application planning
and operation of the device.
NOTE!
Electrostatic sensitive components / modules!
The device contains electronic components which react sensitively
to electrostatic discharge (ESD). Contact with electrostatically
charged persons or objects is hazardous to these components.
In the worst case scenario, they will be destroyed immediately or
will fail after start-up.
•Observe the requirements in accordance with
EN 61340-5-1 and 5-2 to minimise or avoid the possibility of
damage caused by sudden electrostatic discharge!
•Also ensure that you do not touch the electronic components
when the power supply voltage is present!
The solenoid valves Type 6126 and Type 6606 were developed
with due consideration given to the accepted safety rules and are
state-of-the-art. Nevertheless, dangerous situations may occur.
Failure to observe this operating manual and its operating instruc-
tions as well as unauthorised tampering with the device release
us from any liability and also invalidte the warranty covering the
device and accessories!
english
5
4 GENERAL INFORMATION
4.1 Scope of Supply
Check immediately upon receipt of the delivery that the contents are
not damaged and that the type and scope agree with the delivery note
and packing list.
If there are any discrepancies, please contact us immediately.
Germany
Contact address:
Bürkert Fluid Control Systems
Sales Center
Chr.-Bürkert-Str. 13-17
D-74653 Ingelngen
Tel.: + 49 (0) 7940 - 10 91 111
Fax: + 49 (0) 7940 - 10 91 448
E-mail: [email protected]
International
Contact addresses can be found on the final pages of the printed oper-
ating instructions.
And also on the internet at:
www.burkert.com Bürkert Company Locations
4.2 Warranty
This document contains no promise or guarantee. Please refer to
our general terms of sales and delivery. The warranty is only valid
if the device is used as intended in accordance with the specied
application conditions.
The warranty extends only to defects in the solenoid valves
Type6126 and Type6606 and their components.
We accept no liability for any kind of collateral damage
which could occur due to failure or malfunction of the
device.
4.3 Approvals
The approval rating on the Bürkert lables concerns to Bürkert
products.
Devices that carry the e1 marking have been approved by the
Federal Oce for Motorised Transport under the type approval
number
e1*72/245*2006/96*5791*00
and will be brought into circulation with the indicated approval
designation.
english
6
You can obtain an excerpt from the type approval from the address
below
Bürkert Werke GmbH & Co KG
Zulassungsbeauftragter
Christian-Bürkert-Str.13-17
D-74653 Ingelngen
4.4 Information on the Internet
Operating instructions and data sheets for Types 6126 and 6606
can be found on the Internet at:
www.burkert.com Documentation Type
5 SYSTEM DESCRIPTION
5.1 Intended Application Area
The solenoid valves Type 6126 and Type 6606 are designed for use
in analytical, medical and laboratory technology. They can be used
primarily for the metering, lling, mixing and distribution of small
amounts.
5.2 General Description
The solenoid valves Type 6126 and Type 6606 are direct-acting
rocker solenoid valves. They have a minimum dead volume and
a non-split, easy-to-rinse inner contour. The medium comes into
contact with the body material and the seals only. The heat transfer
into the medium is minimal, as the body is also separated from the
coil by a stainless steel plate.
Modularity
The valve is modular in design and can be supplied with dierent
port connections according to the application case. It can be used
individually and also in blocks.
english
7
6 TECHNICAL DATA
6.1 Operating Conditions
WARNING!
Risk of injury
Malfunction if used outside!
▶Do not use Type 6126 and Type 6606 outdoors and avoid heat
sources which may cause the allowable temperature range to
be exceeded.
Allowable temperatures
Ambient temperature: max. +55 °C
Medium temperature: -5... +50 °C
Media: neutral and aggressive, gaseous and liquid
media which do not attack body and seal
materials
see Bürkert Chemical Resistance Chart
(www.burkert.com)
Protection class: IP65 with ying leads or cable plug
IP40 with rectangular plug
6.2 Conformity
CE mark conforms to EMC Directive 2004/108/EEC
(only if cables, plugs and sockets connected correctly).
6.3 Mechanical data
Dimensions See data sheet
Body material PPS, PVDF, ETFE, PEEK
Brass, stainless steel
Seal material FKM, FFKM, EPDM
english
8
6.4 Pneumatic data
Circuit functions
A
A
P/NC
2/2-way valve, direct-acting, normally
closed
B
B
P/NO
2/2-way valve, direct-acting, normally
open
T
A in/out
P/NC R/NO
3/2-way valve, direct-acting,
universal function
Note the information specied on the label for voltage, type
of current, and pressure.
Pressure range Vac ... 2 bar
Port connections Threaded connection G1/8, M5
NPT1/8 or UNF1/4-28
Flange connection
Tube hose connection
6.5 Label
Example:
Made in Germany
00450000 W14UN
6606 T 1,6 FKM PD
G1/8 PNVAK-2bar
24V DC 3,4W
Identication number
Voltage/frequency output
Nominal connection pressure
Type
Circuit function
Orice
Seal material
Body material
english
9
6.6 Electrical Data
Connections: Spade connection in accordance with DIN
43650 C for cable plug
Type 2516 on top or on side
Rectangular plug for Type 2505
2 FEP ying leads, AWG24,
500 mm long
Power supply: 12 V DC
24 V DC
110 – 120 V UC
230 – 240 V UC
Voltage tolerance ±10 % - Residual ripple 10 %
Nominal output
12 – 24 V 3.4 W
110 – 240 V 4.0 W
Nominal
operating mode 100 % continuous operation
for block installation if temperatures of media or
surrounding area above +40 °C:
Intermittent duty 40 % (10 min)
Note the information specied on the label for voltage, type
of current, and pressure.
english
10
7 INSTALLATION
7.1 Safety instructions
DANGER!
Risk of injury from high pressure in the equipment!
▶Before loosening the lines and valves, turn o the pressure and
vent the lines.
Risk of injury due to electrical shock!
▶Before reaching into the device or the equipment, switch o the
power supply and secure to prevent reactivation!
▶Observe applicable accident prevention and safety regulations for
electrical equipment!
WARNING!
Risk of injury from improper installation!
▶Installation may be carried out by authorized technicians only and
with the appropriate tools!
Risk of injury from unintentional activation of the system and
an uncontrolled restart!
▶Secure system from unintentional activation.
▶Following installation, ensure a controlled restart.
7.2 Fluid Installation
DANGER!
Risk of injury from high pressure in the equipment!
▶Before loosening the lines and valves, turn o the pressure and
vent the lines.
Installation position: any, actuator preferably upwards.
Installation
Before installation, clean any possible dirt o the pipelines and
ange connections.
→If required, install a dirt trap to prevent malfunctions.
Mesh size: 5 µm
Pay attention to the ow direction of the valve.
english
Andere Handbücher für 6126
1
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Sprachen:
Andere Burkert Steuereinheit Handbücher
Burkert
Burkert 2100 series Bedienungsanleitung
Burkert
Burkert 6517 Bedienungsanleitung
Burkert
Burkert 5420 Bedienungsanleitung
Burkert
Burkert 0250 Bedienungsanleitung
Burkert
Burkert 0262 Bedienungsanleitung
Burkert
Burkert 8791 REV.2 Bedienungsanleitung
Burkert
Burkert 3320 Bedienungsanleitung
Burkert
Burkert 6650 Bedienungsanleitung
Burkert
Burkert 2610 Bedienungsanleitung
Burkert
Burkert 2030 Bedienungsanleitung
Burkert
Burkert 8630 Bedienungsanleitung
Burkert
Burkert Type 2000 Bedienungsanleitung
Burkert
Burkert 3270 Bedienungsanleitung
Burkert
Burkert 8640 Bedienungsanleitung
Burkert
Burkert 3281 Bedienungsanleitung
Burkert
Burkert 0124 Bedienungsanleitung
Burkert
Burkert 2300 Series Bedienungsanleitung
Burkert
Burkert 2065 Bedienungsanleitung
Burkert
Burkert 2103 Series Bedienungsanleitung
Burkert
Burkert 2060 Bedienungsanleitung
Beliebte Steuereinheit Handbücher anderer Marken
Festo
Festo Compact Performance CP-FB6-E Stücklistenhandbuch
Elo TouchSystems
Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung
JS Automation
JS Automation MPC3034A Bedienungsanleitung
JAUDT
JAUDT SW GII 6406 Series Kurzanleitung
Spektrum
Spektrum Air Module System Bedienungsanleitung
BOC Edwards
BOC Edwards Q Series Bedienungsanleitung
