Bushnell 32-3940B Bedienungsanleitung
A
DOA 6LIM.indd 1 1/5/09 12:02:20 PM
1
GENERAL INSTRUCTIONS
The DOA reticle gives hunters a series of aiming points that correspond to various black powder and centerfire loads.
These aiming points, combined with our innovative Rack Bracket, allows hunters to expand their effective range
while also aiding in field judging whitetail or mule deer at extended distances. Bushnell would like to stress
that these tools are only as good as the time spent practicing with them. Nothing can replace
quality firing range time and becoming comfortable shooting at each of the prescribed yardages, while noting bullet
placement. It is imperative for the hunter to spend time at the range, gaining familiarity with the reticle and how
it works with their firearm and bullet load. Ballistic performance can vary depending upon a number of factors,
including barrel length, powder type, bullet type, and numerous weather/atmosphere related variables.
THE DOA 250 RETICLE – For Muzzleloaders
Scopes with the DOA 250 are designed to be sighted-in at 100 yds, with aiming points every 50 yds, out to 250
yds. The top of the reticle’s bottom post represent approximately 300 yds. The shooter can use either .45 or .50
cal ammunition, and either 100 grains or 150 grains of Triple 7 pellets. The ballistic chart provided below is an
abbreviated version of the more complete one available online at: http://www.bushnell.com/customer_service/
manuals/rifle.cfm.
The scope must also be set to the proper magnification for the reticle’s ballistic feature to function properly. In the
case of a 3-9x 40mm scope, the power change ring must be set at 9x for the ballistic function and Rack Bracket
to work correctly.
ENGLISH
DOA 6LIM.indd 2 1/5/09 12:02:20 PM
2
DOA 250
In-Line Muzzleloaders
Based on a 100-yard zero
and the ballistics of the most
common magnum loads for
in-lines.
150 yds.
200 yds.
250 yds.
DOA 6LIM.indd 3 1/5/09 12:02:21 PM
3
How To Use the Reticle:
1. Sight in at 100 yds on any magnification setting
2. Determine distance to target. For the best accuracy in determining distance, utilize a Bushnell Laser
Rangefinder (Scout 1000 ARC, Legend 1200 ARC).
3. Set the scope’s magnification to 9x (9 power).
4. Place the appropriate aiming point on the desired target. If the target was determined to be at 175 yds,
hold directly between the 150 yd aiming point and the 200 yd aiming point.
100 yd Sight-In 150 yd Sight-In
150 yd
Mark
200 yd
Mark
250 yd
Mark
300 yd
Mark
150 yd
Mark
200 yd
Mark
250 yd
Mark
300 yd
Mark
.45 cal 225 gr HP Copper Clad BC=.176 100 grains 150 200 250 300 180 225 275 300
.45 cal 225 gr HP Copper Clad BC=.176 150 grains 150 200 250 300 180 225 275 300
.50 cal 245 gr HP Copper Clad BC=.140 150 grains 150 200 250 300 180 225 275 300
.50 cal 295 gr HP Copper Clad BC=.168 150 grains 150 200 250 300 180 225 275 300
.50 cal 348 gr HP Copper Clad BC=.198 150 grains 150 200 250 300 180 225 275 300
.45 cal 225 gr Copper Clad AeroTip BC=.211 150 grains 150 200 250 300 180 225 275 300
.45 cal 275 gr Copper Clad AeroTip BC=.258 150 grains 150 200 250 300 180 225 275 300
.45 cal 300 Platinum AeroTip BC=.278 100 grains 150 200 250 300 180 225 275 300
.50 cal 223 gr Copper Clad AeroTip BC=.142 150 grains 150 200 250 300 180 225 275 300
.50 cal 245 gr Copper Clad AeroTip BC=.161 150 grains 150 200 250 300 180 225 275 300
.50 cal 270 Platinum AeroTip BC=.192 150 grains 150 200 250 300 180 225 275 300
.50 cal 295 gr Copper Clad AeroTip BC=.186 100 grains 150 200 250 300 180 225 275 300
.50 cal 295 gr Copper Clad AeroTip BC=.186 150 grains 150 200 250 300 180 225 275 300
.50 cal 300 gr Platinum AeroTip BC=.214 150 grains 150 200 250 300 180 225 275 300
DOA 6LIM.indd 4 1/5/09 12:02:21 PM
4
100 yd Sight-In 150 yd Sight-In
150 yd
Mark
200 yd
Mark
250 yd
Mark
300 yd
Mark
150 yd
Mark
200 yd
Mark
250 yd
Mark
300 yd
Mark
.45 cal 225 gr HP Copper Clad BC=.176 100 grains 150 200 250 300 180 225 275 300
.45 cal 225 gr HP Copper Clad BC=.176 150 grains 150 200 250 300 180 225 275 300
.50 cal 245 gr HP Copper Clad BC=.140 150 grains 150 200 250 300 180 225 275 300
.50 cal 295 gr HP Copper Clad BC=.168 150 grains 150 200 250 300 180 225 275 300
.50 cal 348 gr HP Copper Clad BC=.198 150 grains 150 200 250 300 180 225 275 300
.45 cal 225 gr Copper Clad AeroTip BC=.211 150 grains 150 200 250 300 180 225 275 300
.45 cal 275 gr Copper Clad AeroTip BC=.258 150 grains 150 200 250 300 180 225 275 300
.45 cal 300 Platinum AeroTip BC=.278 100 grains 150 200 250 300 180 225 275 300
.50 cal 223 gr Copper Clad AeroTip BC=.142 150 grains 150 200 250 300 180 225 275 300
.50 cal 245 gr Copper Clad AeroTip BC=.161 150 grains 150 200 250 300 180 225 275 300
.50 cal 270 Platinum AeroTip BC=.192 150 grains 150 200 250 300 180 225 275 300
.50 cal 295 gr Copper Clad AeroTip BC=.186 100 grains 150 200 250 300 180 225 275 300
.50 cal 295 gr Copper Clad AeroTip BC=.186 150 grains 150 200 250 300 180 225 275 300
.50 cal 300 gr Platinum AeroTip BC=.214 150 grains 150 200 250 300 180 225 275 300
DOA 6LIM.indd 5 1/5/09 12:02:21 PM
5
THE DOA 600 RETICLE – For Centerfire Rifles
Designed to be used with today’s most popular centerfire rifle cartridges, the DOA 600 reticle is intended to be
sighted in at 100 yards, and provides aiming points at every 100 yd increment, out to 600 yds. The user can
sight-in at 100 yds on any magnification setting, but for the ballistic reticle feature to function properly, the scope’s
magnification must be set to the correct power. The correct settings for the scopes that include the DOA reticle are
as follows:
If your scope is a: Use this power setting:
3-9x 40 9x
4-12x 40 12x
2.5-16x 42 16x
4.5-30x 50 20x
DOA 6LIM.indd 6 1/5/09 12:02:21 PM
6
DOA 600
Centerfire Rifles
Based on a 100-yard zero
and the ballistics of the most
common magnum loads for
in-lines.
With MOA dots as the
long-range aiming points,
the DOA offers a higher level
of precision than competing
extended-yardage reticles.
200 yds.
300 yds.
400 yds.
500 yds.
650 yds.
DOA 6LIM.indd 7 1/5/09 12:02:23 PM
7
How To Use the Reticle:
1. Sight in at 100 yds on any magnification setting
2. Determine distance to target. For the best accuracy in determining distance, utilize a Bushnell
Laser Rangefinder (Scout 1000 ARC, Legend 1200 ARC).
3. Set the magnification to the appropriate setting.
4. Place appropriate aiming point on the desired target. If the target is determined to be at 350 yds,
hold directly between the 300 yd aiming point and the 400 yd aiming point
The DOA 600 reticle will work with any of the following ammunition loads:
.223 Win 55 gr
.243 Win, 95 gr.
. 25-06 Rem 115 gr
.270 Win, 130 gr.
. 270 WSM, 150 gr.
.7mm Rem Mag, 150 gr.
.7mm WSM, 150 gr.
.30-06 Sprg, 150 gr.
.300 Winchester Mag, 180 gr.
.300 WSM, 180 gr.
.338 Win, 200 gr.
DOA 6LIM.indd 8 1/5/09 12:02:23 PM
8
This is only a partial list of the ammunition that the reticle is ballistically matched to. For a complete list of all
ammunition compatible with the DOA 600 reticle technology, please visit:
http://www.bushnell.com/customer_service/manuals/rifle.cfm
HOW THE RACK BRACKET WORKS
In an effort to help hunters, Bushnell looked at issues that had confronted many of them in the field. Field judging
deer, especially via magnified view, can be exceedingly difficult. To help with the field judging of whitetails and
mule deer we have incorporated a series of lines that extend out from each aiming point. Each lines measures
24 inches at the respective distance. There will also be two “hash marks” on each line that measure 17 inches
between them. Why did we choose 24” and 17”? After extensive research it was determined that 24 inches rep-
resents the average width of a mule deer’s ears and 17 inches was the average width of a whitetail’s ears. Given
proper time to judge an animal, a hunter can now get an estimate of rack width, and possibly even tine length.
Rack Bracket estimations are for reference only and may not be exact. Make note that it is the sole responsibility of
the hunter to make the final determination on any animal they decide to harvest. Please refer to your local
and/or state regulations regarding antler width standards for harvested animals. It is the
hunters responsibility to be knowledgeable of and abide by all game regulations.
DOA 6LIM.indd 9 1/5/09 12:02:23 PM
9
The Rack Bracket System
Size him up and put him down with the Rack Bracket.
Based on scope set at highest
power. For example, a 3-9x
scope would need to be at
9x for Rack Bracket accuracy.
24" – All extended yardage
crosshairs measure 24," the
tip-to-tip distance between
an average mule deer’s ears.
Judgement – Use the 24" and
17" measurements to gauge the
buck’s width. If the ears fit,
you have an accurate
estimation of range.
17" – The hash marks on each
extended-yardage crosshair
indicate the distance between
an average whitetail’s ears.
DOA 6LIM.indd 10 1/5/09 12:02:24 PM
Dieses Handbuch passt für folgende Modelle
7
Inhaltsverzeichnis
Sprachen:
