C.A. Technologies Jaguar 300H Bedienungsanleitung
HVLP AIR CAP AND FLUID NOZZLE CHART
MODEL
NO. AIR CAPS
*MAX GUN
INLET PRESS.
FOR HVLP
FAN
CONTROL
SCFM @
MAX GUN
INLET
AIR CAP
RING
AVAI LABLE FLUI D
NOZZLES TIPS
NEEDLES /
marking on needle
23-1008 40** 13.5 33-0208 0.8mm (.022") 40-1308 (308)
23-1010 40** 13.5 33-0210 1.0mm (.040") 40-1310 (310)
23-1012 40** 13.5 33-0212 1.2mm (.046") 40-1312 (312)
23-1013 40** 13.5 33-0213 1.3mm (.052") 40-1313 (313)
23-1014 40** 13.5 33-0214 1.4mm (.055") 40-1314 (314)
23-1015 40** 13.5 33-0215 1.5mm (.059") 40-1315 (315)
23-1017 40** 13.5 33-0217 1.7mm (.070") 40-1317 (317)
23-1019 40** 13.5 33-0219 1.9mm (.075") 40-1319 (319)
23-1022 40** 13.5 33-0222 2.2mm (.086") 40-1322 (322)
Actual fluid nozzle and air cap combinations are determined by application (see application chart page 4)
*Note: Air cap test gages are available to confirm HVLP compliance.
*Gun inlet pressures may vary as required by application
**When using optional gun regulator, inlet pressure changes to 45psi
IncludedJ300H 60-1502 (#2)
GRAVITY FEED SPRAY GUN
PRODUCT INFORMATION
Coating Atomization Technologies 337 South Arthur Avenue, Louisville CO 80027 Phone: 888.820.4498, Fax: 303.438.5708
www.spraycat.com
Jaguar 300HJaguar 300H
Jaguar 300HJaguar 300H
Jaguar 300H
Operation and Maintenance Instructions for
J300HJ300H
J300HJ300H
J300H
Spray Guns
Operation
1. Connect air supply hose at handle of gun.
2. Screw the paint cup onto the gun’s gravity feed fluid inlet.
3. Fluid flow can be controlled using the fluid control knob, this restricts flow by limiting needle travel. It is best to control
fluid flow by proper selection of fluid orifice size and use the fluid control knob to “fine tune flow rate”.
4. Fan width can be adjusted using the fan control knob. Turning the knob clockwise narrows the fan.
Maintenance
IMPORTANT! Routine cleaning and maintenance is essential to insure proper gun operation.
Several states prohibit spraying solvent into the atmosphere and require the use of covered gun cleaner.
1. If a gun cleaner is being used, connect and clean the gun in the gun cleaner according to the manufactures
instructions.
2. If a gun cleaner is not being used:
Remove air cap and clean separately using clean solvent.
Clean the gravity feed cup thoroughly, then spray clean solvent through the gun until clean.
NOTE: Gun head disassembly is not recommended for normal cleaning and maintenance.
Gun head disassembly and reassembly instructions:
Have repair kit # 10-105 available before gun disassembly.
Gun head disassembly
To remove the nozzle carrier (5) and air cap adapter (7):
1. Remove the air cap (1), fluid nozzle tip (2), fluid nozzle body (3), and needle (16).
2. Remove the needle seal cartridge (17).
3. Loosen the locknut (11) and remove fluid inlet (12) using a 11/16” open-end wrench.
4. The nozzle carrier (5) and air cap adapter (7) will now slide forward from the gun body (13).
Gun head reassembly
1. Install a new o-ring (4 & 8) on the air cap adapter (7).
2. Install the thread locknut (11) and seal (10) onto the fluid inlet (12) as far as possible.
3. Install a new fluid inlet seal (9) into the recess area on the nozzle carrier (5) inlet port.
4. Install carrier seal (6) onto the back of the nozzle carrier (5).
5. Slide the nozzle carrier (5) into air cap adapter (7) and insert into the gun body (13) as far as possible. Be sure the
nozzle carrier (5) extends into the hole at the back of the gun head. Install the needle seal (17) but do not tighten.
6. Rotate the nozzle carrier (5) until the fluid inlet port in the nozzle carrier (5) is aligned with the threaded hole in the
body. While in this position, insert the fluid inlet (12) and tighten firmly.
7. Tighten the needle seal (17) to approx. 12 ft.-lb. torque.
8. Tighten the fluid inlet (12) to approx. 25 ft.-lb. torque.
9. Tighten the locknut (11) to approx. 33 ft.-lb. torque.
*
*
*
*
*
*
*
*
*
*
*
ITEM NO. PART NO. DESCRIPT ION IT EM NO. PART NO. DESCRIPT ION
1 See Air Cap Chart Air Cap** 19 60-2101 Trigger
2 See Air Cap Chart Fluid Tip** 20 60-1520 Air Valve Assembly
3 33-1201 Fluid Nozzle Body 21 60-302 Air Valve Poppet
4 98-8026 O-Ring* 22 60-125 Seal*
5 60-J31H Nozzle Body Carrier 23 61-1003 Air Valve Spring*
6 60-123 Seal* 24 60-119 Seal*
7 60-34H Air Cap Adapter 25 60-201 Rear Bushing
8 60-131 O-Ring* 26 60-204 Needle Return Spring*
9 60-124 Seal* 27 60-205 Spring Seat*
10 60-130 Seal* 28 60-202 Fluid Control Knob*
11 60-118 Locknut 29 60-1510 Inlet Air Control (Optional)
12 60-127 Fluid Inlet 30 60-122 Plug
13 60-1113 Jaguar Gun Body HVLP 31 60-104 Air Inlet Fitting
14 98-0109 Allen Plug 51-401 Standard 700 mL Gravity Feed Cup (Aluminum)
15 See Air Cap Chart Fan Control Assembly** 51-400 Optional 700 mL Gravity Feed Cup (Plastic)
16 See Air Cap Chart Fluid Needle** 51-403 Optional 1000 mL Gravity Feed Cup (Aluminum)
17 60-1400 Needle Seal* 51-418 Gravity Cup Lid (401 & 403)
18 60-1033 Trigger Pivot Set 51-413 Gravity Cup Lid (400)
**See air cap selection chart on page 1
*Indicates part included in repair kit # 10-105
32
33
HVLP AIR CAP TEST GAGES
23-1008-G
23-1010-G
23-1012-G
FOR
J300H
GUNS
23-1013-G
23-1014-G
23-1015-G
23-1022-G
23-1017-G
23-1019-G
J300H HVLP SPRAY GUN
MATERIAL TYPE FLUID ORIFICE x
AI R C AP
MAXIMUM
PATTERN WIDTH CFM
Very Thin
less than 16 sec. Zahn #2
inks , dyes,
solvents, stains
Thin
16 to 20 sec. Zahn #2
lacquers, enamels,
primers, sealers
Medium
21 to 30 sec. Zahn #2
automotive base coat
enamels, primers
epoxies, urethanes
automotive clear coat
Heavy
over 30 sec. Zahn #2
heavy body primers
high solid enamels
high solid automotive coatings
adhesives
1.5 mm x 1015
1.7 mm x 1017
1.9 mm x 1019
2.2 mm x 1022
12
12
12
12
13.5
13.5
13.5
13.5
FLUID NOZZLE / AIR CAP SELECTION CHARTS
JAGUAR Series 300H - Gravity Feed Guns
1.0 mm x 1010 12 13.5
1.0 mm x 1010
1.3 mm x 1013
12
12
13.5
13.5
1.3 mm x 1013
1.5 mm x 1015
1.7 mm x 1017
12
12
12
13.5
13.5
13.5
Revised 3/18/14
Andere C.A. Technologies Spritzpistole Handbücher
C.A. Technologies
C.A. Technologies FE-Line Fine Finish Bedienungsanleitung
C.A. Technologies
C.A. Technologies JAGUAR SLP Bedienungsanleitung
C.A. Technologies
C.A. Technologies Lynx 300H Bedienungsanleitung
C.A. Technologies
C.A. Technologies AutoCAT 100CVT Bedienungsanleitung
C.A. Technologies
C.A. Technologies Lynx 100 Series Bedienungsanleitung
C.A. Technologies
C.A. Technologies Panther 200H Bedienungsanleitung
C.A. Technologies
C.A. Technologies Lynx 100CM Bedienungsanleitung
C.A. Technologies
C.A. Technologies Lynx L100C Bedienungsanleitung
C.A. Technologies
C.A. Technologies CPR Bedienungsanleitung
C.A. Technologies
C.A. Technologies Lynx 300C Fehlerbehebungshandbuch
C.A. Technologies
C.A. Technologies Panther 100G 1590 Bedienungsanleitung
C.A. Technologies
C.A. Technologies Lynx 100CVT Bedienungsanleitung
C.A. Technologies
C.A. Technologies TOMCAT 100C Fehlerbehebungshandbuch
C.A. Technologies
C.A. Technologies AutoCAT 100C Bedienungsanleitung
C.A. Technologies
C.A. Technologies Lynx 100C Bedienungsanleitung
C.A. Technologies
C.A. Technologies H2O-CPR Bedienungsanleitung
C.A. Technologies
C.A. Technologies Tomcat Series Bedienungsanleitung
C.A. Technologies
C.A. Technologies CAT-Xpress Fehlerbehebungshandbuch
C.A. Technologies
C.A. Technologies Panther 200Z Bedienungsanleitung
C.A. Technologies
C.A. Technologies Jaguar 300 Series Bedienungsanleitung
