Cabletron Systems BRIM-E6 Bedienungsanleitung

BRIM-E6

USER’S GUIDE

CABLETRON SYSTEMS, P. O. Box 5005, Rochester, NH 03866-5005

BRIM-E6 USER’S GUIDE

NOTICE

Cabletron Systems reserves the right to make changes in speciﬁcations and other

information contained in this document without prior notice. The reader should in all cases

consult Cabletron Systems to determine whether any such changes have been made.

The hardware, ﬁrmware, or software described in this manual is subject to change without

notice.

IN NO EVENT SHALL CABLETRON SYSTEMS BE LIABLE FOR ANY

INCIDENTAL, INDIRECT, SPECIAL, OR CONSEQUENTIAL DAMAGES

WHATSOEVER (INCLUDING BUT NOT LIMITED TO LOST PROFITS) ARISING

OUT OF OR RELATED TO THIS MANUAL OR THE INFORMATION CONTAINED

IN IT, EVEN IF CABLETRON SYSTEMS HAS BEENADVISED OF, KNOWN, OR

SHOULD HAVE KNOWN, THE POSSIBILITY OF SUCH DAMAGES.

Cabletron Systems, Inc., P.O. Box 5005, Rochester, NH 03866-5005

Printed in the United States of America

Part Number: 9031027August 1994

LANVIEW

is a registered trademark of Cabletron Systems, Inc.

MicroMMAC

and

BRIM

are trademarks of Cabletron Systems, Inc.

Windows

is a registered trademark of Microsoft Corp.

Ethenet

is a trademark of Xerox Corp.

CompuServe

is a registered trademark of CompuServe

Printed On Recycled Paper

NOTICE

BRIM-E6 USER’S GUIDE

FCC NOTICE

This device complies with Part 15 of the FCC rules. Operation is subject to the following

two conditions: (1) this device may not cause harmful interference, and (2) this device

must accept any interference received, including interference that may cause undesired

operation.

NOTE:

This equipment has been tested and found to comply with the limits for a ClassA

digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide

reasonable protection against harmful interference when the equipment is operated in a

commercial environment. This equipment uses, generates, and can radiate radio frequency

energy and if not installed in accordance with the operator’s manual, may cause harmful

interference to radio communications. Operation of this equipment in a residential area is

likely to cause interference in which case the user will be required to correct the

interference at his own expense.

WARNING:

Changes or modiﬁcations made to this device which are not expressly

approved by the party responsible for compliance could void the user’s authority to

operate the equipment.

DOC NOTICE

This digital apparatus does not exceed the ClassA limits for radio noise emissions from

digital apparatus set out in the Radio Interference Regulations of the Canadian

Department of Communications.

Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les limites

applicables aux appareils numériques de la class A prescrites dans le Règlement sur le

brouillage radioélectrique édicté par le ministère des Communications du Canada.

NOTICE

BRIM-E6 USER’S GUIDE

iii

CABLETRON SYSTEMS, INC.

PROGRAM LICENSE AGREEMENT

IMPORTANT

: Before utilizing this product, carefully read this License Agreement.

This document is an agreement between you, the end user, and Cabletron Systems, Inc.

(“Cabletron”) that sets forth your rights and obligations with respect to the Cabletron

software program (the “Program”) contained in this package. The Program may be

contained in ﬁrmware, chips or other media. BY UTILIZING THE ENCLOSED

PRODUCT,YOU ARE AGREEING TO BECOME BOUND BY THE TERMS OF THIS

AGREEMENT, WHICH INCLUDES THE LICENSEAND THE LIMITATION OF

WARRANTY AND DISCLAIMER OF LIABILITY. IFYOU DO NOT AGREE TO THE

TERMS OF THISAGREEMENT, PROMPTLY RETURN THE UNUSED PRODUCT

TO THE PLACE OF PURCHASE FOR A FULL REFUND.

CABLETRON SOFTWARE PROGRAM LICENSE

1. LICENSE. You have the right to use only the one (1) copy of the Program provided

in this package subject to the terms and conditions of this License Agreement.

You may not copy, reproduce or transmit any part of the Program except as permitted by

the Copyright Act of the United States or as authorized in writing by Cabletron.

2. OTHER RESTRICTIONS. You may not reverse engineer, decompile, or

disassemble the Program.

3. APPLICABLE LAW. This License Agreement shall be interpreted and governed

under the laws and in the state and federal courts of New Hampshire.You accept the

personal jurisdiction and venue of the New Hampshire courts.

EXCLUSION OFWARRANTY AND DISCLAIMER OF

LIABILITY

1. EXCLUSION OF WARRANTY. Except as may be speciﬁcally provided by

Cabletron in writing, Cabletron makes no warranty, expressed or implied, concerning the

Program (including Its documentation and media).

CABLETRON DISCLAIMS ALL WARRANTIES, OTHER THAN THOSE SUPPLIED

TOYOU BY CABLETRON IN WRITING, EITHER EXPRESS OR IMPLIED,

INCLUDING BUT NOT LIMITED TO IMPLIED WARRANTIES OF

MERCHANTABLITY AND FITNESS FOR A PARTICULAR PURPOSE, WITH

RESPECT TO THE PROGRAM, THE ACCOMPANYING WRITTEN MATERIALS,

AND ANY ACCOMPANYING HARDWARE.

NOTICE

BRIM-E6 USER’S GUIDE

2. NO LIABILITY FOR CONSEQUENTIAL DAMAGES. IN NO EVENT SHALL

CABLETRON OR ITS SUPPLIERS BE LIABLE FOR ANY DAMAGES

WHATSOEVER (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF

BUSINESS, PROFITS, BUSINESS INTERRUPTION, LOSS OF BUSINESS

INFORMATION, SPECIAL, INCIDENTAL, CONSEQUENTIAL, OR RELIANCE

DAMAGES, OR OTHER LOSS) ARISING OUT OF THE USE OR INABILITY TO

USE THIS CABLETRON PRODUCT, EVEN IF CABLETRON HAS BEEN ADVISED

OF THE POSSIBILITY OF SUCH DAMAGES. BECAUSE SOME STATES DO NOT

ALLOW THE EXCLUSION OR LIMITATION OF LIABILITY FOR

CONSEQUENTIAL OR INCIDENTAL DAMAGES, OR ON THE DURATION OR

LIMITATION OF IMPLIED WARRANTEES IN SOME INSTANCES THE ABOVE

LIMITATIONSAND EXCLUSIONS MAY NOT APPLY TOYOU.

UNITED STATES GOVERNMENT RESTRICTED RIGHTS

The enclosed product (a) was developed solely at private expense; (b) contains “restricted

computer software” submitted with restricted rights in accordance with Section 52227-19

(a) through (d) of the Commercial Computer Software - Restricted Rights Clause and its

successors, and (c) in all respects is proprietary data belonging to Cabletron and/or its

suppliers.

For Department of Defense units, the product is licensed with “Restricted Rights” as

deﬁned in the DoD Supplement to the Federal Acquisition Regulations, Section 52.227-

7013 (c) (1) (ii) and its successors, and use, duplication, disclosure by the Government is

subject to restrictions as set forth in subparagraph (c) (1) (ii) of the Rights in Technical

Data and Computer Software clause at 252.227-7013. Cabletron Systems, Inc., 35

Industrial Way. Rochester, New Hampshire 03867

BRIM-E6 USER’S GUIDE

TABLE OF CONTENTS

CHAPTER 1 INTRODUCTION

1.1 USING THIS MANUAL................................................................... 1

1.2 GETTING HELP............................................................................. 2

1.3 BRIM-E6 OVERVIEW..................................................................... 2

1.4 BRIM-E6 FEATURES..................................................................... 2

1.5 BRIM-E6 SPECIFICATIONS.......................................................... 3

1.6 ETHERNET BRIDGING ................................................................. 4

1.7 RELATED MANUALS..................................................................... 6

CHAPTER 2 INSTALLATION

2.1 UNPACKING THE BRIM................................................................ 7

2.2 INSTALLING BRIMs....................................................................... 7

2.2.1 Installing a BRIM-E6 in a MIM........................................... 8

2.2.2 Installing a BRIM in a Hub............................................... 10

2.2.3 Installing an EPIM into the BRIM..................................... 11

CHAPTER 3 CONNECTING TO THE NETWORK

3.1 CONNECTING THE BRIM TO THE NETWORK.......................... 13

3.1.1 Connecting a UTP Segment to an EPIM-T...................... 13

3.1.2 Connecting a Fiber Optic Link Segment to

an EPIM-F1, EPIM-F2, or EPIM-F3................................. 15

3.1.3 Connecting a Thin-Net Segment to an EPIM-C............... 17

3.1.4 Connecting an AUI Cable to an EPIM-A.......................... 19

3.1.5 Connecting an AUI Cable to an EPIM-X.......................... 20

3.2 FINISHING THE INSTALLATION................................................. 21

CHAPTER 4 USING THE LANVIEW LEDS

4.1 STB (Standby).............................................................................. 23

4.2 XMT (Transmit)............................................................................. 23

4.3 CLN (Collision) ............................................................................. 23

4.4 RCV (Receive).............................................................................. 23

CONTENTS

BRIM-E6 USER’S GUIDE

APPENDIX A EPIM SPECIFICATIONS

A.1 EPIM-T (10BASE-T TWISTED PAIR PORT)................................25

A.2 EPIM-F1 AND EPIM-F2 (MULTIMODE FIBER OPTIC PORTS)..26

A.3 EPIM-F3 (SINGLE MODE FIBER OPTIC PORT).........................27

A.4 EPIM-C (BNC PORT) ...................................................................29

A.5 EPIM-A AND EPIM-X (AUI PORTS).............................................30

APPENDIX B EPIM CABLE REQUIREMENTS

B.1 CABLE REQUIREMENTS ............................................................31

B.1.1 10BASE-T UTP and STP Cable Requirements...............31

B.1.2 FOIRL/10BASE-FL Multimode Fiber Optic Cable

Requirements...................................................................33

B.1.3 FOIRL/10BASE-FL Single Mode Fiber Optic Cable

Requirements...................................................................34

B.1.4 10BASE-2 Thin-net Cable Requirements ........................35

B.1.5 AUI Cable Requirements .................................................36

INDEX

BRIM-E6 USER’S GUIDE

Page 1

CHAPTER 1

INTRODUCTION

Welcome to the Cabletron Systems

BRIM-E6 User’s Guide

. This

manual explains how to install the Bridge/Router Interface Module

(BRIM) for Ethernet into Cabletron products that support BRIM

technology (e.g., the EMM-E6 or MicroMMAC). It also explains

BRIM-E6 features and specifications.

1.1 USING THIS MANUAL

Read through this manual completely to familiarize yourself with its

content and to gain an understanding of the features and capabilities of

the BRIM-E6.A general working knowledge of Ethernet, and IEEE 802.3

type data communications networks and their physical layer components

is helpful when using the BRIM-E6.

Chapter 1,

Introduction

, describes BRIM-E6 features, lists

speciﬁcations, and concludes with a list of related manuals.

Chapter 2,

Installation

, describes how to install the BRIM-E6 into a

Media Interface Module (MIM) or a stand-alone product. This chapter

also explains how to install an Ethernet Port Interface Module (EPIM)

into the BRIM.

Chapter 3,

Connecting to the Network

, explains how to connect network

segments to the EPIM.

Chapter 4,

Using the LANVIEW LEDS

, describes how to use the

BRIM-E6 LEDs to monitor BRIM performance and status.

Appendix A,

EPIM Speciﬁcations

, lists speciﬁcations for each of the

EPIMs available for the BRIM-E6.

Appendix B,

EPIM Cable

Requirements

lists cable requirements for

each of the EPIMs.

CHAPTER 1:

INTRODUCTION

Page 2

BRIM-E6 USER’S GUIDE

1.2 GETTING HELP

If you need additional support related to the BRIM-E6, or if you have any

questions, comments, or suggestions concerning this manual, contact

Cabletron Systems Technical Support:

By phone ..........................(603) 332-9400

Monday-Friday; 8am - 8pm EST

By CompuServe

.............GO CTRON from any! prompt

By Internet mail ...............[email protected]

1.3 BRIM-E6 OVERVIEW

The BRIM-E6 extends the functionality of your individual MIM or

stand-alone hub to include Ethernet bridging capability. The BRIM-E6

has one user-conﬁgurable Ethernet Port Interface Module (EPIM)

interface. Cabletron Systems offers a variety of EPIMs that support

connections for Unshielded Twisted Pair, Shielded Twisted Pair,

Multimode Fiber Optic, Single Mode Fiber Optic, AUI, or Thin Coaxial

cable.

1.4 BRIM-E6 FEATURES

Ethernet Bridging

The BRIM-E6 adds an Ethernet bridged connection to any Cabletron

device with a BRIM expansion port. Refer to section 1.6 for more

information about Ethernet bridging.

MIB Support

For information on how to extract and compile individual MIBs, contact

Cabletron Systems Technical Support (see

Getting Help

LANVIEW Diagnostic LEDs

Cabletron equips the BRIM-E6 with a visual diagnostic and monitoring

system called LANVIEW. LANVIEW LEDs help you quickly identify

Bridge and Link status.

BRIM-E6 SPECIFICATIONS

BRIM-E6 USER’S GUIDE

Page 3

EPIM Connectivity

EPIMs allow you to conﬁgure the BRIM-E6 to support a variety of media

types. Cabletron Systems offers the EPIMs shown in Table 1-1.

1.5 BRIM-E6 SPECIFICATIONS

The operating speciﬁcations for the BRIM-E6 are described in this

section. Cabletron Systems reserves the right to change these

speciﬁcations at any time without notice.

Environmental Requirements

Operating Temperature: -5

to +40

Non-operating Temperature: -30

to +90

Operating Humidity: 5 to 95% (non-condensing)

Safety and Approvals

This unit meets the safety requirements of UL 1950, CSA C22.2 NO 950,

and EN 60950; the EMI requirements of FCC Class A and EN 55022

Class A; and the EMC requirements of EN 50082-1.

Table 1-1. EPIMs

EPIM MEDIA TYPE CONNECTOR

EPIM-A AUI DB15 (Female)

EPIM-C 10BASE-2 Thin Coaxial BNC

EPIM-T 10BASE-T Unshielded

Twisted Pair RJ45

EPIM-X Standard Transceiver DB15 (Male)

EPIM-F1 Multimode Fiber SMA

EPIM-F2 Multimode Fiber ST

EPIM-F3 Single Mode Fiber ST

Inhaltsverzeichnis

Andere Cabletron Systems Netzwerk-Router Handbücher

Cabletron Systems

Cabletron Systems Spectrum EMM-E6 Bedienungsanleitung

Cabletron Systems

Cabletron Systems MMAC-Plus 9T101-04 Bedienungsanleitung

Cabletron Systems

Cabletron Systems SMARTSWITCH ROUTER 9032578-05 Montageanleitung

Cabletron Systems

Cabletron Systems CyberSWITCH CSX500 Bedienungsanleitung

Cabletron Systems

Cabletron Systems 3H02-04 Bedienungsanleitung

Cabletron Systems

Cabletron Systems CSX100 series Bedienungsanleitung

Cabletron Systems

Cabletron Systems BRIM-WT1 Bedienungsanleitung

Cabletron Systems

Cabletron Systems CyberSWITCH CSX400 Bedienungsanleitung

Cabletron Systems

Cabletron Systems SmartSTACK ELS100-24TXG Bedienungsanleitung

Cabletron Systems

Cabletron Systems ESX-1380 Programmierhandbuch

Cabletron Systems

Cabletron Systems MMAC-Plus 9T106-01 Bedienungsanleitung

Cabletron Systems

Cabletron Systems MMAC-Plus 9F106-01 Bedienungsanleitung

Cabletron Systems

Cabletron Systems BRIM E100 BRIM-E100 Bedienungsanleitung

Cabletron Systems

Cabletron Systems 2000 Bedienungsanleitung

Cabletron Systems

Cabletron Systems SmartSwitch 8-slot Montageanleitung

Cabletron Systems

Cabletron Systems DELST-UI Programmierhandbuch

Cabletron Systems

Cabletron Systems MMAC-Plus 9W111-08 Bedienungsanleitung

Cabletron Systems

Cabletron Systems CyberSWITCH CSX101 Betriebsanleitung

Cabletron Systems

Cabletron Systems FDMMIM Bedienungsanleitung

Cabletron Systems

Cabletron Systems ESX-1380 Montage- und Bedienungsanleitung

Cabletron Systems

Cabletron Systems ELS100 Bedienungsanleitung

Cabletron Systems

Cabletron Systems SSR-600 Bedienungsanleitung

Cabletron Systems

Cabletron Systems SmartSwitch 2200 Bedienungsanleitung

Cabletron Systems

Cabletron Systems SmartSwitch Router Montageanleitung

Beliebte Netzwerk-Router Handbücher anderer Marken

Allnet

Allnet ALL0333AU Bedienungsanleitung

HomeSeer

HomeSeer HT-SEL Bedienungsanleitung

Sercomm

Sercomm Genesis OC3505D Bedienungsanleitung

Billion

Billion BIPAC 5102 Series Bedienungsanleitung

TP-Link

TP-Link TD-8817 Bedienungsanleitung

Motorola

Motorola MR1900 Bedienungsanleitung

Digi

Digi IX14 Bedienungsanleitung

Cisco

Cisco NCS 540 Handbuch

XAVi

XAVi X8821e Bedienungsanleitung

BEC

BEC 6200WZL Bedienungsanleitung

MikroTik

MikroTik hAP ac3 Series Bedienungsanleitung

Korenix

Korenix JetNet 5428G Series Bedienungsanleitung

NETGEAR

NETGEAR FS526T - Switch Bedienungsanleitung

Korenix

Korenix JetNet 5710G Series Bedienungsanleitung

Automated Logic

Automated Logic ZN551 Betriebsanleitung

Cisco

Cisco ASR 1000 Series Bedienerhandbuch

EnGenius

EnGenius ESR-9710 Bedienungsanleitung

Cisco

Cisco 805 Series Bedienungs- und Sicherheitshinweise