Cabletron Systems SSR 2000 Bedienungsanleitung

Installing an Expansion Module on the SSR 2000 1

39-078-01

Installing an Expansion Module in the SSR 2000

Warning:Before performing any upgrade or installation procedures, ensure that the

SSR 2000 is powered off and that you are properly grounded to avoid electrostatic

discharge while working inside the SSR 2000’s chassis.

It may be necessary at some point for you to upgrade or replace your SSR 2000’s

expansion module(s) after receiving your SSR 2000 from Cabletron. You can install any of

the available expansion modules in either of the SSR 2000’s expansion slots.

Note: You can also reference material on installing an expansion module in the

SmartSwitch Router 2000 Getting Started Guide.

To install an expansion module:

1. Ensure that the SSR 2000 is powered off.

2. If your SSR 2000 is equipped for rackmountability, use the phillips-head screwdriver

to remove the mounting brackets from each side of the SSR 2000.

3. Take off the SSR 2000’s top cover.

a. Use the phillips-head screwdriver to remove the four mounting screws (two on

each side of the router, front and back) that hold the top cover on the SSR 2000.

Figure 1. Removing the SSR 2000’s cover

b. Slide the cover away from the front of the SSR 2000 about 1/2”, then lift it away

from the SSR 2000.

4. Use the phillips-head screwdriver to remove the four mounting screws in the existing

face plate or cover plate corresponding to the expansion slot where you plan to install

the expansion module. Be sure not to damage or remove the conductive tape on the

inside of the chassis, both above and below the expansion slot opening. (See Figure 2,

below.)

87654321 87654321

2000

CONSOLE

10/100 MGMT

ERR DIAG

HBT

RST

10/100BASE-TX 10/100BASE-TX

SSR-2

SYS

39-078-01

2 Installing an Expansion Module on the SSR 2000

Figure 2. Removing a face plate or cover plate (view from outside chassis)

5. From the inside of the chassis, line up the four holes in the expansion module’s face

plate with the corresponding holes around the empty expansion slot in the chassis,

and use the phillips-head screwdriver to tighten the screws (from the front) on each

side of the expansion module’s face plate to affix it to the chassis. (See Figure 3,

below.)

Note: You will probably have to gently push the expansion module’s face plate

down while lining up the first of the screws. The grounding fingers for the

10/100BASE-TX module that sits immediately below the empty expansion

slot protrude upwards to make contact with the bottom of the face plate.

Figure 3. Installing the new face plate (view from inside chassis)

6. This step applies only if you are installing a 100 Base-FX module (part number SSR-2-

FX). In order for the 100 Base-FX module to be aligned properly in the SSR 2000’s

chassis, 5-millimeter extensions must be attached to the six standoffs holding the

module in place on the SSR 2000’s motherboard.

blank expansion module face plate

Installing an Expansion Module on the SSR 2000 3

39-078-01

Figure 4 illustrates how the extensions are attached onto the standoffs on the SSR

2000’s motherboard.

Figure 4. Attaching 5-mm extensions to the standoffs on the SSR 2000 motherboard

(necessary only when installing an SSR-2-FX module)

7. Insert the expansion module from the top and ensure that it makes maximum surface

contact with its face plate.

8. Line up the two screw holes at the back of the expansion module and connect the

female stacking connector at the back of the expansion module to the male stacking

connector on the SSR 2000’s motherboard.

Warning:The female and male stacking connectors for the expansion modules are not

keyed, so it is possible to misalign the connection. Ensure that all pins fit properly into the

female stacking connector on the expansion module before applying power to the SSR

2000.

9. Use the phillips-head screwdriver to tighten all six screws that will hold the

expansion module in place in the SSR 2000’s chassis.

87654321 87654321

2000

87654321

10/100BASE-TX

CONSOLE

10/100 MGMT

ERR DIAG

HBT

SSR-2-TX

10/100BASE-TX 10/100BASE-TX

RST

SYS

SSR-2

SSR-2-FX 100BASE-FX

Lnk Act Lnk Act Lnk Act Lnk Act Lnk Act Lnk Act Lnk Act Lnk Act

2345678

39-078-01

4 Installing an Expansion Module on the SSR 2000

Figure 5. Installing an expansion module

10. Replace the SSR 2000’s cover.

When you are ready to attach the segment cables, use the procedures in “Attaching Port

Cables” in the SmartSwitch Router 2000 Getting Started Guide.

87654321 87654321

2000

1000BASE-SX

87654321

10/100BASE-TX

CONSOLE

10/100 MGMT

ERR DIAG

HBT

SSR-2-TX SSR-2-SX

10/100BASE-TX 10/100BASE-TX

Rx AN

LinkTx

Rx AN

Link

RST

SYS

SSR-2

Inhaltsverzeichnis

Andere Cabletron Systems Netzwerk-Router Handbücher

Cabletron Systems

Cabletron Systems SmartSwitch Router Montageanleitung

Cabletron Systems

Cabletron Systems CyberSWITCH CSX400 Bedienungsanleitung

Cabletron Systems

Cabletron Systems SmartSTACK ELS100-24TXG Bedienungsanleitung

Cabletron Systems

Cabletron Systems ELS100 Bedienungsanleitung

Cabletron Systems

Cabletron Systems 2H253-25R Bedienungsanleitung

Cabletron Systems

Cabletron Systems SSR 2000 Bedienungsanleitung

Cabletron Systems

Cabletron Systems CyberSWITCH CSX400 Bedienungsanleitung

Cabletron Systems

Cabletron Systems ESX-1380 Montage- und Bedienungsanleitung

Cabletron Systems

Cabletron Systems Spectrum EMM-E6 Bedienungsanleitung

Cabletron Systems

Cabletron Systems SmartSwitch 8-slot Montageanleitung

Cabletron Systems

Cabletron Systems SSR-600 Bedienungsanleitung

Cabletron Systems

Cabletron Systems BRIM E100 BRIM-E100 Bedienungsanleitung

Cabletron Systems

Cabletron Systems CyberSWITCH CSX101 Betriebsanleitung

Cabletron Systems

Cabletron Systems SmartSwitch Router 520 Bedienerhandbuch

Cabletron Systems

Cabletron Systems CSX200 CyberSWITCH Bedienungsanleitung

Cabletron Systems

Cabletron Systems BRIM-E6 Bedienungsanleitung

Cabletron Systems

Cabletron Systems SmartSwitch 9000 Bedienungsanleitung

Cabletron Systems

Cabletron Systems CyberSWITCH CSX400 Bedienungsanleitung

Cabletron Systems

Cabletron Systems MMAC-Plus 9T106-01 Bedienungsanleitung

Cabletron Systems

Cabletron Systems SmartSwitch Router Montageanleitung

Cabletron Systems

Cabletron Systems MMAC-Plus 9W111-08 Bedienungsanleitung

Cabletron Systems

Cabletron Systems MMAC-Plus 9F106-02 Bedienungsanleitung

Cabletron Systems

Cabletron Systems Network Router Bedienungsanleitung

Cabletron Systems

Cabletron Systems SmartSwitch 2200 Bedienungsanleitung

Beliebte Netzwerk-Router Handbücher anderer Marken

Allnet

Allnet ALL0333AU Bedienungsanleitung

HomeSeer

HomeSeer HT-SEL Bedienungsanleitung

Sercomm

Sercomm Genesis OC3505D Bedienungsanleitung

Billion

Billion BIPAC 5102 Series Bedienungsanleitung

TP-Link

TP-Link TD-8817 Bedienungsanleitung

Motorola

Motorola MR1900 Bedienungsanleitung

Digi

Digi IX14 Bedienungsanleitung

Cisco

Cisco NCS 540 Handbuch

XAVi

XAVi X8821e Bedienungsanleitung

BEC

BEC 6200WZL Bedienungsanleitung

MikroTik

MikroTik hAP ac3 Series Bedienungsanleitung

Korenix

Korenix JetNet 5428G Series Bedienungsanleitung

NETGEAR

NETGEAR FS526T - Switch Bedienungsanleitung

Korenix

Korenix JetNet 5710G Series Bedienungsanleitung

Automated Logic

Automated Logic ZN551 Betriebsanleitung

Cisco

Cisco ASR 1000 Series Bedienerhandbuch

EnGenius

EnGenius ESR-9710 Bedienungsanleitung

Cisco

Cisco 805 Series Bedienungs- und Sicherheitshinweise