Cabletron Systems Cabletron CyberSWITCH CSX5500 Bedienungsanleitung

CENTRAL SITE

REMOTE ACCESS SWITCH

QUICK START

Release 7.4

Cabletron Systems

(603) 332-9400 phone

(603) 337-3075 fax

support@ctron.com

QUICK START

2 CyberSWITCH

NOTICE

You may post this document on a network server for public use as long as no

modifications are made to the document.

Cabletron Systems reserves the right to make changes in specifications and other

information contained in this document without prior notice. The reader should in

all cases consult Cabletron Systems to determine whether any such changes have

been made.

The hardware, firmware, or software described in this manual is subject to change

without notice.

IN NO EVENT SHALL CABLETRON SYSTEMS BE LIABLE FOR ANY

INCIDENTAL, INDIRECT, SPECIAL, OR CONSEQUENTIAL DAMAGES

WHATSOEVER (INCLUDING BUT NOT LIMITED TO LOST PROFITS) ARISING

OUT OF OR RELATED TO THIS MANUAL OR THE INFORMATION

CONTAINED IN IT, EVEN IF CABLETRON SYSTEMS HAS BEEN ADVISED OF,

KNOWN, OR SHOULD HAVE KNOWN, THE POSSIBILITY OF SUCH

DAMAGES.

Cabletron Systems, Inc.

P.O. Box 5005

Rochester, NH 03866-5005

Order Number: 9032109-04

VIRUS DISCLAIMER

Cabletron Systems has tested its software with current virus checking

technologies. However, because no anti-virus system is 100% reliable, we strongly

caution you to write protect and then verify that the Licensed Software, prior to

installing it, is virus-free with an anti-virus system in which you have confidence.

Cabletron Systems makes no representations or warranties to the effect that the

Licensed Software is virus-free.

Only qualified personnel should perform installation

procedures.

CAUTION

Central Site Remote Access Switch 3

TRADEMARKS

Cabletron Systems, CyberSWITCH, MMAC-Plus, SmartSWITCH, SPECTRUM,

and SecureFast Virtual Remote Access Manager are trademarks of Cabletron

Systems, Inc.

All other product names mentioned in this manual are trademarks or registered

trademarks of their respective companies.

COPYRIGHTS

All of the code for this product is copyrighted by Cabletron Systems, Inc.

United States of America.

Portionsofthecodeforthisproductarecopyrighted bythefollowingcorporations:

Epilogue Technology Corporation

Livingston Enterprises, Inc.

Security Dynamics Technologies Inc.

Stac Electronics

Stac Electronics 1993, including one or more U.S. Patents No. 4701745, 5016009,

5126739 and 5146221 and other pending patents.

Telenetworks

FCC NOTICE

This device complies with Part 15 of the FCC rules. Operation is subject to the

following two conditions: (1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that

may cause undesired operation.

NOTE: This equipment has been tested and found to comply with the limits for a

Class A digital device, pursuant to Part 15 of the FCC rules. These limits are

designed to provide reasonable protection against harmful interference when the

equipment is operated in a commercial environment. This equipment uses,

generates, and can radiate radio frequency energy and if not installed in

accordance with the operator’s manual, may cause harmful interference to radio

communications. Operation of this equipment in a residential area is likely to cause

interference in which case the user will be required to correct the interference at his

own expense.

QUICK START

4 CyberSWITCH

WARNING: Changes or modifications made to this device which are not expressly

approved by the party responsible for compliance could void the user’s authority

to operate the equipment.

DOC NOTICE

This digital apparatus does not exceed the Class A limits for radio noise emissions

from digital apparatus set out in the Radio Interference Regulations of the

Canadian Department of Communications.

Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les

limites applicables aux appareils numériques de la class A prescrites dans le

Règlement sur le brouillage radioélectrique édicté par le ministère des

Communications du Canada.

VCCI NOTICE

This is a Class 1 product based on the standard of the Voluntary Control Council

for Interference by Information Technology Equipment (VCCI). If this equipment

is used in a domestic environment, radio disturbance may arise. When such

trouble occurs, the user may be required to take corrective actions.

CABLETRON SYSTEMS, INC. PROGRAM LICENSE AGREEMENT

IMPORTANT: Before utilizing this product, carefully read this License Agreement.

This document is an agreement between you, the end user, and Cabletron Systems,

Inc. ("Cabletron") that sets forth your rights and obligations with respect to the

Cabletron software program (the "Program") contained in this package. The

Program may becontained infirmware, chips or other media.BY UTILIZING THE

ENCLOSED PRODUCT, YOU ARE AGREEING TO BECOME BOUND BY THE

TERMS OF THIS AGREEMENT, WHICH INCLUDES THE LICENSE AND THE

LIMITATION OF WARRANTY AND DISCLAIMER OF LIABILITY. IF YOU DO

NOT AGREE TO THE TERMS OF THIS AGREEMENT, PROMPTLY RETURN

THE UNUSED PRODUCT TO THE PLACE OF PURCHASE FOR A FULL

REFUND.

Central Site Remote Access Switch 5

CONTENTS

Using Quick Start 7

Basics 8

Installing Hardware 8

Installing Software 8

Accessing the Release Notes 8

Accessing the CyberSWITCH 9

Connecting an Administration Console 9

Connecting a Local Administration Console 9

Connecting a Remote Administration Console 9

Making Configuration Changes 10

Upgrading System Software 11

Local Software Upgrade Instructions 11

Remote Upgrade 12

Handling Upgrade Warnings and Errors 13

Change Defaults to Secure System 13

Initial Installation Steps 14

Beginning the Configuration Process 14

Physical Resource Configuration 15

Connectivity 16

Overview 16

Connecting a Central Site Product to a Workgroup Product via PPP 16

Bridge to Bridge Configuration 16

Configuration for Site "Remote" 17

IP Router to IP Router Configuration 18

Configuration for Site "Central" 18

Configuration for Site "Remote" 19

IPX Router to IPX Router Configuration 20

Configuration for Site "Central" 20

Configuration for Site "Remote" 21

AppleTalk Router to AppleTalk Router Configuration 22

Configuration for Site "Central" 22

Configuration for Site "Remote" 23

Connecting a Central Site Product to a CSX100 via PPP 24

IP Router to IP Router with Network Address Translation Configuration 24

Configuration for Site “Central” 25

Configuration for Site “Remote” 25

IPX Router to IPX Router Configuration 26

Configuration for Site “Central” 26

Configuration for Site “Remote” 27

IPX Router to Bridge Configuration 28

Configuration for Site “Central” 28

Configuration for Site “Remote” 29

AppleTalk Router to Bridge Configuration 29

Configuration for Site “Central” 29

Configuration for Site “Remote” 30

QUICK START

6 CyberSWITCH

Connecting a Central Site Product to a Terminal Adapter/Modem 31

IP Router with Digital Modem to a Terminal Adapter/Modem 31

Configuration for Site “Central” 31

Configuration for Site "Remote" on Windows NT 4.0 31

Configuration of Site “Remote” on Windows 95 34

IPX Router with Digital Modem to a Terminal Adapter/Modem 36

Configuration for Site “Central” 36

Configuration for Site “Remote” on Windows NT 4.0 36

Configuration of Site “Remote” on Windows 95 39

Index 41

SING

UICK

TART

Quick Start is recommended only for those users who are experienced with hardware and software

installation procedures. Quick Start is divided into two parts.

•Basics

This chapter gives detailed instructions on the initial installation steps that are required for all

CyberSWITCH configurations.

• Connectivity

This chapter gives instructions for connecting two of our products together via PPP. Separate

instructions are provided for bridging, IP, IPX, and AppleTalk configurations.

ASICS

INSTALLING HARDWARE

There is a possibility that your distributor has already completed hardware installation. If

hardware installation has not been completed, follow the instructions listed below.

WARNING:

Anytime you remove the module cover, make sure the power cord is not plugged in.

Failure to do so may result in personal injury or equipment damage.

1. Remove module cover.

2. Install adapters.

3. Attach LCD Cable to WAN adapter.

4. Install needed inter-board cables (for TDM and/or MVIP connections).

5. Replace module cover.

INSTALLING SOFTWARE

1. Insert system software diskette #1 into diskette drive and power on the machine.

2. Type the following command at the DOS prompt:

install

3. If you wish to review the Release Notes answer “y” to the prompt. Use <page down> and

<page up> to view sections of the Release Notes. At anytime you may press the <Esc> key to

continue with the installation.

4. Follow the on-screen instructions to complete the software installation.

ACCESSING THE RELEASE NOTES

The Release Notes provide release highlights and important information related to this release that

should be reviewed before you begin the system’s installation and configuration.

An abbreviated set of these notes are in a file called REL_NOTE.TXT. To display them on the

system, enter the following command at the system prompt:

[product name]> LIST REL_NOTE.TXT

Or, you may access the complete set of notes via your Web browser:

http://www.cabletron.com/support/relnotes

Central Site Remote Access Switch 9

ASICS

Accessing the CyberSWITCH

ACCESSING THE CYBERSWITCH

CONNECTING AN ADMINISTRATION CONSOLE

This section describes how to connect an administration console. Youwill use the console to control

the system.

The system supports two administration console options: local and remote. Both options will be

explained in this section. Follow the steps for the administration console option you will be using.

Note: Once the system is up and running, you may wish to connect to the console using Telnet.

Refer to the Remote Management chapter of the User’s Guide for additional information

concerning Telnet.

CONNECTING ALOCAL ADMINISTRATION CONSOLE

With a local administration console, the user creates a direct connection to the CyberSWITCH by

attaching a monitor and keyboard to the system. It is configured to support a PS/2-style keyboard

and a VGA 15-pin monitor. These are NOT supplied. This simple connection process is explained

below:

1. Attach keyboard plug to the keyboard connector located on the back of the system.

2. Attach monitor cable to the local monitor port located on the back of the system.

For the exact location of the keyboard connector and the local monitor port, refer to the platform

diagrams included in the Hardware Overview chapter of the User’s Guide.

CONNECTING AREMOTE ADMINISTRATION CONSOLE

A remote administration console gives the user the ability to operate the CyberSWITCH remotely.

To use the remote administration console option, you will need an IBM Compatible PC that runs

Carbon Copy, and the appropriate cabling. These cables are NOT supplied. Refer to the Remote

Management chapter of the User’s Guide for additional information concerning Carbon Copy.

You will also need the Manager diskette toconnect the remote administration console option. This

software is available (as an option) when you order a CyberSWITCH. If you did not order the

Manager software, you must use the local administration console option. Call your distributor to

order this software.

To connect the Remote Administration Console, follow these steps:

1. Using the appropriate cabling, attach the administration console PC to the system.

The remote administration port is a 9-pin, male RS232 serial adapter. For the location of the

port, refer to the Hardware Overview chapter of the User’s Guide.

You can use a standard RS232 cable with a null-modem device for direct attachment between

the administration console PC and the CyberSWITCH. If you are using remote attachment,

connect the administration console PC and the system to their respective modems.

QUICK START

10 CyberSWITCH

2. Install the Manager software onto the administration console PC. This step is OPTIONAL,

since it requires the administration console PC to have a hard disk with 1 MB of free space. You

can execute the Manager software from the diskette; however, running this software from the

hard disk is more efficient.

Insert the Manager software diskette into the diskette drive on the administration console PC

and enter the following command, replacing “diskette drive letter” with the appropriate

administration console PC drive (for example “A”). Type:

install<return>

When the DOS prompt reappears, the software installation on the administration console is

complete.

The Carbon Copy software on the Manager diskette is delivered with the following default

settings:

Comm Port Address COM1

Baud Rate 9600

Modem Type Direct Connect

If you want to attach remotely to the system using modems, you must change these settings by

using the CCINSTAL program. Refer to the Remote Management chapter of the User’s Guide for

details on running this program.

Once you have a connection to the CyberSWITCH, you will be presented with a prompt to enter

your log in id. Use admin as the login id. You will then be prompted for a new password, so choose

a password that you will remember. If your software was previously accessed by your distributor,

your password will be admin (in lower case).

After you have logged in, you many enter any command at the system prompt.

MAKING CONFIGURATION CHANGES

We provide the following configuration tools to set up and/or alter your configuration:

• CFGEDIT, the full configuration utility

• Manage Mode, the dynamic management utility

The CyberSWITCH is configured using the configuration editor, CFGEDIT. To begin the

configuration process:

Start up the configuration editor, CFGEDIT. Your machine should beat the systemprompt. To start

up the configuration editor simply type:

[system name]>

cfgedit

The main configuration menu should now be displayed. Refer to Connectivity for the configuration

steps required for the device you wish to connect.

Andere Handbücher für Cabletron CyberSWITCH CSX5500

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Cabletron Systems Schalten Handbücher

Cabletron Systems

Cabletron Systems 9F120-08 Technisches Dokument

Cabletron Systems

Cabletron Systems 9G421-02 Technisches Dokument

Cabletron Systems

Cabletron Systems SMALL OFFICE CyberSwitch 150 Bedienungsanleitung

Cabletron Systems

Cabletron Systems TRMIM 24A TRMIM-24A Bedienungsanleitung

Cabletron Systems

Cabletron Systems SmartSTACK ELS100-S24TX2M Programmierhandbuch

Cabletron Systems

Cabletron Systems MMAC-Plus 9T125-24 Bedienungsanleitung

Cabletron Systems

Cabletron Systems MMAC-Plus 9T125-24 Handbuch

Cabletron Systems

Cabletron Systems MMAC-Plus 9A000 Bedienungsanleitung

Cabletron Systems

Cabletron Systems SmartSwitch 6500 Bedienungsanleitung

Cabletron Systems

Cabletron Systems MMAC-Plus 9H531-24 Bedienungsanleitung

Cabletron Systems

Cabletron Systems SEHI100TX-22 Bedienungsanleitung

Cabletron Systems

Cabletron Systems Ethernet Hubs Bedienungsanleitung

Cabletron Systems

Cabletron Systems CSX200 CyberSWITCH Bedienungsanleitung

Cabletron Systems

Cabletron Systems MicroMMAC-24E Bedienungsanleitung

Cabletron Systems

Cabletron Systems SmartCell 6A000 Bedienungsanleitung

Cabletron Systems

Cabletron Systems MMAC-Plus 9H421-12 Handbuch

Cabletron Systems

Cabletron Systems TRFMIM 28 TRFMIM-28 Bedienungsanleitung

Cabletron Systems

Cabletron Systems SmartSTACK ELS100-24TXG Bedienungsanleitung

Cabletron Systems

Cabletron Systems SmartSTACK 10 ELS10-26 Bedienungsanleitung

Cabletron Systems

Cabletron Systems SmartSTACK ELS100-8TXUF2 Bedienungsanleitung

Cabletron Systems

Cabletron Systems ATX Bedienungsanleitung

Cabletron Systems

Cabletron Systems FRM Bedienungsanleitung

Cabletron Systems

Cabletron Systems MMAC-Plus 9EX02-12 Bedienungsanleitung

Cabletron Systems

Cabletron Systems MMAC-Plus 9E312-12 Technisches Dokument

Beliebte Schalten Handbücher anderer Marken

URC

URC Total Control MFS-8 Bedienungsanleitung

Azbil

Azbil HPQ-D11 Bedienungsanleitung

Sony

Sony DFS-900M Bedienungsanleitung

SICK

SICK i17S Bedienungsanleitung

F&F

F&F SZR-277 Bedienungsanleitung

Shure

Shure UAMS/BK Bedienungsanleitung

Dräger

Dräger X-zone Switch Off Bedienungsanleitung

Asco

Asco Joucomatic 349 Series Bedienungsanleitung

BT Mini Hub Bedienungsanleitung

D-Link

D-Link DES-1226G Bedienungsanleitung

Johnson Controls

Johnson Controls FS80-C Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Bedienungsanleitung

MicroNet

MicroNet SP1200A Bedienungsanleitung

Ruijie

Ruijie RG-PF2920 Series Installations- und Betriebsanleitung

Altinex

Altinex DA1914SX Bedienungsanleitung

MiLAN

MiLAN MIL-SM2401M Bedienungsanleitung

RJM

RJM MASTERMIND PBC/6X Bedienungsanleitung

Atlas

Atlas MMK-KVM8 Bedienungsanleitung