Cabletron Systems Cyber SWITCH 1000 Bedienungsanleitung

WORKGROUP

REMOTE ACCESS SWITCH

EXAMPLE NETWORKS

Release 7.2

Cabletron Systems

(603) 332-9400 phone

(603) 337-3075 fax

support@ctron.com

EXAMPLE NETWORKS

2 CyberSWITCH

NOTICE

You may post this document on a network server for public use as long as no

modifications are made to the document.

Cabletron Systems reserves the right to make changes in specifications and other

information contained in this document without prior notice. The reader should in

all cases consult Cabletron Systems to determine whether any such changes have

been made.

The hardware, firmware, or software described in this manual is subject to change

without notice.

IN NO EVENT SHALL CABLETRON SYSTEMS BE LIABLE FOR ANY

INCIDENTAL, INDIRECT, SPECIAL, OR CONSEQUENTIAL DAMAGES

WHATSOEVER (INCLUDING BUT NOT LIMITED TO LOST PROFITS) ARISING

OUT OF OR RELATED TO THIS MANUAL OR THE INFORMATION

CONTAINED IN IT, EVEN IF CABLETRON SYSTEMS HAS BEEN ADVISED OF,

KNOWN, OR SHOULD HAVE KNOWN, THE POSSIBILITY OF SUCH

DAMAGES.

Cabletron Systems, Inc.

P.O. Box 5005

Rochester, NH 03866-5005

Order Number:9032236-02

VIRUS DISCLAIMER

Cabletron Systems has tested its software with current virus checking

technologies. However, because no anti-virus system is 100% reliable, we strongly

caution you to write protect and then verify that the Licensed Software, prior to

installing it, is virus-free with an anti-virus system in which you have confidence.

Cabletron Systems makes no representations or warranties to the effect that the

Licensed Software is virus-free.

Only qualified personnel should perform installation

procedures.

CAUTION

Workgroup Remote Access Switch 3

TRADEMARKS

Cabletron Systems, CyberSWITCH, MMAC-Plus, SmartSWITCH, SPECTRUM,

and SecureFast Virtual Remote Access Manager are trademarks of Cabletron

Systems, Inc.

All other product names mentioned in this manual are trademarks or registered

trademarks of their respective companies.

COPYRIGHTS

All of the code for this product is copyrighted by Cabletron Systems, Inc.

United States of America.

Portionsofthecodeforthisproductarecopyrightedbythefollowingcorporations:

Epilogue Technology Corporation

Livingston Enterprises, Inc.

Security Dynamics Technologies Inc.

Stac Electronics

Stac Electronics 1993, including one or more U.S. Patents No. 4701745, 5016009,

5126739 and 5146221 and other pending patents.

Telenetworks

FCC NOTICE

This device complies with Part 15 of the FCC rules. Operation is subject to the

following two conditions: (1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that

may cause undesired operation.

NOTE: This equipment has been tested and found to comply with the limits for a

Class A digital device, pursuant to Part 15 of the FCC rules. These limits are

designed to provide reasonable protection against harmful interference when the

equipment is operated in a commercial environment. This equipment uses,

generates, and can radiate radio frequency energy and if not installed in

accordance with the operator’s manual, may cause harmful interference to radio

communications. Operation of this equipment in a residential area is likely to cause

interference in which case the user will be required to correct the interference at his

own expense.

EXAMPLE NETWORKS

4 CyberSWITCH

WARNING: Changes or modificationsmade to this device which are not expressly

approved by the party responsible for compliance could void the user’s authority

to operate the equipment.

DOC NOTICE

This digital apparatus does not exceed the Class A limits for radio noise emissions

from digital apparatus set out in the Radio Interference Regulations of the

Canadian Department of Communications.

Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les

limites applicables aux appareils numériques de la class A prescrites dans le

Règlement sur le brouillage radioélectrique édicté par le ministère des

Communications du Canada.

VCCI NOTICE

This is a Class 1 product based on the standard of the Voluntary Control Council

for Interference by Information Technology Equipment (VCCI). If this equipment

is used in a domestic environment, radio disturbance may arise. When such

trouble occurs, the user may be required to take corrective actions.

CABLETRON SYSTEMS, INC. PROGRAM LICENSE AGREEMENT

IMPORTANT: Before utilizing this product, carefully read this License Agreement.

This document is an agreement between you, the end user, and Cabletron Systems,

Inc. ("Cabletron") that sets forth your rights and obligations with respect to the

Cabletron software program (the "Program") contained in this package. The

Program may be contained in firmware, chips or other media. BY UTILIZING THE

ENCLOSED PRODUCT, YOU ARE AGREEING TO BECOME BOUND BY THE

TERMS OF THIS AGREEMENT, WHICH INCLUDES THE LICENSE AND THE

LIMITATION OF WARRANTY AND DISCLAIMER OF LIABILITY. IF YOU DO

NOT AGREE TO THE TERMS OF THIS AGREEMENT, PROMPTLY RETURN

THE UNUSED PRODUCT TO THE PLACE OF PURCHASE FOR A FULL

REFUND.

Workgroup Remote Access Switch 5

CONTENTS

Simple Remote Bridging Network 9

Overview 9

Initial Installation Steps 9

Configuring the Simple Remote Bridge 9

Resources 10

Lines 10

Bridging and Routing Information 11

Bridging 11

IP Routing 11

Configure the CyberSWITCH 12

Save Configuration Files 15

Verify the Installation 16

Remote Bridging Network with Security 17

Overview 17

Initial Installation Steps 17

Resources 19

Lines 19

Device Information 20

Bridging and Routing Information 22

Bridging 22

IP Routing 22

Configure the CyberSWITCH 23

Configuring the Options 23

Configuring the Security 23

Save Configuration Files 26

Verify the Installation 27

IP Routing Network 28

Overview 28

Initial Installation Steps 28

System Details 30

Resources 30

Lines 30

Device Information 31

Device Information 33

Bridging and Routing Information 35

Bridging 35

IP Routing 35

Configure the CyberSWITCH 36

Configuring the CyberSWITCH Options 36

Configuring the Security 40

Save Configuration Files 43

Verify the Installation 44

IP Routing Network with Remote Bridge Devices 45

Overview 45

Business Assumptions 45

Initial Installation Steps 45

Resources 47

EXAMPLE NETWORKS

6 CyberSWITCH

Lines 47

Device Information 48

Bridging and Routing Information 50

Bridging 50

IP Routing 50

Configure the CyberSWITCH 51

Configuring the CyberSWITCH Options 51

Configuring the Security 54

Verify the Installation 57

IP Routing Network with PPP Devices 58

Overview 58

Initial Installation Steps 58

System Details 60

Resources 60

Lines 60

Bridging and Routing Information 61

Bridging 61

IP Routing 61

Bridging and Routing Information 62

Bridging 62

IP Routing 62

Device Information 63

Configure SITE1 65

Configuring the System Options 65

Finishing the Security Configuration 73

Configure SITE2 74

Configuring SITE2 Options 74

Configuring Security 75

Save Configuration Files 75

Verify the Installation 75

IPX Routing Network 77

Overview 77

Business Assumptions 77

Initial Installation Steps 77

System Details 79

Resources 79

Lines 79

Device Information 80

Bridging and Routing Information 83

Bridging 83

IP Routing 83

IPX Routing 84

Configure IPX Routing: Masternet (Detroit) 85

Configure Devices 85

Configure System Options 87

Save Configuration Files 92

Configure the Remote Devices 92

Verify the Installation 92

Workgroup Remote Access Switch 7

AppleTalk Routing Network 93

Overview 93

Initial Installation Steps 93

Resources 95

Lines 95

AppleTalk Routing 96

Configure the CyberSWITCH 98

Configuring the Options 98

Configuring Device Information 101

Configuring an AppleTalk Static Route 104

Save Configuration Files 105

Verify the Installation 105

Index 106

XAMPLE

ETWORKS

We provide several example networks, beginning with a simple network and progressing to more

complex networks. You may find the configuration instructions provided for each example helpful

when configuring your own network.

We include the following chapters:

• Simple Remote Bridging Network

An example ofa simple network using remote bridge devices to access a CyberSWITCH’s four

basic rate lines.

• Remote Bridging Network with Security

A bridged network with Calling Line Id security and Bridge MAC Address security enabled.

The network is configured with two devices. One device will be configured to require a Bridge

MAC Address security password, and one device will not. This network uses BRI lines.

•IPRoutingNetwork

An IP routing network with devices accessing the network from their homes.

• IP Routing Network with Remote Bridge Devices

A smart bridging interface to allow the two remote bridge devices to connect to an IP subnet.

The CyberSWITCH treats these devices connected to the Smart Bridging network interface as

if they were connected to the same Ethernet segment.

• IP Routing Network with PPP Devices

Uses IP routing to connect two of our products, both using PPP. Each system is on a separate

LAN. The configuration for this network is designed to allow three different types of accesses.

•IPXRoutingNetwork

A sample network using IPX protocol to communicatewith remote bridges as well as a remote

IPX router.

• AppleTalk Network

An AppleTalk network made up of two LANs, separated by the WAN.

IMPLE

EMOTE

RIDGING

ETWORK

OVERVIEW

This chapter provides an example of a simple network using remote bridge devices to access four

basic rate lines in the CyberSWITCH. Bridges are formed between each of the LANs to which the

remote bridge devices are connected, and the LAN to which the CyberSWITCH is connected.

The following section provides the initial installation steps that would be used with any type of

network installation.

INITIAL INSTALLATION STEPS

The initial steps in the CyberSWITCH installation process are basically the same no matter how

complicated the network. These steps are:

• completing the requirement worksheets

•orderingISDNservice

• powering on the system

• accessing Release Notes

• connecting an administration console

• setting up Telnet access

• upgrading system software

• changing defaults to secure system

• returning configuration to factory defaults

The chapters Accessing the CyberSWITCH and Upgrading System Software (in the User’s Guide)

describe each of these steps in detail.

Worksheets for this network are included on the next few pages.

CONFIGURING THE SIMPLE REMOTE BRIDGE

Because this is a simple bridged network, you only need to fill out the System Details and Bridging

and Routing Information worksheets. The worksheets for Example 1 are on the following pages.

EXAMPLE NETWORKS

10 CyberSWITCH

System Name:

SITE1

PAP Password:_______________ CHAP Secret:___________________

RESOURCES

LINES

BRI Lines

PRI Lines

V.35 and RS232 Lines

Type Slot Switch type Synchronization type

BRI 15ESS

Ethernet_1 2

Name Slot Port Line type Call screen TEI SPID Directory number

Line1 1 1 PPP Auto

Line2 1 2 PPP Auto

Line3 1 3 PPP Auto

Line4 1 4 PPP Auto

Name Slot Port Framing type Line coding Sig. method Line build-out

Name Slot Port Device/Network Idle character

SYSTEM DETAILS

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Cabletron Systems Schalten Handbücher

Cabletron Systems

Cabletron Systems TRFMIM 28 TRFMIM-28 Bedienungsanleitung

Cabletron Systems

Cabletron Systems DLEHF-MA Bedienungsanleitung

Cabletron Systems

Cabletron Systems FN10 Bedienungsanleitung

Cabletron Systems

Cabletron Systems 7C03 MMAC SmartSWITCH Bedienungsanleitung

Cabletron Systems

Cabletron Systems 3E02-04 Bedienungsanleitung

Cabletron Systems

Cabletron Systems FN10 Bedienungsanleitung

Cabletron Systems

Cabletron Systems CyberSWITCH CSX150 Bedienungsanleitung

Cabletron Systems

Cabletron Systems SmartSTACK ELS10-27TX Betriebsanleitung

Cabletron Systems

Cabletron Systems 2H28-08R Bedienungsanleitung

Cabletron Systems

Cabletron Systems IA1100 Montageanleitung

Cabletron Systems

Cabletron Systems MMAC-Plus 9H423-28 Handbuch

Cabletron Systems

Cabletron Systems 9E423-36 Bedienungsanleitung

Cabletron Systems

Cabletron Systems SmartSwitch 6E122 Betriebsanleitung

Cabletron Systems

Cabletron Systems CyberSWITCH CSX150 Bedienungsanleitung

Cabletron Systems

Cabletron Systems MMAC-Plus 9H421-12 Bedienungsanleitung

Cabletron Systems

Cabletron Systems MMAC-Plus 9E423-24 Bedienungsanleitung

Cabletron Systems

Cabletron Systems ESX-1320 Bedienungsanleitung

Cabletron Systems

Cabletron Systems SmartSTACK ELS100-24TXG Bedienungsanleitung

Cabletron Systems

Cabletron Systems bridges Bedienungsanleitung

Cabletron Systems

Cabletron Systems 2H23-50R Bedienungsanleitung

Cabletron Systems

Cabletron Systems MMAC-Plus 9EX02-12 Bedienungsanleitung

Cabletron Systems

Cabletron Systems SynOptics 3000 Series Bedienungsanleitung

Cabletron Systems

Cabletron Systems SmartSwitch 9W006 Bedienungsanleitung

Cabletron Systems

Cabletron Systems TRMIM 24A TRMIM-24A Bedienungsanleitung

Beliebte Schalten Handbücher anderer Marken

URC

URC Total Control MFS-8 Bedienungsanleitung

Azbil

Azbil HPQ-D11 Bedienungsanleitung

Sony

Sony DFS-900M Bedienungsanleitung

SICK

SICK i17S Bedienungsanleitung

F&F

F&F SZR-277 Bedienungsanleitung

Shure

Shure UAMS/BK Bedienungsanleitung

Dräger

Dräger X-zone Switch Off Bedienungsanleitung

Asco

Asco Joucomatic 349 Series Bedienungsanleitung

BT Mini Hub Bedienungsanleitung

D-Link

D-Link DES-1226G Bedienungsanleitung

Johnson Controls

Johnson Controls FS80-C Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Bedienungsanleitung

MicroNet

MicroNet SP1200A Bedienungsanleitung

Ruijie

Ruijie RG-PF2920 Series Installations- und Betriebsanleitung

Altinex

Altinex DA1914SX Bedienungsanleitung

MiLAN

MiLAN MIL-SM2401M Bedienungsanleitung

RJM

RJM MASTERMIND PBC/6X Bedienungsanleitung

Atlas

Atlas MMK-KVM8 Bedienungsanleitung