Canon ImagePROGRAF TX-2000 Betriebsanleitung

QT6-2184-V01 PRINTED IN XXXXXXXXXXXXXXXX © CANON INC. 2017

479

It is recommended that you reserve space of the following dimensions to allow you to work around the printer.

Check the completed image of the printer you purchased and make sure you have enough space to install the printer.

In order to ensure that this product is used safely, be sure to read the precautions.

-> Quick Guide (separate manual)

Before Setting Up the Printer

Read this manual before attempting to operate the printer.

Keep this manual in a handy location for future reference.

Set up the printer using the following procedure.

• Windows is a trademark or registered trademark of Microsoft Corporation in the

U.S. and/or other countries.

TX-2000

Installation space (W x D x H)

• When not using the stand

59.5 x 56.5 x 40.2 inches (1510 x 1434 x 1020 mm)

• When using the stand

59.5 x 66.3 x 61.5 inches (1510 x 1684 x 1560 mm)

TX-3000

Installation space (W x D x H)

70.5 x 66.3 x 61.5 inches (1790 x 1684 x 1560 mm)

TX-4000

Installation space (W x D x H)

78.5 x 66.3 x 61.5 inches (1993 x 1684 x 1560 mm)

Conrming the Installation Space

Overview of Setup

Important

• The printer stand and roll unit may be options depending on the model. Care is required because the required space may differ depending on whether or not the

options are used.

• The space required in front of the printer differs on how the basket supplied with the printer stand is used. This shows the installation space when used in the

position in the illustration.

Caution

• Instructions in this Setup Guide show the TX-4000 printer. Note that your printer may look different from these illustrations in some cases. However, the basic

operations are the same.

RMC (Regulatory Model Code): K10475

RMC (Regulatory Model Code): K10474

RMC (Regulatory Model Code): K10473

If an error message appears during setup or other problems occur,

refer to "Responding to Messages" on p.14.

Setup Guide

Introductory Information

ENGLISH

• Check this also after setup is complete.

3.9 inches

(100 mm)

(When not using

the stand)

3.9 inches (100 mm)

(When using the

stand)

23.6 inches

(600 mm)

(When using the stand)

(When not

using the stand)

5.9 inches (150 mm)

7.9 inches

(200 mm)

7.9 inches

(200 mm)

23.6 inches

(600 mm) 7. 9 inches

(200 mm)

7.9 inches

(200 mm)

23.6 inches

(600 mm)

3.9 inches

(100 mm)

5.9 inches

(150 mm)

7.9 inches

(200 mm)

7.9 inches

(200 mm)

23.6 inches

(600 mm)

3.9 inches

(100 mm)

5.9 inches

(150 mm)

*Assemble the Stand ( P. 3) * Refer to the separate

manual

Attach the Alignment Rod ( P. 3)

Install the Printer ( P. 3)

*Attach the Roll Unit ( P. 5) * Refer to the separate

manual

*Attach the Basket ( P. 5) * Refer to the separate

manual

*Assemble the Stacker ( P. 5) * Refer to the separate

manual

Turn On the Printer ( P. 5)

Install the Ink Tanks(P.7)

Install the Print Head ( P. 9)

Load the Paper (P.10)

Storage Locations (P.13)

How to Display the Online Manuals(P.14)

• Perform Print Head Adjustment

and Select the Connection Method (P.11 ~ 12)

• Connect to the Printer

Package Contents

● Roll Unit

● Stacker

● Printer

Depending on your region, these might be included as standard or they might be available as optional accessories.

Refer to the included setup guides for details on the products included in the boxes.

The Manuals Supplied with This Printer

A. Printer

B. Paper for adjustment

C. Setup Guide (this manual)

D. Starter ink tanks (C, M, Y, MBK, BK)

E. Set of CD-ROMs

F. Set of printer documentation

G. Print head

H. Power cord

I. Holder stopper*

*The holder stopper is used when loading roll paper.

For details, refer to the Online Manual.

S. Rod holder (x 2)

T. Basket arm (x 2)

U. M4 Hex screw for basket arm (x 4)

V. Basket rod / Basket cloth

W. Basket locking support (x 2)

J. Stand leg L

K. Stand leg R

L. Stand stay

M. M4 hex screw (x 9)

N. M8 hex screw (x 4)

O. M8 Allen wrench

P. M4 Allen wrench

Q. Accessory pocket

R. 3-inch paper core attachment (x 2)

Only included with models where the stand is included as standard.

Furthermore, it may be packaged in a separate box depending on the

region where you purchased the printer.

● Basket

These items might not be included depending on your region.

● Stand

Note

• Some items are included with the printer but not described in this manual.

Keep these items in a safe place after setup because they are used in various printing applications.

• For instructions on the included items not described in this manual, refer to the Online Manual. ("How to Display the Online Manuals" on p.14)

• A cable to connect the printer to a computer is not provided with the printer.

Printed Manuals

Setup Guide (this manual)

Describes how to setup the printer.

Quick Guide

Contains information related to warnings for

using this product safely and information related

to replacing paper, ink tanks, and the print head.

Printer Stand Setup Guide*

Roll Unit Setup Guide*

Stacker Setup Guide*

Describes how to assemble the optional accessories.

Electronic Manuals

Online Manual

This manual describes advanced usage of the printer such

as paper saving tips, how to print a poster and banner with

the supplied software and print quality adjusting method, in

addition to the basic instructions for printing on roll paper or cut

sheet.

To view the electronic manuals, refer to "How to Display the

Online Manuals" (p.14).

The following manuals are included with this printer.

* Might not be included depending on your region and selected purchase options.

F E

M, N, O, P, U R

• When using the stand

-> Assemble the stand on which you will install the printer by referring to the Printer Stand Setup Guide (separate manual).

• When not using the stand

-> Proceed to "Install the Printer".

Assemble the Stand

Attach the rod for aligning the printer to the stand.

When using the basket included with the stand When using the stacker

1. Prepare the basket rod (cord side).

2. Hook the basket rod onto the supporting plates of the stand legs.

Attach such that the protrusions (A) on the basket rod are facing

towards you.

1. Open the stacker box and take out rod 2.

2. Hook rod 2 onto the supporting plates of the stand legs. Attach

such that the holes (A) on rod 2 are facing up.

Attach the Alignment Rod

Remove the packaging material.

Remove all of the tape and other packaging material. Open the top

cover (A) and output guide (B), and then remove the tape afxed to

the roll holder.

Install the Printer

With 3 people holding the carrying handles under the printer on both ends, lift the printer.

• Moving the printer requires at least 6 people, 3

on either side. Be careful to avoid back strain and

other injuries due to the weight of the printer.

- TX-4000 : Approx. 211 lb (96 kg)

- TX-3000 : Approx. 191 lb (87 kg)

- TX-2000 : Approx. 163 lb (74 kg)

• When moving the printer, rmly grasp the carrying

handles (A) under each side. Holding the printer at

other positions is dangerous and may cause injury

and damage if the printer is dropped.

• When setting the printer down temporarily, make

sure to put the printer on a at, stable place.

• When standing the printer up, make sure the side

with the control panel is up, and place cardboard

or other material underneath to prevent scratching.

Furthermore, make sure that the weight of the

printer is taken by the corner of the printer. If the

weight is taken by any other part of the printer, the

printer may become damaged.

• When standing up the printer or supporting the

printer, hold the metal parts of the printer. If

you hold a plastic part, the printer may become

damaged.

• Carrying the printer with only the center of the

printer loaded may cause damage to the printer.

Caution

Align the position of the printer.

When using the basket included with the stand When using the stacker

Place the printer on the stand such that the protrusion (A) for aligning

the position of the printer under the rear side of the printer is aligned

with the position of the black marker on the stand rod attached to the

supporting plate.

A A

Place the printer on the stand such that the protrusion (A) for aligning

the position of the printer under the rear side of the printer is aligned

with the position of the holes on rod 2 attached to the supporting

plate.

A A

Important

• If you are not using a stand, place the printer in the installation

location and proceed to "Turn On the Printer".

Important

• If you are not using a stand, place the printer in the installation

location and proceed to "Turn On the Printer".

• When using the roll unit

-> Attach the roll unit to the stand by referring to the Roll Unit Setup Guide (separate manual).

• When not using the roll unit

-> Proceed to "Attach the Basket".

• When using the basket included with the stand

-> Attach the basket to the stand by referring to the Printer Stand Setup Guide (separate manual).

Proceed to "Attach the Basket".

• When not using the basket

-> Proceed to "Assemble the Stacker".

Open the top cover.

Pull up and remove the belt stopper (A).

Note

• Keep the belt stopper you removed for future use. You

will need them in case you move the printer to another

location.

• When you open the top cover, a cleaning brush is

stored on the right side. Take it out and use it when

cleaning inside the top cover.

Attach the Basket

Turn On the Printer

Attach the Roll Unit

• When using the stacker

-> Assemble the stacker by referring to the Stacker Setup Guide (separate manual).

• When not using the stacker

-> Proceed to "Turn On the Printer".

Assemble the Stacker

Afx the printer to the stand.

Remove the alignment rod.

Use an M4 Allen wrench to securely afx three M4 hex

screws each on the left and right from the bottom of the

supporting plate.

Important

• The removed alignment rod will be used when attaching the

basket.

Peel off the tape afxed to the carriage, and then pull the protective

material (A) towards you and remove it. Remove the protective sheet

if there is one attached.

Close the top cover.

Plug the power cord into the power supply connector on the back of the printer.

TX-2000 / TX-3000 TX-4000

Plug the power cord into the outlet.

Turn on the printer.

When the language selection screen appears on the touch screen,

select and tap a language (lightly with your nger, and then move

your nger away). Then, if the screen for selecting a time zone

appears, select and tap your region.

When a message prompting you to start the setup appears on the

touch screen, tap OK.

Shake each ink tank gently 7 or 8 times

before opening its pouch.

Important

• Failure to shake the ink tanks may result

in reduced print quality because ink

ingredients have settled on the bottom

of the tank.

Note

• If the ink tank is cold, allow it to adjust to

room temperature before attaching it to

the printer.

Open the pouch and remove the ink tank.

Important

• Never touch the ink holes (A)

or metal contacts (B). Touching

these parts may cause stains,

damage the ink tank, and

affect print quality.

• Avoid dropping the ink tank

after removing it from the

pouch. Otherwise, ink may

leak and cause stains.

• Do not remove ink tanks to shake them

after they have been mounted. Doing so

may cause ink to spill.

Mount the ink tank in the holder. Install

with the ink holes facing down and the

metal contacts facing away from you.

Important

• An ink tank cannot be mounted in the

holder if it is not oriented correctly for the

color.

• Do not try to force an ink tank into the

holder if it does not go in normally.

Check the color indicated on the label

and the ink tank orientation, and then try

mounting the tank into the holder again.

Instructions on ink tank installation are shown on the screen. Open

the ink tank covers as instructed.

Release the ink tank lock lever for the color of ink to install.

Pull the handle part (A) towards you while pressing the button at

position (B).

Install the 5 ink tanks by following the instructions on the screen.

Install the Ink Tanks

Pull out the ink tank lock lever.

Pull straight up. Pull towards you. Securely lay down at a position where

it does not return when you release

your hand.

Important

• Make sure the ink tank lock lever stays in the locked position.

Lift up the ink tank lock lever once and

then push it down.

Firmly push down the handle part of the

ink tank lock lever all the way in.

Make sure the ink lamp lights red.

Important

• If the ink lamp does not light, repeat

steps 2, 3, 7, and 8.

Repeat steps 2 to 9 to install each of the

ink tanks.

Close the ink tank covers.

When the screen for conrming

installation of the ink tank appears, tap

OK.

When the instruction to open the top

cover appears on the screen, open the

top cover.

Instructions are now shown on the screen

regarding print head installation.

Tilt the print head lock lever towards

you.

Open the print head locking cover by

following the instructions on the screen,

and tap OK.

Do not touch the contacts (A) on the

carriage.

Remove the print head from the bag by

holding the tab parts (A).

Remove the orange protective caps (A

and B). Remove the protective cap (B) by

holding the tab part (C).

B C

Important

• Do not touch the part that was being

protected by the protective cap under

any circumstances. Touching it may

cause damage to the print head or

printing problems.

• The print head contains ink, so be

careful not to spill it once the protective

caps are removed.

• Do not reattach the protective caps

after removing them. Dispose of them

according to local regulations.

Insert the print head into the carriage with the ink holes (A) on the upper side and facing

towards you as shown in the gure. Carefully push the print head rmly into the carriage,

ensuring that the part covered by the protective caps does not touch the carriage.

Pull the print head locking cover down

toward the front to lock the print head in

place.

Push the print head lock lever all the

way to the end.

Close the top cover.

Note

• If the roll unit is installed, the roll unit

calibration starts automatically after the

print head is attached.

If the roll holder is mounted on the roll

unit at this time, calibration cannot be

executed. Do not mount the roll holder

on the roll unit until the setup has

nished.

Install the Print Head

Tap OK.

Tap Manual.

Open the top cover and lift the release

lever.

Important

• Do not touch the linear scale (A),

carriage shaft (B), or ink tube stabilizer

(C). Touching them may cause damage.

ACB

Insert the paper for adjustment between the platen (A) and paper

retainer (B) in portrait orientation with the printed side of the paper

facing up. Only one sheet of paper is needed.

When using the TX-2000 without the printer stand

Important

• Check that there is nothing under the printer.

If there is anything under the printer, it may cause scratches on

the paper or paper jams, and you might not be able to adjust

the print head correctly.

Load the paper aligned with the paper

alignment lines (A) to ensure that the

paper is not crooked, and align the

leading edge of the paper with the front

side of the line (B).

Lower the release lever to lock the paper

and close the top cover.

The screen for selecting the paper type

appears. Tap the type of paper you

loaded.

In this case, tap Coated papers then

Coated papers.

Note

• If The paper is loaded askew. appears,

repeat steps 2 to 5.

Load the paper for adjustment.

Load the Paper

Andere Handbücher für imagePROGRAF TX-2000

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Canon Multifunktionsdrucker Handbücher

Canon

Canon iR3530 Bedienungsanleitung

Canon

Canon Image Runner 2000 Series Bedienungsanleitung

Canon

Canon Color imageCLASS MF8350Cdn Sicherheitsleitfaden

Canon

Canon PIXMA MP470 Bedienungsanleitung

Canon

Canon C4580 Series Bedienungsanleitung

Canon

Canon imageCLASS D680 Montage- und Wartungsanleitung

Canon

Canon IMAGERUNNER 7095 PRINTER Bedienungsanleitung

Canon

Canon MF754Cdw Bedienungsanleitung

Canon

Canon PIXMA MG6120 Series Bedienungsanleitung

Canon

Canon PIXMA MP220 Bedienungsanleitung

Canon

Canon MP730 - MultiPASS Color Inkjet Bedienungsanleitung

Canon

Canon ImageCLASS MF4690 Bedienungsanleitung

Canon

Canon MultiPASS C635 Bedienungsanleitung

Canon

Canon imageRUNNER ADVANCE C3325i Bedienungsanleitung

Canon

Canon PIXMA MP990 Montage- und Wartungsanleitung

Canon

Canon imageCLASS LBP151dw Bedienungsanleitung

Canon

Canon PIXMA MP510 Bedienungsanleitung

Canon

Canon imageRUNNER ADVANCE DX C7780i Bedienungsanleitung

Canon

Canon PIXMA MG7500 Series Einrichtungshandbuch

Canon

Canon ImageRUNNER ADVANCE DX C5760i Installationsanleitung

Canon

Canon imageCLASS D340 Handbuch

Canon

Canon PIXMA MP760 Bedienungsanleitung

Canon

Canon MultiPASS L6000 Bedienungsanleitung

Canon

Canon imageRUNNER 2206N Bedienungsanleitung

Beliebte Multifunktionsdrucker Handbücher anderer Marken

Triumph Adler

Triumph Adler DC 2016 Handbuch

Epson

Epson WorkForce WF-2510 Benutzerhandbuch

Epson

Epson Stylus Scan 2000 Installations- und Betriebshandbuch

Epson

Epson PictureMate Snap PM 240 Bedienungsanleitung

Konica Minolta

Konica Minolta bizhub C35 Bedienungsanleitung

Brother

Brother MFC-J430w Bedienungsanleitung

Konica Minolta

Konica Minolta BIZHUB 558 Bedienungsanleitung

Lexmark

Lexmark MX710 Series Handbuch

Brother

Brother MFC-9760 Bedienungsanleitung

Lexmark

Lexmark XC8155 Bedienungsanleitung

Lexmark

Lexmark X642E Bedienungsanleitung

Sharp

Sharp MX-2310U Leitfaden

Aficio

Aficio 200 Bedienungsanleitung

Ricoh

Ricoh Pro C900 Bedienungsanleitung

Lexmark

Lexmark X925 Bedienungsanleitung

Brother

Brother Business Smart MFC-J4510dw Bedienungsanleitung

Epson

Epson Stylus CX8400 Series Bedienungsanleitung

Oce

Oce VarioLink 5022 Bedienungsanleitung

Canon imagePROGRAF TX-2000 Betriebsanleitung

Beliebte Multifunktionsdrucker Handbücher anderer Marken