Canon PIXMA MX700 Series Bedienungsanleitung

Network Setup Guide

Guide d'installation réseau

Guía de configuración de red

Guia de configuração de rede

QT51387V01

ESPAÑOL

PORT DO BRASIL

ENGLISH

QT5-1387-V01 XXXXXXXX © CANON INC. 2007 PRINTED IN THAILAND

IMPRIME EN THAILANDE

The following ink tanks are compatible with this product.

Les réservoirs d'encre suivants sont compatibles avec ce produit.

Los siguientes depósitos de tinta son compatibles con este producto.

Os cartuchos a seguir são compatíveis com este produto.

www.canon.ca

www.canonlatinamerica.com

FRANÇAIS

ENGLISH

Network Setup Guide

This manual contains the setup information required to use the machine over wired LAN.

If you use the machine with USB connection, refer to your setup sheet.

Introduction

To use the machine connected to a computer, you need to install the software called “MP Drivers” in

the computer.

The following two connection types are described in this manual.

Setting up for use over LAN

When the machine has not been connected to the

network, perform this setup to use the machine over LAN.

This setup procedure requires settings to be performed on

the machine and the computer.

Important

zA hub and LAN cable are required to connect this machine to a LAN. These must be purchased

separately.

zIf the installation and adjustment of the machine have not been finished, refer to your setup sheet to set

up the machine properly.

Note

zThe configuration and the type of the device vary depending on your network environment. For details,

refer to your device’s instruction manual or contact its manufacturer.

zIn an office setup, consult your network administrator.

Note

zTo set up the machine that is not yet connected to a LAN, connect the machine and the computer with a

USB cable.

zEven if the machine has been set up to be used with the USB connection, follow the setup procedure

described in this manual to connect the machine to a LAN for the first time.

ENGLISH

Setting up an additional LAN-connected computer

When the machine has already been set up to connect to

the network using a computer, perform this setup to use

the machine from an additional computer over LAN. This

setup procedure only requires settings to be performed

on the additional computer.

Trademark Notices

z“Microsoft” is a registered trademark of Microsoft Corporation.

z“Windows” is a trademark of Microsoft Corporation, registered in the U.S. and other countries.

z“Windows Vista” is a trademark of Microsoft Corporation.

z“Macintosh” and “Mac” are trademarks of Apple Inc., registered in the U.S. and other countries.

ENGLISH

Confirming the Network Environment

zTurn off the firewall function temporarily or change its setting. If you disable the firewall function,

disconnect your network from the Internet.

zMake sure that the configuration of computers, hubs, and other network devices is complete, and

computers can connect to the network.

Important

After setup is complete, turn back on any security functions you disabled for setup.

If you connect to a network that is not protected with security measures, there is a risk of disclosing data

such as your personal information to a third party.

Note

zFor information on the firewall function of your security software, refer to its instruction manual or

contact its manufacturer.

zIn an office setup, consult your network administrator.

zIf you are using Windows®

See “Setting Up the Machine and the Computer (Windows)” on page 4.

zIf you are using Macintosh®

See “Setting Up the Machine and the Computer (Macintosh)” on page 17.

ENGLISH

Setting Up the Machine and the Computer

(Windows)

zBefore installing the MP Drivers, disable all anti-virus programs and automatically loading

programs.

zLog into a user account with the administrator privilege.

zA message asking for your confirmation to restart your computer may appear during the

installation process. If this message is displayed, follow the on-screen instructions and click OK.

The installation resumes from where it left off when your computer has been restarted. While

restarting, do not remove the Setup CD-ROM.

1 Installing the software

1Turn off the machine.

2Turn the computer on and start Windows.

Important

Depending on the country or region of purchase, the following two CD-ROMs are included in the package

for the Windows setup.

– Windows (CD-1)

– Windows (CD-2) Macintosh

In this case, insert the Setup CD-ROM “Windows (CD-1)” first to start the installation, and follow the on-

screen instructions to complete the installation.

Note

The screens below refer to Windows Vista™ operating system Ultimate Edition (hereafter referred to as

“Windows Vista”) installation. Screens may vary depending on the operating system you are using and

also depending on the country or region of purchase.

Note

If the Found New Hardware or Found New Hardware Wizard

screen appears automatically during the installation process,

remove the USB cable connected to your computer. Click Cancel

to quit the screen. In Windows Vista, the screen may close

automatically when the USB cable is unplugged. Then turn off the

machine and proceed from step 3 to install the MP Drivers.

Note

Make sure that the Power lamp is turned off.

ENGLISH

3Insert the Setup CD-ROM.

The setup program should run automatically.

In Windows Vista, go to step 4.

In Windows XP and Windows 2000, go to step 6.

4If the AutoPlay screen appears, click Run

Msetup4.exe.

5If the User Account Control screen appears,

click Continue.

If the same screen reappears in subsequent steps,

click Continue.

6When the screen shown on the right appears,

click Easy Install.

The MP Drivers, On-screen Manuals, and

application software are installed automatically.

Important

If two CD-ROMs are included in the package for the

Windows setup, insert the Setup CD-ROM “Windows

(CD-1)”.

Note

zIf the Select Language screen appears, select a

language, then click Next.

zIf the Select Your Place of Residence screen

appears, select your place of residence, then click

Next.

Note

If you want to select particular items to install, click

Custom Install and follow the on-screen instructions

to proceed with the installation.

ENGLISH

7When the Easy Install screen appears,

confirm the contents, then click Install.

8Read the License Agreement carefully and

click Yes.

Installation of the MP Drivers, On-screen Manuals,

and application software will begin.

The software installation screen may appear during

the installation process. Follow the on-screen

instructions to install the software.

9Confirm the connection type.

The next procedure varies depending on how you

intend to connect the machine and the computer.

Note

zMove the cursor over items to display

explanations of each application.

zThe list of applications may vary depending on the

country or region of purchase.

Users in Asia

zScan Soft OmniPage SE can be installed only on

an English operating system.

See “2-A Setting up for use over LAN” on page 7.

See “2-B Setting up an additional LAN-connected computer”

on page 12.

To use a USB connection, refer to your setup sheet.

Setting up for use over LAN

Setting up an additional LAN-connected computer

ENGLISH

2-A Setting up for use over LAN

This section describes how to set up the machine to be used over wired LAN, when the machine has

not been connected to the network. This setup procedure requires settings to be performed on the

machine and the computer.

1On the Setup Method screen, select Set up

the printer and the computer for network

use, then click Next.

2When the Printer Connection screen

appears, connect the machine to the

computer with a USB cable, then turn on the

machine.

When the machine is turned on, the Power lamp

lights up green. When the computer detects the

machine, the next screen will appear automatically.

When using Windows 2000:

When you connect the machine to the computer

with a USB cable, a message asking for your

confirmation to restart your computer is displayed.

Click Yes. Then when an error message is

displayed, click OK to proceed with the installation.

3When the Setup Preparations dialog box

appears, confirm that preparation is

complete, then click Next.

Note

If you select Use the printer via USB, the machine is

set up to be used with USB connection.

Note

zTo set up the machine that is not yet connected to a

LAN, connect the machine and the computer with a

USB cable.

zIf you cannot go to the next procedure after 3

minutes, refer to “Cannot Install the MP Drivers” in

“Troubleshooting” in the User’s Guide on-screen

manual.

Note

If the machine’s network settings are already

configured, the Setup Environment Confirmation

dialog box appears asking for your confirmation to use

the machine with the current settings. You can

proceed with the setup using the current network

settings. To do so, click Use it as is. To reconfigure the

network settings, click Reconfigure.

ENGLISH

4When the Check Wired LAN Connection

dialog box appears, remove the LAN

connector cap, connect the machine to the

network devices such as hubs with a LAN

cable, then click Yes.

(A) Wired LAN connector

5Confirm that the setup program detects the

machine automatically.

The machine connected with the USB cable is

detected automatically via LAN connection.

In Windows Vista, go to step 7.

In Windows XP and Windows 2000, go to step 6.

6When the Network Setup of the Card Slot

dialog box appears, specify the drive letter,

then click Next.

Note

The connection may vary depending on your network

environment.

Note

If the machine was not detected, the Set Printer IP

Address dialog box appears. Make sure of the

following, then click Connect.

zThe network devices such as hubs or routers are

turned on, and the machine and the computer are

connected to the network.

zThe machine is connected to the computer with the

USB cable.

zThe IP address to be set for the machine is

displayed on the Set Printer IP Address dialog

box. If it is different from the address you want to

set for the machine, enter the desired IP address

on the Set Printer IP Address dialog box.

(If the machine is turned off, the Set Printer IP

Address dialog box does not appear.)

If it still fails, see “The Set Printer IP Address dialog

box is displayed during setup” on page 29.

Note

The Card Slot of the machine must be mounted to

be used as the memory card drive of the LAN-

connected computer.

To write files to a memory card, set the Read/write

attribute setting under Device settings to LAN

enabled. If the setting is set to USB enabled, you

cannot access the network drive of the Card Slot.

(A)

Andere Handbücher für PIXMA MX700 Series

Inhaltsverzeichnis

Sprachen:

Andere Canon Multifunktionsdrucker Handbücher

Canon

Canon MultiPASS F60 Sicherheitsleitfaden

Canon

Canon PIXMA MG5520 Bedienungsanleitung

Canon

Canon imageRUNNER ADVANCE C5255 Bedienungsanleitung

Canon

Canon PIXMA MP495 Series Bedienungsanleitung

Canon

Canon MX390 series Einrichtungshandbuch

Canon

Canon imageRUNNER C3480 Bedienungsanleitung

Canon

Canon G4000 series Einrichtungshandbuch

Canon

Canon MAXIFY MB5150 Einrichtungshandbuch

Canon

Canon imageRUNNER ADVANCE 6075 Series Bedienungsanleitung

Canon

Canon iR2020 Series Produktinformationsblatt

Canon

Canon imageRUNNER 85 Bedienungsanleitung

Canon

Canon LaserCLASS 310 Kurzanleitung

Canon

Canon imageRUNNER 1750iF Sicherheitsleitfaden

Canon

Canon MG5200 series Bedienungsanleitung

Canon

Canon PIXMA MG6320 Handbuch

Canon

Canon MF465dw Bedienungsanleitung

Canon

Canon imageRUNNER C3120 Bedienungsanleitung

Canon

Canon PIXMA MX860 series Bedienungsanleitung

Canon

Canon imageRUNNER ADVANCE DX 4845i Bedienungsanleitung

Canon

Canon LASERBASE MF5700 Series Bedienungsanleitung

Canon

Canon PIXMA MG4220 Bedienungsanleitung

Canon

Canon TS6420a Einrichtungshandbuch

Canon

Canon IMAGERUNNER 7095 PRINTER Bedienungsanleitung

Canon

Canon SmartBase 1270D Bedienungsanleitung

Beliebte Multifunktionsdrucker Handbücher anderer Marken

Triumph Adler

Triumph Adler DC 2016 Handbuch

Epson

Epson WorkForce WF-2510 Benutzerhandbuch

Epson

Epson Stylus Scan 2000 Installations- und Betriebshandbuch

Epson

Epson PictureMate Snap PM 240 Bedienungsanleitung

Konica Minolta

Konica Minolta bizhub C35 Bedienungsanleitung

Brother

Brother MFC-J430w Bedienungsanleitung

Konica Minolta

Konica Minolta BIZHUB 558 Bedienungsanleitung

Lexmark

Lexmark MX710 Series Handbuch

Brother

Brother MFC-9760 Bedienungsanleitung

Lexmark

Lexmark XC8155 Bedienungsanleitung

Lexmark

Lexmark X642E Bedienungsanleitung

Sharp

Sharp MX-2310U Leitfaden

Aficio

Aficio 200 Bedienungsanleitung

Ricoh

Ricoh Pro C900 Bedienungsanleitung

Lexmark

Lexmark X925 Bedienungsanleitung

Brother

Brother Business Smart MFC-J4510dw Bedienungsanleitung

Epson

Epson Stylus CX8400 Series Bedienungsanleitung

Oce

Oce VarioLink 5022 Bedienungsanleitung