Canon I860 Series Bedienungsanleitung

REFILLING CANON PRINTERS

i860 and similar.

In the past I’ve owned several Epson, H.P, and one

Lexmark printer. With this Canon i860 I think I’ve found the

first consumer friendly printer, and that’s saying a lot.!!!!

This printer has an ink cartridge that can be removed

entirely for cleaning in about two seconds after the ink

tanks have been taken out, and it only take a couple of

seconds to remove all five of those. The cartridge case

can be easily cleaned by soaking in Windex or a mild

ammonia solution. How good can this get!!!!

As far as filling the ink tank with bulk ink, I’ve found there’s

a lot of confusion out there. I’ve found a way to fill these

tanks without leaking and with an easy technique, so this

is to share that with you.

TO BEGIN

Tools:You’ll need the following tools to do this job. Just

about everyone has these except maybe the glue gun.

Drill motor and a very small drill a bit larger than the

diameter of the fill needle.

Hot glue gun and glue (of course)

Bulk ink refilling kit (from Atlascopy.com--of course)

Ink (Same as above)

Newspapers (in case you make a mess first time)

And that’s about it!

THE INK TANKS

These aren’t cartridges, they’re tanks, which means there

is no sophisticated controllers built in, they’re only simple

tanks to hold ink. The ink comes out the bottom past a felt

lined round hole and into the cartridge (which does have

all those important controllers) and then to the paper.

The tanks have two internal spaces, one is filled with foam

and the other empty. There’s a transit space between the

two spaces for the ink to move from the empty space (a

reservoir) to the foam filled space. The computer uses

infra red technology to read the tanks and can report the

amount of ink remaining to you using the software “setup

utility). Another nice feature is the fact that the tanks are

clear plastic, so you can find out how low the ink is just by

taking out the tanks and looking at them.

Important: Don’t confuse the two black tanks! The large

tank “BK3e” is pigmented ink. It’s used primarily for text.

The smaller black tank “BK6” is dye based and is used for

photo. Don’t put pigmented ink into the small tank--it won’t

work! You may wind up buying a new cartridge!!!

HERE WE GO!!!

First, have the syringe laying down in front of you already

filled with the ink of choice, your rubber gloves on, paper

down on the table, and a sink nearby. You’ll need to

carefully clean the syringe after each fill in order to prevent

cross contamination. Have the drill handy to pick up with

the drill inserted. Have the glue gun hot and ready to go.

METHOD

You’ll need to drill two holes, one in each of these spaces,

on the top of each. Drill the first above the foam filled area

and slightly down into the foam to be sure there’s a clear

passage for venting. This prevents something called

“vapor locking” which won’t allow any ink to leave from the

bottom.

NEXT,

With your rubber gloves on, put your finger over the exit

hole on the bottom below the foam filled space. Hold it

tight! Now drill another hole on the top of the empty

reservoir near the front. You’ll see a slight dimpled spot

almost to the front. Drill there. Now you’re ready to insert

the ink. Pick up the syringe and fill the space almost to the

top. If there’s any ink at all on the top near the hole, wipe it

off with a paper towel, pick up the glue gun and spread a

bit of hot glue over and slightly around the hole. This is the

“fill hole”---not the vent hole over the foam area.

Continue to hold your finger over the exit till the glue sets

up and you’re done. How easy was that????

Once you’re set up it shouldn’t take more than fifteen or

twenty minutes to fill all the tanks even including cleanup.

It’ll go quicker after the first time as the holes are already

drilled. In future fills it’ll be necessary to clear the hole

each time over the reservoir in order for the needle to

enter. Generally that will mean using the drill again as the

glue will go down into the hole a bit.

If you don’t get a good seal with the glue over the fill hole,

ink will immediately begin to run out of the exit hole on the

bottom. I tried using electrical tape as others have

suggested, and even though it was applied very tightly, it

didn’t seal. The glue does, and is easy to use. Only

problem with it is the need to clear the fill hole each time

you want to refill. The tape would have been more

convenient, but that’s the way it goes!!!

Caveat:

I haven’t tried this with any other Canon printer so can’t

vouch for this method with any other than the i860. Seems

that it ought to work on any with this tank system though,

but you’ll have to try for yourselves.

Good printing :-)

Ted Johnson

Andere Handbücher für i860 Series

Inhaltsverzeichnis

Andere Canon Drucker Handbücher

Canon

Canon MAXIFY GX4000 Series Einrichtungshandbuch

Canon

Canon TS3300 Series Bedienungsanleitung

Canon

Canon imagePROGRAF iPF6300S Benutzerhandbuch

Canon

Canon LBP-3260 Bedienungsanleitung

Canon

Canon PIXMA iP6000D Konfigurationshandbuch

Canon

Canon imageRUNNER C3222L Bedienungsanleitung

Canon

Canon imageRUNNER ADVANCE C356iF III Installationsanleitung

Canon

Canon ImageCLASS LBP200d Bedienungsanleitung

Canon

Canon Pixma iP4300 Series Bedienungsanleitung

Canon

Canon S800 Bedienungsanleitung

Canon

Canon iPF655 - imagePROGRAF Color Inkjet Printer Bedienungsanleitung

Canon

Canon imageRUNNER ADVANCE C5500 Series Bedienungsanleitung

Canon

Canon PIXMA MX350 Bedienungsanleitung

Canon

Canon 7611A001 - S 330 Color Inkjet Printer Benutzerhandbuch

Canon

Canon i560 Series Konfigurationshandbuch

Canon

Canon LBP-3000 Bedienungsanleitung

Canon

Canon TS3100 Series Einrichtungshandbuch

Canon

Canon imageCLASS LBP161dn+ Bedienungsanleitung

Canon

Canon TB-206 Bedienungsanleitung

Canon

Canon Color Bubble Jet BJC-8200 Bedienungsanleitung

Canon

Canon PIXMA G6010 Bedienungsanleitung

Canon

Canon Pixma MG6821 Einrichtungshandbuch

Canon

Canon IR 2420 Bedienungsanleitung

Canon

Canon BJ-230 Bedienungsanleitung

Beliebte Drucker Handbücher anderer Marken

Lexmark

Lexmark 1400 Series Handbuch

Evolis

Evolis Elypso Bedienungsanleitung

Kyocera

Kyocera FS-9530DN Bedienungsanleitung

Samsung

Samsung BIXOLON SRP-350plusF Bedienungsanleitung

Dell

Dell Color Laser Printer 2130cn Bedienungsanleitung

Tektronix

Tektronix Phaser 840 Bedienungsanleitung

Epson

Epson ET-7750 Betriebsanleitung

Eltron

Eltron P210 Guide Bedienungsanleitung

Ricoh

Ricoh MD-P1 Bedienungsanleitung

Epson

Epson SC-F7100 series Bedienungsanleitung

Epson

Epson Stylus C40UX Bedienungsanleitung

IRA3D

IRA3D POETRY4 Bedienungsanleitung

Ricoh

Ricoh Aficio AP400 Bedienungsanleitung

BIXOLON

BIXOLON SRP-352plusV Bedienungsanleitung

Epson

Epson Stylus Photo PX700W Montageanleitung

Ricoh

Ricoh SP204SF Bedienungsanleitung

Star Micronics

Star Micronics futurePRNT TSP100 Bedienungsanleitung

Epson

Epson TM-TM88V-i Gebrauchs- und Pflegehandbuch

Canon i860 Series Bedienungsanleitung

Beliebte Drucker Handbücher anderer Marken