Canon imagePRESS Server G100 Bedienungs- und Wartungshandbuch
ENGLISH 日本語
imagePRESS Server G100 Installation Procedure
imagePRESS Server G100 設置手順書
This installation procedure is written in Japanese and English. The installation procedure for Japan model is described in Japanese and one for the other models is
described in English. These procedures are different from each other. Follow the procedure corresponding to the installed model.
- Japanese: The installation procedure for Japan model
- English: The installation procedure for the other models except for Japan model
この設置手順書には、和文と英文の設置手順が記載されている。和文では日本モデル用の設置手順が記載されており、英文では日本モデル以外のその他のモデル用の設
置手順が記載されている。それぞれの設置手順は異なっているので、モデルに応じた手順に従うこと。
・和文： 日本モデル用設置手順
・英文： 日本モデル以外のその他のモデル用設置手順
PRINTED IN USA 45128775 PUB No. FT2-0109-000
© CANON INC. 2014
2
2
Before Connection > Installing the license
Before Connection > Installing the license
How to Check this Installation Procedure
Symbols in the Illustration
The frequently-performed operations are described with symbols in this procedure.
1x 1x 1x
Install
Screw
Packaged Item Remove Tighten Loosen
1x
Connect
Connector
Disconnect
Install
Harness
(Common for Guides and Clamps)
Remove
1x 1x
1x 1x
Connect
Power Cord
Disconnect
Check visuallyCheck the sound Check
OFF Cleaning
ON Push
Power
Unused Parts
F-1-1
Before Connection
Installing the license
Be sure to take out the license certicate included in the package and obtain the license key
in advance. Make the setting of the EFI Controller by the Web browser in the Control Panel.
Register the license by the following procedure.
1) Log in to the host machine as an administrator (mode).
Factory default password is as follows.
• System administration division ID: 7654321
• System administration password: 7654321
CAUTION:
When [System Manager Information Settings] is set, it is required to log in as a system
manager in accordance with instructions from the user administrator.
2) Select Settings/Registration > [Management Settings] > [License/Other] > [Register
License].
3) Enter the license key of the Web browser.
Example: 8888-7777-6666-5555-4444-3333
4) Press [Start] > [OK].
5) Turn OFF and then ON the main power switch to determine the registration.
3
3
Checking the Contents
Checking the Contents
The IP addresses for communication between the host
machine and server are set automatically
1) Enter the Service Mode (level 1).
2) Select: COPIER > OPTION > INT-FACE > IMG-CONT > "3".
3) Exit the Service Mode.
Securing space for installation
A space of 200 mm or more is required from the back of this equipment.
200mm or more
Rear
Equipment
Front
Checking the Contents
NOTE:
[3] Power Cord: The connector has a different shape depending on locations.
Use the correct power code to match the location/area of installation.
Make sure not to leave unused power code at the site.
The parts ([10] to [12], and [13] to [16]) are packed in single bags.
• [10] to [12]: To be used when installing the Open I/F PCB.
• [13] to [16]: To be used when installing the PS Unit.
F-1-2
Europe X2
USA X 1
[1] PS Unit X 1 [3] Power Cord X 1[2] PS Unit Fixation Plate
X 1
[4] Cross Ethernet
Cable X 1
[6] Open I/F PCB X 1
[7] Support Plate X 2 [8] Interface Cable
(1.0 m) X 1
[10] Open I/F PCB
Mounting Plate X 1
[11] Card Spacer X 1 [12] Screw (TP; M3x6) X 4
[5] Shield Ethernet
Cable (3.0 m) X1
[9] License Access
Number Certificate X 1
F-1-3
4
4
Installation Outline Drawing
Installation Outline Drawing
Use 2 of them
[13] Wire Saddle X 4 [15] Stepped Screw
(M4) X 2
[14] Screw with
Toothed Washer
(Binding; M4x8) X 4
[16] Screw (TP; M3x6) X 6
< CD/Guides >
• Media Pack
• QUICK SETUP POSTER
F-1-4
Turning OFF the power of the host machine
Check that the main power switch is OFF.
1) Turn OFF the main power switch of the host machine.
2) Be sure that display in the Control Panel and the lamp of the main power supply are turned
off, then disconnect the power plug.
Check when Connecting the Power Plug to an Outlet
When connecting the power plug of this equipment to an outlet, be sure to use an outlet of a
system different from that of the host machine.
Installation Outline Drawing
F-1-5
5
5
Installation Procedure > Installing the Open I/F PCB
Installation Procedure > Installing the Open I/F PCB
Installation Procedure
Installing the Open I/F PCB
1) Remove the Box Left Cover.
• 4 Screws
4x
F-1-6
2) Disconnect the Reader Communication Cable and release the 2 Lock Levers.
1x
3) Hold the grip to remove the Main Controller PCB 2.
• 2 Screws
2x
F-1-7
F-1-8
6
6
Installation Procedure > Installing the Open I/F PCB
Installation Procedure > Installing the Open I/F PCB
4) Remove the Face Plate (the removed Face Plate will not be used).
• 2 Screws (The removed screws will be used in step 8.)
NOTE:
Ask the user to store the Face Cover, in case it is needed in the future.
2x
5) Remove the screw and replace it with the Card Spacer (the removed screw will be used in
step 8).
1x
F-1-9
F-1-10
6) Remove the Bypass PCB (the removed Bypass PCB will not be used).
• 2 Screws (The removed screws will be used in step 8.)
• 1 Connector
NOTE:
Ask the user to store the Bypass PCB, in case it is needed in the future.
2x
1x
7) Install the Open I/F PCB Mounting Plate.
• 1 Screw (TP; M3 x 6)
1x
TP
M3x6
F-1-11
F-1-12
7
7
Installation Procedure > Installing the Open I/F PCB
Installation Procedure > Installing the Open I/F PCB
8) Install the Open I/F PCB.
• 1 Connector
• 5 Screws (Use the screws removed in steps 4, 5, and 6.)
• 3 Screws (TP; M3 x 6)
TP
M3x6
2x
6x
1x
9) Release the 2 Lock Levers in the direction of the arrows, and uniformly push in the Main
Controller PCB 2 with both hands until it stops.
CAUTION:
Install the Main Controller PCB 2 while paying attention not to trap cables.
Lock
Lever
F-1-13
F-1-14
10) Turn over the 2 Lock Levers, and push in and secure the Main Controller PCB 2.
• 2 Screws (Install in order of bottom and top.)
CAUTION:
Be sure to perform the work in the order from 1 to 5 in the gure because the connector
of the Main Controller PCB 2 may not be connected.
2x
11) Connect the Reader Communication Cable.
12) Connect the Interface Cable to the Open I/F PCB.
1x
F-1-15
F-1-16
8
8
Installation Procedure > Installing the PS Unit
Installation Procedure > Installing the PS Unit
13) Put the Interface Cable through the hole of the Box Left Cover to install the Box Left
Cover.
• 4 Screws
CAUTION:
When installing the Box Left Cover, be careful not to trap cables.
4x
F-1-17
Installing the PS Unit
1) Remove the 2 Face Seals of the Rear Upper Cover and loosen the 2 Screws.
(the removed Face Seals will not be used)
2x
2) Hook the Support Plate to the screw (right side) loosened in step 1, and install it in the
direction of the arrow..
• 1 Screw (TP; M3 x 6)
1x
Screw
Screw Support Plate
TP
M3x6
F-1-18
F-1-19
9
9
Installation Procedure > Installing the PS Unit
Installation Procedure > Installing the PS Unit
3) Hook the Support Plate to the screw (left side) loosened in step 1, and install it in the
direction of the arrow.
• 1 Screw (TP; M3 x 6)
Screw
Screw
Support Plate
1x
TP
M3x6
4) Tighten the 2 screws loosened in step 1.
Screw
2x
F-1-20
5) Install the 2 Stepped Screws (M4) to the Support Plate.
Support Plate
Support Plate
Stepped Screw
Stepped Screw
2x
Stepped Screw
M4
6) Remove the 8 screws of the PS Unit. (the removed screw will be used in step 7)
8x
F-1-21
F-1-22
10
10
Installation Procedure > Installing the PS Unit
Installation Procedure > Installing the PS Unit
7) Install the PS Unit Fixation Plate.
• 4 Screw (Use the screws removed in steps 6.)
CAUTION:
Be sure to install it in the correction direction.
4x
8) Hook the PS Unit to the 2 Stepped Screws (M4) tightened in step 5, and install it.
• 4 Screws with Toothed Washer (Binding; M4 x 8)
Screw with
Toothed Washer
Binding; M4x8
4x
F-1-23
F-1-24
9) Remove the 2 Face Seals of the Rear Lower Cover (the removed Face Seals will not be
used).
10) Install the 4 Wire Saddles.
F-1-25
F-1-26
Inhaltsverzeichnis
Andere Canon Drucker Handbücher
Canon
Canon i475D Series Konfigurationshandbuch
Canon
Canon Pixma E3400 Series Bedienungsanleitung
Canon
Canon PIXMA MX712 Bedienungsanleitung
Canon
Canon imagePROGRAF iPF680 Bedienungsanleitung
Canon
Canon BJC-2100 Series Bedienungsanleitung
Canon
Canon iP3000 - PIXMA Photo Printer Handbuch
Canon
Canon i250 Series Bedienungsanleitung
Canon
Canon BJC 210 - Color Inkjet Printer Bedienungsanleitung
Canon
Canon TS8250 Einrichtungshandbuch
Canon
Canon i860 Series Bedienungsanleitung
Canon
Canon imageRUNNER ADVANCE DX C477iFZ Installationsanleitung
Canon
Canon PowerShot S330 Digital ELPH Bedienungsanleitung
Canon
Canon MG3600 series Bedienungsanleitung
Canon
Canon PIXMA iX6520 Bedienungsanleitung
Canon
Canon MG5100 series Bedienungsanleitung
Canon
Canon imageRUNNER ADVANCE DX 4700 Series Bedienungsanleitung
Canon
Canon ImageRUNNER C1538iF Bedienungsanleitung
Canon
Canon iP4200 - PIXMA Photo Printer Bedienungsanleitung
Canon
Canon Folder Professional 6011 Bedienungsanleitung
Canon
Canon SELPHY CP770 Bedienungsanleitung
