Canon DR 3060 - Duplex Scanner Betriebsanleitung

Maintenance Guide

46 Regular Maintenance

Regular Maintenance

Clean the scanner on a regular basis as described below in order to maintain

peak scanning quality.

CAUTION

For safety's sake, always turn the unit off and unplug the power

cord before cleaning this unit.

Cleaning the Scanner

To clean the exterior of the scanner, dampen a cloth with water or a mild

detergent, wring the cloth out thoroughly, and then wipe the dirt away. Then

use a dry cloth to wipe away any moisture.

CAUTION

Never use paint thinner, alcohol, or other organic solvents to

clean the scanner. Such solvents can damage or discolor the

exterior of the scanner. They also create a risk of fire and electric

shock.

Regular Maintenance 47

Cleaning the Scanning Glass and the Rollers

Turn the power off and unplug the power cord from the power outlet.

If the document eject tray extension is open, close it.

Grasp the upper unit and gently lift it up as far as it will go.

Wipe the scanning glass (the shaded portion ■in the illustration) with a clean,

dry cloth.

CAUTION

There is scanning glass on the top and on the bottom. Wipe both

clean. Do not spray the glass directly with water or mild

detergent. Doing so could damage the light source or other

precision optical components.

Using a cloth that has been dampened with water, clean the rollers (the shaded

portion ■in the illustration), rotating them as you wipe them with the cloth.

Note that the rollers labeled ➀, ➁, and ➂in the diagram should only be

rotated in the direction indicated. Then use a clean, dry cloth to wipe away

any moisture.

48 Troubleshooting

Troubleshooting

This section describes common problems that may occur while you are using

the scanner, and how to resolve them.

Refer to the troubleshooting section related to the problem that you have

encountered.

The scanner does not turn on ..................................................... P.48

The PC does not recognize the scanner..................................... P.49

Images are not scanned ............................................................... P.51

Documents do not feed properly................................................. P.51

Resulting scanned images are not correct ................................ P.52

If after consulting the above section you still cannot resolve the problem,

contact your dealer or your service representative.

✘The scanner does not turn on

Check the following:

●Is the power switch in the ON position?

●Is the power cord connected to the scanner securely?

●Is the power cord plugged into an outlet?

Troubleshooting 49

✘The PC does not recognize the scanner

The following are possible causes of the PC failing to recognize the scanner.

Check each possible cause.

Cause The scanner is not connected correctly.

Action Check all of the SCSI cable connections between the scanner, the

SCSI host adapter in the PC, and any other SCSI devices

connected to the system.

Cause The SCSI host adapter is not installed in the PC correctly.

Action Refer to the instruction manual for the SCSI host adapter and

install the SCSI host adapter in the PC correctly.

Also check the following, depending on which operating system

you are using:

Windows 95/98/Me

Click Start - Settings - Control Panel - System - Device Manager,

and make sure that no “x” or “!” symbol appears next to the SCSI

Controller entry. If either of these symbols is displayed, refer to

the instruction manual for the SCSI host adapter and redo the

settings for the SCSI host adapter.

Windows NT 4.0 Workstation

Click Start - Settings - Control Panel - SCSI Adapter, and make

sure that the system recognizes the SCSI host adapter properly. If

the system is not recognizing the SCSI host adapter properly,

refer to the instruction manual for the SCSI host adapter and redo

the settings for the SCSI host adapter.

Windows 2000 Professional

Click Start - Settings - Control Panel - System - Hardware -

Device Manager, and make sure that no “x” or “!” symbol

appears next to the SCSI Controller entry. If either of these

symbols is displayed, refer to the instruction manual for the SCSI

host adapter and redo the settings for the SCSI host adapter.

Windows XP

Click Start - Control Panel - Performance and Maintenance -

System - Hardware - Device Manager, and make sure that no “x”

or “!” symbol appears next to the SCSI Controller entry. If either

of these symbols appears, refer to the instruction manual for the

SCSI board and reconfigure the SCSI board.

50 Troubleshooting

Cause The scanner's SCSI ID is identical to the SCSI ID of

another device.

Action Check the SCSI IDs of all SCSI devices connected to the system

and set a unique SCSI ID for the scanner.

Cause The terminator is not set correctly.

Action Connect a terminator to the SCSI device that is at the end of the

SCSI daisy chain. If the SCSI device has a built-in terminator

function, enable the terminator.

Cause The PC was turned on before the scanner.

Action Shut down both the PC and the scanner, and then turn the scanner

back on, followed by the PC.

Cause The scanner is not on.

Action Refer to the previous section, "The scanner does not turn on," and

check to see if the scanner is on. If the scanner is not on, shut

down the PC, then turn the scanner on first, and then the PC.

Cause The SCSI host adapter is not compatible with the scanner.

Action Use a SCSI host adapter that is compatible with the scanner

driver and your application software.

Cause In Windows NT 4.0 Workstation, Windows 2000

Professional or Windows XP, the ASPI manager has not

been installed correctly.

Action Following the instructions in the SCSI host adapter instruction

manual, install the ASPI manager and then start up the ASPI

manager.

Troubleshooting 51

✘Images are not scanned

Check the following if the scanner does not scan an image even though the

scanning operation is being performed:

●Is the scanner connected to the PC correctly?

●Has the scanner driver been installed?

●Has the application software been installed correctly? Has the application

software been set up correctly?

●Is there a problem in the PC system?

Notice

If the scanner will not respond at all due to a system error, turn the scanner

off, wait at least 10 seconds, and then turn the scanner back on again.

When you resume scanning, make sure that the last document was scanned

correctly.

✘Documents do not feed properly

The following are possible causes of a document failing to feed properly.

Check each possible cause.

Cause An attempt is being made to scan a document of a size,

thickness or weight that the scanner cannot scan.

Action Check the size, thickness and weight of the document. For

cautions concerning documents, refer to "Documents" on

page 30.

Cause The rollers inside the scanner are dirty or worn.

Action Clean the rollers as described on page 47. If the rollers are worn,

contact your service representative and request to have the rollers

replaced.

For details on how to clear jammed paper, refer to "Clearing a Paper Jam" on

page 43.

52 Troubleshooting

✘Resulting scanned images are not correct

If the resulting scanned images are not crisp, if there are lines or spots on the

image, or if there is some other problem with a scanned image, likely causes

are listed below. Check each item and take the appropriate action.

Cause The scanning glass or the rollers inside the scanner are dirty.

Action Clean the scanning glass and rollers as described on page 47.

Cause The application software is not set up properly for

scanning.

Action Check the scanning-related settings, such as "brightness," in the

application software.

For example, if the document cannot be scanned at all, it is

possible that the "brightness" setting is too high. If the resulting

scanned image is too dark, it is possible that the "brightness"

setting is too low.

Cause The scanner driver or application software is not running

normally.

Action If the software is set properly for scanning and normal scanning

is still not possible, it is possible that the scanner driver or the

application software is not running normally. Re-install the

scanning driver or the application software. For details on how to

install the scanner driver, refer to page 24. For details on how to

install the application software, refer to the application software

instruction manual.

Cause An attempt was made to use a function of the scanner that

is not supported by the application software.

Action Some application software may not support certain functions,

such as automatic paper size detection and user-specified

margins. Using such application software for scanning may yield

abnormal scanning results. Try scanning without using functions

such as automatic paper size detection or margins settings.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Canon Scanner Handbücher

Canon

Canon imageFORMULA DR-2080C Bedienungsanleitung

Canon

Canon CR-50 Bedienungsanleitung

Canon

Canon DR 7090C - imageFORMULA - Document Scanner Bedienungsanleitung

Canon

Canon Microfilm Scanner 800II Bedienungsanleitung

Canon

Canon CanoScan FB 1200S Bedienungsanleitung

Canon

Canon imageFormula DR-6010C Bedienungsanleitung

Canon

Canon imageFORMULA DR-2580C Bedienungsanleitung

Canon

Canon imageFormula DR-C225 Bedienungsanleitung

Canon

Canon ScanFront 300 Bedienungsanleitung

Canon

Canon DR 5010C - imageFORMULA - Document Scanner Gebrauchsanweisung

Canon

Canon CanoScan D1230UF Bedienungsanleitung

Canon

Canon Microfilm Scanner 300 Bedienungsanleitung

Canon

Canon imageFORMULA DR-M160II Bedienungsanleitung

Canon

Canon imagePROGRAF L24e Bedienungsanleitung

Canon

Canon GC-201 Bedienungsanleitung

Canon

Canon M181011 Bedienungsanleitung

Canon

Canon N1240U - CanoScan Flatbed Scanner Bedienungsanleitung

Canon

Canon CanoScan FB 1200S Bedienungsanleitung

Canon

Canon imageFORMULA CR-L1 Bedienungsanleitung

Canon

Canon imageFORMULA DR-M160II Bedienungsanleitung

Canon

Canon L1 Bedienungsanleitung

Canon

Canon imageFORMULA DR-2580C Gebrauchsanweisung

Canon

Canon 8600F - CanoScan Bedienungsanleitung

Canon

Canon imageFORMULA DR-1210C Bedienungsanleitung

Beliebte Scanner Handbücher anderer Marken

Plustek

Plustek Scanner Bedienungsanleitung

Z/I Imaging

Z/I Imaging PhotoScan 2001 Bedienungsanleitung

Renkforce

Renkforce DS100-5M Bedienungsanleitung

Image Access

Image Access WideTEK A2 Bedienungsanleitung

Fujitsu

Fujitsu FI-4860C2 Bedienungsanleitung

GeoSlam

GeoSlam ZEB Horizon Montageanleitung

Kodak

Kodak i5800 Scanner Bedienungsanleitung

Kodak

Kodak i7300 Bedienungsanleitung

Revopoint

Revopoint POP Bedienungsanleitung

Fujitsu

Fujitsu fi-4860C Bedienungsanleitung

Eddyfi Technologies

Eddyfi Technologies Floormap X Bedienungsanleitung

Faselase

Faselase F6 Bedienungsanleitung

Fujitsu

Fujitsu CardMinder Bedienungsanleitung

Uniden

Uniden BC340CRS Bedienungsanleitung

Infinite Peripherals

Infinite Peripherals INFINEA TAB M Bedienungsanleitung

Mustek

Mustek PageExpress 4800 Pro Bedienungsanleitung

Optex

Optex 750830 Bedienungsanleitung

Innova

Innova 5210 Bedienungsanleitung