Canon imageFormula DR-C225W Gebrauchsanweisung
2
Chapter 1 Introduction
Wi-Fi Connection Guide describes the setup procedure for the Wi-Fi
functions of the Canon imageFORMULA DR-C225W II (afterward called
"this scanner").
About this Product ............................................................................... 2
About Wi-Fi Connections..................................................................... 3
Trademarks............................................................................................ 5
About Open Source Licenses.............................................................. 5
Procedures and Example Screens
Wi-Fi Connection Guide describes operations using Windows 7 and OS X
10.7 (Lion) as examples. For operations that are identical between
Windows and OS X, this manual uses images from Windows as
examples.
About this Product
The Wi-Fi function in this scanner (IEEE 802.11b/g/n compatible,
2.4 GHz) supports scanning operations via wireless connection to a
computer.
By connecting this scanner to an access point in a network
environment, it can be used by any computer in the same network.
The scanner is very simple to connect if the access point supports
WPS (Wi-Fi Protected Setup).
Names of Parts
Only the Wi-Fi-related functions are covered here. See the User's Manual
for other functions.
(1) AP Switch
This switches between AP and Station modes.
The AP lamp is lit when this switch is depressed.
(2) WIRELESS Switch
Enables the Wi-Fi functions of the scanner. When enabled, the USB
functions of the scanner are disabled even with the cable connected.
The WIRELESS lamp is lit when this switch is depressed.
3
(3) WPS/RESET Button
Press to connect with a WPS-compatible access point, or to initialize
the scanner's Wi-Fi settings.
Holding this button while turning on the scanner resets it to the
factory default settings.
(4) Lamp
The following lamps indicate the scanner state.
* One of two network modes of the scanner. Change the mode depending
on the device that will be connected via Wi-Fi. For details, see "Network
modes" on p.3.
About Wi-Fi Connections
Connect the scanner to an access point or directly to a computer
according to the network environment.
Network modes
Depending on the device that will be connected to the scanner via Wi-Fi,
you can change the network mode of the scanner as follows.
The scanner should always be turned off when pressing the WIRELESS
switch to enable the Wi-Fi function.
Lamp Meaning
CONNECTION Lit (green) AP mode*: Wireless LAN working
Station mode*: connecting to the access point
Blinking
green WPS executing
Blinking red WPS Error
Blinking
orange (Station mode only) Searching for an access
point
AP Lit (green) Operating in AP mode
Unlit Operating in Station mode
STATUS Blinking
green Transferring data
WIRELESS Lit (green) Wi-Fi enabled (USB disabled)
Unlit Wi-Fi disabled (USB enabled)
Network mode Description
Station mode The scanner operates as a wireless device. In this mode, a
separate wireless access point device is necessary for the
scanner to connect to the computer.
AP mode The scanner operates without another wireless access
point. A 1-to-1 connection can be established between the
scanner and the computer.
Connecting via a wireless access point (station mode connection)
Connection to the scanner can be
made using the wireless settings of the
computer connected to the wireless
LAN access point.
See "Connecting Using the Wireless
Settings on the Computer" on p.6
If the wireless access point is WPS-
compatible, connection to the scanne‘r
can be made using the WPS feature.
See "Connecting using the WPS
function" on p.11
4
If the access point does not supports
the WPS function, make the access
point settings manually to establish
connections.
See "Connecting to a Specified Access
Point" on p.16
1-to-1 connection (AP mode connection)
Search for the scanner and connect to it
using your computer's wireless
connections feature.
See "Connecting using the AP Mode"
on p.23
Search for and connect to the scanner
from a smart device (smart phone or
tablet).
See "How to Connect Smart Devices"
on p.24
The scanner can be shared with multiple computers on the
same network via the access point, although only one can
connect to the scanner at a time.
The scanner's Wi-Fi and USB connections cannot both be
used at the same time. When connecting with Wi-Fi, the
scanner cannot be used by a computer connected via USB
cable.
When using a Wi-Fi connection, scanning is slower than with
the USB connection.
Install NetworkMonitor on the computer from which you are
using the scanner.
5
Trademarks
Canon and the Canon logo are registered trademarks of Canon Inc.
in the United States and may also be trademarks or registered
trademarks in other countries.
imageFORMULA is a trademark of CANON ELECTRONICS INC.
Microsoft, Windows, and Windows Vista are registered trademarks of
Microsoft Corporation in the United States and other countries.
OS X is a registered trademark of Apple Inc. in the United States and
other countries.
Wi-Fi, Wi-Fi Alliance, the Wi-Fi CERTIFIED logo and the Wi-Fi
Protected Setup logo are registered trademarks of the Wi-Fi Alliance.
Wi-Fi CERTIFIED, WPA, WPA2 and Wi-Fi Protected Setup are
trademarks of the Wi-Fi Alliance.
"WPS" in the settings, onscreen displays and in this manual denotes
Wi-Fi Protected Setup.
Other product and company names herein may be the trademarks of
their respective owners.
Copyright © CANON ELECTRONICS INC. 2018 ALL RIGHTS
RESERVED
About Open Source Licenses
This product includes open source software.
For details on the license conditions for each open source software,
refer to the OpenSource.txt file stored in the LICENSE folder on the
software setup disc.
6
Chapter 2 Wi-Fi Connection
The procedure for connecting to an access point using the Wireless
Connection Setup Tool in Station Mode is described here.
Connecting Using the Wireless Settings on the Computer.............. 6
Connecting using the WPS function.................................................11
Connecting to a Specified Access Point .......................................... 16
About the Computer's Wireless LAN Function................................ 21
Connecting using the AP Mode......................................................... 23
How to Connect Smart Devices......................................................... 24
Connecting Using the Wireless Settings on
the Computer
Use [Easy Setup] of the Wireless Connection Setup Tool to obtain
the necessary network information from the wireless settings of the
computer connected to the wireless LAN access point, and connect
the scanner to the same network.
If the access point is using security settings (such as MAC address
filtering), change the settings to allow connection to this scanner.
To ensure good Wi-Fi communications, perform this procedure with
the scanner initially located close to the access point.
1If the scanner is on, turn it off.
Press and hold the power button until the indicator goes out.
2Enable the wireless LAN function of the computer.
This step is not necessary if the wireless LAN function is already enabled.
See "About the Computer's Wireless LAN Function" on p.21 for wireless LAN
function setting details.
3Start the Wireless Connection Setup Tool.
This procedure describes the operation by following the on-screen
instructions of the Wireless Connection Setup Tool's Easy Setup.
Custom Setup allows arbitrary network configuration for the
scanner. For details, refer to "Chapter 3 Changing Scanner
Settings".
7
Click [Start] - [All Programs] - [Canon DR-C225] - [Wireless Connection
Setup Tool].
From the Finder, double click [Application] - [Wireless Connection Setup
Tool].
4Click [Easy Setup].
5Click [Next].
If the Wireless Connection Setup Tool is not yet installed on the
computer, see the Setup Guide to install it.
In Windows 8.1/8, it appears as shown below.
8
6Perform steps 1 to 3 as shown on the screen.
(1) Turn off the WIRELESS switch on the rear of the scanner.
(2) Connect the scanner to a computer via USB cable.
(3) Turn on the scanner.
7Click [Next].
8Select [Setup by using the computer's wireless settings], and click
[Next].
When the following message appears, click [Yes].
10
11 Click [Next].
12 Perform steps 4 and 5 as shown on the screen.
(4) Turn on the WIRELESS switch on the rear of the scanner.
(5) Turn on the scanner.
13 Click [Next].
The connection is verified.
"Wireless connection to the scanner is completed." is displayed when the
connection is verified. Setup is completed.
If the connection fails, a retry confirmation screen appears.
Click [Yes] after resetting, and proceed again from step 3.
Inhaltsverzeichnis
Andere Canon Scanner Handbücher
Canon
Canon DR-2020U - imageFORMULA - Document Scanner Bedienungsanleitung
Canon
Canon Canoscan 8800 Bedienungsanleitung
Canon
Canon CanoScan 9000F Bedienungsanleitung
Canon
Canon imageFORMULA DR-2050SP Bedienungsanleitung
Canon
Canon imageFORMULA DR-2580C Gebrauchsanweisung
Canon
Canon DR-X10C - imageFORMULA - Document Scanner Bedienungsanleitung
Canon
Canon DR-5020 Bedienungsanleitung
Canon
Canon CanoScan LiDE 20 Bedienungsanleitung
Canon
Canon DR-9050C - imageFORMULA - Document Scanner Bedienungsanleitung
Canon
Canon MS-350 Bedienungsanleitung
Canon
Canon Optura 300 Bedienungsanleitung
Canon
Canon ImageFormula R10 Bedienungsanleitung
Canon
Canon 5000F - CanoScan Scanner Bedienungsanleitung
Canon
Canon Canoscan CS8000F Bedienungsanleitung
Canon
Canon 4400F - CanoScan - Flatbed Scanner Bedienungsanleitung
Canon
Canon 3622B002 Bedienungsanleitung
Canon
Canon CanoScan LiDE 35 Bedienungsanleitung
Canon
Canon 2263B002 - imageFORMULA ScanFront 220 Bedienungsanleitung
Canon
Canon imageFormula DR-6010C Bedienungsanleitung
Canon
Canon imageFORMULA DR-S150 Bedienungsanleitung
