Carrier 53DFS250-HW Bedienungsanleitung

53DFS250-HW Thermostat

® U.S. Registered Trademark.

US Patent No. 7,114,554, 7,181,317, 7,225,054, 7,274,972, 7,636,604,

7,693,582 and other patents pending.

Installation

Guide

69-2565-05

System Types

• CoolOnly(singlestage) • HeatPump(withelectricheat)

CAUTION: ELECTRICAL HAZARD

Cancauseelectricalshockorequipmentdamage.Disconnectpowerbefore

beginninginstallation.

MERCURY NOTICE:Ifthisproductisreplacingacontrolthatcontainsmercuryin

asealedtube,donotplacetheoldcontrolinthetrash.Contactyourlocalwaste

managementauthorityforinstructionsregardingrecyclingandproperdisposal.

Must be installed by a trained, experienced technician. Readtheseinstructions

carefully.Failuretofollowtheseinstructionscandamagetheproductorcauseahazardous

condition.

Select Thermostat Location

Selectalocationforthethermostatabout5ft(1.5m)abovethefloorinanareawithgoodair

circulationataveragetemperature.

Donotinstallthethermostatwhereitcanbeaffectedby:

5 FEET

[1.5 METERS]

YES

M22258

• Draftsordeadspotsbehinddoors

andincorners.

• Hotorcoldairfromducts.

• Radiantheatfromsunor

appliances.

• Concealedpipesandchimneys.

• Unheated(uncooled)areassuch

asanoutsidewallbehindthe

thermostat.

Installation Guide

69-2565—05

Wallplate installation

Power options

For24VACprimarypower,connectcommon

sideoftransformerto“C”terminal.

24 VAC 3.0 VDC

InstalltwoAAalkalinebatteriesonthe

backofthethermostatasmarked

M32487

Drill3/16”holesfordrywall.

Drill7/32”holesforplaster.

Wire hole Mounting

screws

Wallanchors

M32488

NOT

USED

M28101

7+(50267$7

:,5(+2/(

0

:$//3/$7(

1. Separatewallplatefrom

thermostat.Grasptopandbottom

ofwallplateandpulltoremove

fromthermostat.

2. Installthewallplateasshown

below.

53DFS250-HW

369-2565—05

M32489A

NOT

USED

SCREW

INSERT WIRES

THEN TIGHTEN SCREWS

WIRE HOLE

Leavethemetaljumperwirebetween

RCandR.

Pushexcesswirebackintowallopening.

Plugwallopeningwithnon-flammable

insulation.

Terminal Designations:

R 24Voltpower

Rc Notused[1]

C 24Voltcommon

H2 2ndstageheat(electricheat)

Y Compressor

G1 Lowspeedfan

G2 Highspeedfan

O Reversingvalveforheatpumps

S1 Remotesensororremotesetback[2]

S2 Remotesensororremotesetback[2]

Wiring

Notes

[1] LeavethemetaljumperwireinplacebetweenRcandR.

[2] Sensorwiremusthaveacableseparatefromthethermostatcontrolcable.

Installation Guide

69-2565—05

Wiring

HeatPumpwithElectricHeatwiring.

Coolonlywiring.

M32495

INDOOR TEMPERATURE

SENSOR/REMOTE

SETBACK/CHANGEOVER

PIPE SENSOR

FACTORY INSTALLED JUMPER.

NOT

USED

H2 H1 W2 C O R Y Y1 G1 G2 G3

AIR SWEEP

FUNCTION

(NOT AVAILABLE)

UNIT TERMINAL BLOCK

HIGH FAN

LOW FAN

NOT USED

COMPRESSOR

24V POWER

NOT USED

COMMON

NOT USED

INDOOR TEMPERATURE

SENSOR/REMOTE

SETBACK/CHANGEOVER

PIPE SENSOR

FACTORY INSTALLED JUMPER.

JUMPER WIRE (O TO Y1) REQUIRED

WHEN HEAT PUMP INDOOR IS USED

WITH COOLING ONLY OUTDOOR UNIT.

WIRE IS FIELD SUPPLIED.

M32490A

NOT

USED

H2 H1 W2 C O R Y Y1 G1 G2 G3

AIR SWEEP

FUNCTION

(NOT AVAILABLE)

UNIT TERMINAL BLOCK

HIGH FAN

LOW FAN

COMPRESSOR

24V POWER

REVERSIBLE VALVE

COMMON

NOT USED

2ND STAGE HEAT

(ELECTRIC HEAT)

53DFS250-HW

569-2565—05

Sensor wiring for temperature averaging

WiringfourTR21(20Kohm)Sensors. WiringtwoTR21(20Kohm)Sensorsand

oneTR21-A(10Kohm)Sensortoprovidea

temperatureaveragingnetwork

WiringtwoTR21-A(10Kohm)Sensorsto

provideatemperatureaveragingnetwork.

WiringfourC7189U(10Kohm)Sensorsto

provideatemperatureaveragingnetwork.

M27481

S1 S2

T T

SUBBASE

TR21

T T

TR21

T T

TR21

T T

TR21

M27482

S1 S2

SUBBASE

TR21-A

T4 T3

TR21-A

T4 T3

THE TR21-A IS A 10K OHM SENSOR.

M27483

T4 T3

TR21-A

THE TR21-A IS A 10K OHM SENSOR.

S1 S2

SUBBASE

TR21

M27432

WIRES MUST HAVE A CABLE SEPARATE

FROM THE THERMOSTAT CABLE.

1 C7189 C7189

C7189 C7189

SUBBASE

S1 S2

Installation Guide

69-2565—05

M32497

View

Clock & More

Go Back

Done

System & Fan

FanUseEdit

Fan Auto

System Auto

Done

System & Fan

FanUseEdit

Fan Auto

System Auto

Done

M32496

Tue

Done

Go Back Done

M28102

Removetab.

Alignpinsonbackofthermostatwith

slotsinwallplate,thenpushgently

untilthermostatsnapsintoplace.

Remove tab and mount thermostat

WALL

M23024

Set date and time

Press st to

changethe

Month,Year,Date,

or Time setting.

Press DONEtosavechanges.

MonthYearDate

Press GO BACK and

NEXTtoselectthe

Month,Year,Date,

orTimefunction.

Press DONEtosaveandexit.

Installer setup

1. Press SYSTEM and FAN.2. Press and hold SYSTEM

and DONEuntilthe

displaychanges.

3. Changesettingsasrequired(seepages7-9).

Press GO BACK and NEXTtoselectthefunction.

Press sttochangethesetting.

Press DONEtosavechanges.

SettingFunction

53DFS250-HW

769-2565—05

Installer setup

Continuedonnextpage

Setup

Number Setup Name Settings & Options (factory default in bold)

0120 Date(YearUpper) 20 (2011-2078)

21 (2101-2178)

0130 Date(YearLower) 08 (2008)

 [Otheroptions:00-99]

0140 Date(Month) 6 [Otheroptions:1-12]

0150 Date(Day) 15 [Otheroptions:1-31]

0160 ScheduleOptions 4 Programmable

0 Non-programmable

0170 SystemSelection 1 Coolingonly

2 Heatpumppluselectricheat

0185 Pre-occupancyPurge

Duration

0 Noduration

 [Otheroptions:1,2,or3hours]

0220 CyclesPerHour(CPH)

forfirststagecooling/

compressor

3 Recommendedformostcompressors

 [Otheroptions:1,2,4,5or6CPH]

0270 CyclesPerHour(CPH)for

heatingfirstandsecond

stage

9 Recommended

 [Otheroptions:1–12CPH]

0280 ContinuousBacklight 0No

1 Yes

0300 Changeover 1 Auto

0 Manual

0310 Deadband 3 3°F(2.0°C)

 [Options:2–9°F(1.5–5.0°C)]

0320 TemperatureIndication

Scale

0 °F

1 °C

0330 DaylightSavingTime 1 ON

0 OFF

0340 RemoteTempSensor/

RemoteSetback/

ChangeoverInput

0None

1 Remote10KIndoor

2 Remote20KIndoor

0340

(Non-

program-

mable)

RemoteTempSensor/

RemoteSetback/

ChangeoverInput

0None

1 Remote10KIndoor

2 Remote20KIndoor

5 RemoteSetback,normallyopen

6 RemoteSetback,normallyclosed

0341 DelayforRemoteSetback 0 NoDelay

2 2MinuteDelay

0342 OverrideOption(only

availableinnon-

programmablemode)

1 Override

0 NoOverride

0343 UnoccupiedHeating

Setpoint(onlywhenremote

setbackenabled)

60 60°F(15.5°C)

 [Options:50–65°F(10–18°C)]

Installation Guide

69-2565—05

Installer setup

Continuedonnextpage

Setup

Number Setup Name Settings & Options (factory default in bold)

0346 UnoccupiedCooling

Setpoint(onlywhenremote

setbackisenabled)

80 80°F(27°C)

 [Options:75–90°F(24–32°C)]

0347 FanRamping 1 ON

0 OFF(Lo,Med,Hi)

0348 FanMode 0 UsercanchooseCycleorConstant3speed:

Low,Med,High,Auto

1 CycleOnly-Autoonly

0349 AutoFanReset 0 OFF

1 ResetbacktoAutoafter2hours

2 ResetbacktoAutoafter4hours

0535 TemporaryOccupied

DurationLimit

3 hours

 [Otheroptions:0–12hours]

0540 NumberofPeriods 44 Periods

2 2 Periods

0580 MinimumCompressorOff

Time

3 3minutes

4 4minutes

5 5minutes

0600 HeatTemperatureRange

Stops

90 90°F(32°C)

 [Options:40–90°F(4–32°C)]

0610 CoolTemperatureRange

Stops

50 50°F(10°C)

 [Options:50–99°F(10–37°C)]

0640 ClockFormat 12 12Hour

24 24Hour

0650 ExtendedFan-ontimeHeat 0 Off

90 90seconds

0660 ExtendedFan-ontimeCool 0 Off

40 40seconds

0670 KeypadLockout 0 Unlocked

1 PartialLockout1:Locksoutscheduleandsystem

changes

2 PartialLockout2:Locksoutschedule,system,

andfanchanges

3 PartialLockout3:Locksoutschedule,system,

fan,andup/downarrowchanges

4 FullyLocked:Entireinterfacelocked/non-func-

tional

0680 TemperatureControlHeat 2Standard

1 Less Aggressive

3 More Aggressive

0685 RecoveryHeatRampRate 5 5°F(2.8°C)/hour

 [Options:0–20°F(0–11°C)]

0690 TemperatureControlCool 2Standard

1 Less Aggressive

3 More Aggressive

53DFS250-HW

969-2565—05

Installer setup

Setup

Number Setup Name Settings & Options (factory default in bold)

0695 RecoveryCoolRampRate 3 3°F(1.7°C)/hour

 [Options:0–20°F(0–11°C)]

0700 TemperatureDisplayOffset 0 0°F(0.0°C)

 [Options:-3–3°F(-1.5–3°C)]

0710 RestoreFactoryDefaults 0No

1 Yes

0720 ScreenDisplay 2 DisplayBoth

0 DisplayRoomTemperature

1 DisplaySetpoint

View

Clock & More

Go Back

Done

M32498

View

Clock & More

Go Back

Done

TEST1

Duringinstallersetup,pressNEXT

repeatedlyuntil“Test”appears.

Test

number

System

status

Press NEXT to

selecttest

Press st to

changestatus

Press DONE to terminate testing.

1 Installer Test Cool 0 Off

1 CoolStage1On

2 Installer Test Fan 0 Off

1 Low

2 Med

3 High

3 Installer Test Heat 0 Off

1 HeatStage1On

2 HeatStage2On

4 Installer Test EM Heat 0 Off

1 EMHeatOn

System test System status

CAUTION: EQUIPMENT

DAMAGE HAZARD.

Compressorprotectionis

bypassedduringtesting.

Topreventequipment

damage,avoidcycling

thecompressorquickly.

Installer system test

Installation Guide

69-2565—05

Fan Sequence Operations(SetupFunction0347,0348,0349):Thethermostatcomesfactorydefault

withthefanrampingalgorithmenabled(ISU347).ThisgivestheusertheabilitytoselectAuto-Lo-

Med-HioptioninISU348orAutoonlyoptioninISU348.Autosetsthethermostatintothefanramping

algorithmmodeandautomaticallysetsthesufcientspeedforPIcontrol.Autoalsoautomatically

shutsthefanoffwhenthereisnotacallforheatingorcooling.IftheuserdecidestodisableISU347,

thenthefanwillonlyhaveLo-Med-Hioptionavailable.

IfISU347isnotenabled,thenISU348doesnotappearasauserselectionchoice.

IfISU347isenabled,thenISU349isavailableasaselectionchoice.Theusercanselecteithera2

houror4hourtimerfanresetfunction.Thefanwillresetfromaconstantspeedtoautomodeafter

thetimeperiodexpires.IfISU347isnotenabled,thenISU349doesnotappearasauserselection

choice.

Auto Changeover(SetupFunction0300):WhensettoAuto,thethermostatautomaticallyselectsheat-

ingorcoolingdependingontheindoortemperature.

Compressor Protection(SetupFunction0580):Forcesthecompressortowaitafewminutesbefore

restarting,topreventdamage.Duringthistime,themessage“Wait”ashesonthedisplay.

Special Programmable Mode Functions

InstallerSetup0160allowsthethermostattobeconguredforeitheramodewithaprogrammable7

dayscheduleorasanon-programmablethermostat.

Preoccupancy purge(ISU0185):Thisfeatureisavailableonlywhenthethermostatisconguredas

aprogrammablescheduleandwhenafanisused.Thefanwillrun1-3hoursbeforetheoccupied

schedulestartingtimetocirculateair.

Override Button, Temporary Override(DurationLimitISU0535):Whileintheprogrammablesched-

ulemode,anoverridebuttonisavailabletoperformtemporaryoverridecontrol.Thedefaultoverride

timecanbeconguredthroughISU0535.LockoutcongurationviaISU0670canproviderestrictions

onaccesstosetpointchanges,systemchanges,andschedulechanges.

No remote setback:Theremotesetbackfeatureonlyworksinthenonprogrammablemode.

Special Non-Programmable Mode Functions

Override (Optional):Theoverridefeatureisoptionalinthenon-programmablemode.Theoverride

canbeconguredthroughISU0342.Whentheoverrideisactivatedinthenon-programmablemodeit

willtemporarilyoverridetoanewsetpointuntiltheendtimeexpires.

Remote Setback:RemoteSetbackisavailable(ISU0340).Occupancysensors,manualtimeclock

inputs,andDDCnightsetbackcanbeusedtoprovideinputstosetbackthethermostat.Unoccupied

heating(ISU0343)andunoccupiedcooling(ISU0346)setpointsareavailabletocongurethesetback

setpoints.

Special functions

Andere Handbücher für 53DFS250-HW

Inhaltsverzeichnis

Andere Carrier Thermostat Handbücher

Carrier

Carrier edge Performance TP PHP01 A Series Bedienungsanleitung

Carrier

Carrier Infinity Control Home Bedienungsanleitung

Carrier

Carrier 52M Performance Series Bedienungsanleitung

Carrier

Carrier TC-WHS01 Bedienungsanleitung

Carrier

Carrier 33CS Bedienungsanleitung

Carrier

Carrier P474-1100RF Bedienungsanleitung

Carrier

Carrier 53DFST2-NP Bedienungsanleitung

Carrier

Carrier Comfort series Bedienungsanleitung

Carrier

Carrier TSTATCCPS101 Bedienungsanleitung

Carrier

Carrier 33CSSP3-FC Bedienungsanleitung

Carrier

Carrier Infinity SYSTXCCWIC01-B Bedienungsanleitung

Carrier

Carrier P/N 33CSSN2-MH Bedienungsanleitung

Carrier

Carrier 33CS420-01 Bedienungsanleitung

Carrier

Carrier TSTAT Anleitungen und Rezepte

Carrier

Carrier Cor Bedienungsanleitung

Carrier

Carrier Infinity Control Home Montageanleitung

Carrier

Carrier 33CS450-01 Bedienungsanleitung

Carrier

Carrier Comfort TC-WHS01-BLK Bedienungsanleitung

Carrier

Carrier Comfort series Bedienungsanleitung

Carrier

Carrier DEBONAIR 33CS Bedienungsanleitung

Carrier

Carrier TSTATCCPS701 Bedienungsanleitung

Carrier

Carrier Touch-n-Go TC-PHP01-A Bedienungsanleitung

Carrier

Carrier 53DFS250-HW Bedienungsanleitung

Carrier

Carrier 53DFST2-NP Bedienungsanleitung

Beliebte Thermostat Handbücher anderer Marken

EWELLY

EWELLY EW-181 Bedienungsanleitung

Prolon

Prolon T1100 Montageanleitung

Computherm

Computherm Q20 Bedienungsanleitung

Heatmiser

Heatmiser neoStat Bedienungsanleitung

Mars

Mars HEAT CONTROLLER IR Wireless Thermostat Bedienungsanleitung

Saswell

Saswell SAS920XWHB-7-S-RF Leitfaden

Aircalo

Aircalo TFP1-ET85P2 Bedienungsanleitung

Honeywell

Honeywell CM721 Bedienungsanleitung

Lennox

Lennox iHarmony Zone Thermostat Montageanleitung

Gemtech

Gemtech GT7000 Bedienungsanleitung

Rollei

Rollei Smartes 45000 Bedienungsanleitung

Sinope

Sinope TH1300RF Bedienungsanleitung

Honeywell

Honeywell RLV4305 Bedienungsanleitung

Honeywell

Honeywell Prestige 2.0 THX9421 Bedienungsanleitung

NuTone

NuTone NTBZ48 Original Betriebsanleitung

Stelpro

Stelpro MAESTRO ASMT402AD Bedienungsanleitung

Honeywell

Honeywell T6811 Bedienungsanleitung

Aube Technologies

Aube Technologies TH305 Bedienungsanleitung