Carrier A07049 Bedienungsanleitung

Turn to the Expert_

Installation Instructions

ii_i_i!i! i_i_i_;;;;,,i_i_/i

i_i:iiiiii _i!_i!_iJ!_!ili:!i:ii:ii:ii:ii:ii:iii!:iii_ iiiii_ii:ii{iiiii:¸¸¸_¸¸¸;¸_¸¸¸¸¸;¸;;¸¸<¸¸¸';;>:_¸¸¸>i_;;¸¸¸;¸¸¸¸_........... !!i_!

A07049

Programmable Control

(€

A07048

Non-Programmable Control

Designed and Assembled in the U.S.A.

NOTE: Read the entire instruction manual before starting the installation.

US patents: US7287709 B2, US20080147242 A 1, USD582800 S[, US20060165149 A 1, US6956463 B2.

TABLE OF CONTENTS

PAGE

SAFETY CONSIDERATIONS .................................... 1

INTRODUCTION .............................................. 2

INSTALLATION CONSIDERATIONS .............................. 3

INSTALLATION ............................................... 6

SYSTEM START-UP AND CHECKOUT .......................... 38

OPERATIONAL INFORMATION ................................ 41

TROUBLESHOOTING ......................................... 45

WIRING DIAGRAMS .......................................... 49

THERMOSTAT CONFIGURATION RECORD ...................... 58

SAFETY CONSIDERATIONS

Read and follow manufacturer instructions careflflly. Follow all local electrical

codes during installation. All wiring must conform to local and national electrical

codes. Improper wiring or installation may damage AC/HP Control.

Recognize safety information. This is the safety-alert symbol /_ . When you see

this symbol on the equipment and in the instruction manual, be alert to the

potential for personal injury.

Understand the signal words DANGER, WARNING, and CAUTION. These

words are used with the safety-alert symbol. DANGER identifies the most

serious hazards which will result in severe personal injury or death. WARNING

signifies a hazard which could result in personal injury or death. CAUTION is

used to identify unsafe practices which may result in minor personal injury or

product and property damage. NOTE is used to highlight suggestions which will

result in enhanced installation, reliability, or operation.

INTRODUCTION

Carrier's 7-day, 5/2-day, l-day programmable and non-programmable

Performance Series Thermostat Control is a wall-mounted, low-voltage

temperature control in either a single unit or a two-piece unit. In two-piece

configuration, the relays are located near the equipment and a two-wire

connection is used between the Display Module and the Equipment Control

Module. Single-piece installation requires more wiring and results in a higher

profile. The Edge 'M Thermostat has no need for batteries to store

user-configured settings in memory. During power loss its internal memory

saves settings for unlimited time, and the clock continues to run for at least 24

hours. An extension of Carrier's proven line of thermostats; it provides separate

setpoints for heating and cooling.

In the Edge Thermostat Control programmable configuration, different heating

and cooling setpoints and times are programmable for 4 periods per day or 2

periods per day. Programming can be done for 7 days per week, 5/2 days per

week, or 1 day. The programmable Thermostat Control can also be user

configured as a non-programmable Thermostat Control.

The non-programmable Thermostat Control features Touch 'N' Go 'Msettings

for quick and easy temperature change without complicated programming

schedules. And, its Touch 'N' Go technology enables the user to switch between

three different user-configurable settings through intuitive buttons located just

below the display.

INSTALLATION CONSIDERATIONS

Power

This control is powered by 24VAC only. It requires 24VAC (Rh and/or Rc and C

terminals) of the low-voltage transformer to be connected to it for proper

operation. It will not operate without these 2 connections. Rh and Rc are

connected via PCB breakout jumper. See Fig. 1. For applications using two

24VAC transformers, one in the indoor unit and one in the outdoor unit, connect

the common from each to the C terminal. Connect R from the indoor unit to the

Rh terminal. Connect R from the outdoor unit to the Rc terminal. Then, break

jumper on the circuit board. The W signal is taken from the Rh power and the G

signal is taken from the Rc power. If the thermostat has been installed in a

two-transformer application that is later changed to a single-transformer

installation, installer must install a field supplied jumper between Rc and Rh.

Depending on the installation, up to 14 wires may be required. Installation as

two-piece unit is recommended. Only 2 wires are required for connection

between Display Module and Equipment Control Module. These two wires (V+

and Vg) do not provide ordinary 24VAC. They carry a combination of power

and communications data that is unique to these products.

Fig. 1 - PCB Breakout Jumper

A07052

Models

There are programmable and non-programmable models for all applications.

They can be configured for AC or HP installations, allowing it to be used in

place of all Carrier thermostats. Programmable thermostats may be configured as

non-programmable if user desires.

Outdoor Temperature Sensor

The outdoor air temperature sensor is not included with the AC/HP Control. It is

available as an accessory, part number TSTATCCSEN01-B. Optimum

performance is obtained when an outdoor temperature sensor is used with the

AC/HP Control. Plan installation so that 2 wires can be run from Equipment

Control Module to an outdoor location, preferably on the north side of the house

or refer to Installation Instructions included with the outdoor temperature sensor

for simplified connection. Sensor can be mounted to outdoor unit and existing

dedicatedsensorwiresmaybeusedforitsconnection.Detailsareprovidedin

sensorinstructions.

RemoteIndoorTemperatureSensor

Aremotetemperaturesensormaybeusedwiththeprogrammableheatpump

andprogrammableairconditionerthermostatswhereitisdesirabletoinstallthe

thermostatinalimitedaccesslocationwhilemeasuringthetemperatureinthe

livingspace.Theremoteroomsensormaybeusedasastandaloneoraverage

withlocalsensor.

Two-PieceThermostatConfiguration

The Performance Series AC/HP Control can be installed in one of two

configurations. The control may be installed as a single-piece thermostat or it

may be split into two pieces and mounted in separate locations. As a single-piece

unit, all required wiring must be brought to the Equipment Control Module for

connection to the terminal strip. In two-piece configuration, the Display Module

can be mounted in the living space while the Equipment Control Module may be

mounted near the indoor furnace or fan coil. Connection from the display to the

Equipment Control Module requires only two wires. All other control wires are

connected to the Equipment Control Module from the HVAC equipment. This

configuration results in a slimmer display and locates the Equipment Control

Module containing the switching relays away from the main living space where

relay clicking will not be heard.

The model numbers on the Display Module and the Equipment Control Module

(ECM) must match or unpredictable results may occur.

Two-wire pigtail replacement part number is TX-2WR-05.

Wiring

Wirelengthshouldbenomorethan250ft(76m).Use22AWGfornormal

wiringapplications.Continuouswirelengthsover100ft(30.5m)shoulduse20

AWGorlarger. INSTALLATION

Cartoncontainsthefollowingcomponents.SeeFig.2forprogrammablemodels

orFig.3fornon-programmablemodels.

A07754

Fig. 2- TP-PAC /TP-PHP Carton Contents

1. Display Module

2. Stand-off for Equipment Control Module

3. Screws and pig tail

4. Equipment Control Module

A07755

Fig. 3-TP-NAC /TP-NHP Carton Contents

1. Display Module

2. Stand-off for Equipment Control Module

3. Screws and pig tail

4. Equipment Control Module

AC/HP Control Location

AC/HP Control should be mounted:

• Approximately 5 ft (1.5m) from floor.

• Close to or in a frequently used room, preferably on an inside parti-

tioning wall.

• On a section of wall without pipes or duct work.

AC/HPControlshouldNOTbemounted:

• Closetoawindow,onanoutsidewall,ornexttoadoorleadingtothe

outside.

• Exposedtodirectlightorheatfromalamp,sun,fireplace,orother

temperature-radiatingobjectswhichcouldcauseafalsereading.

• Closetoorindirectairflowfromsupplyregistersandreturn-airregis-

ters.

• Inareaswithpooraircirculation,suchasbehindadoororinanal-

cove.

Installershoulddeterminewhethercontrolwillbeinstalledassingle-pieceor

two-piece.Insingle-piececonfiguration,asmanyas14wiresmayneedtorun

to wallmountinglocationforconnectionto thecontrol.In two-piece

configuration,theDisplayModuleandEquipmentControlModuleare

connectedbytwowires.

Install AC/HP Control

ELECTRICAL OPERATION HAZARD

Failure to follow this warning could result in personal injury or

death.

Before installing AC/HP Control, turn off all power to

equipment. There may be more than 1 power disconnect.

UNITDAMAGE HAZARD

Failure to follow this caution may result in equipment damage

or improper operation.

Improper wiring or installation may damage AC/HP Control.

Check to make sure wiring is correct before proceeding with

installation or turning on power.

1. Turn off all power to equipment.

2. If an existing thermostat is being replaced

a. Remove existing thermostat from wall.

b. Disconnect wires from existing thermostat, 1 at a time.

c. As each wire is disconnected, record wire color and terminal marking.

d. Discard or recycle old thermostat.

ENVIRONMENTAL HAZARD

Failure to follow this caution may result in environmental

damage.

Mercury is a hazardous waste. Federal regulations require that

Mercury be disposed of properly.

Andere Handbücher für A07049

Dieses Handbuch passt für folgende Modelle

Andere Carrier Thermostat Handbücher

Carrier

Carrier ComfortVu TB-24 Betriebsanleitung

Carrier

Carrier AQUAZONE 50QE900-250FS Bedienungsanleitung

Carrier

Carrier Performance TP-PAC Bedienungsanleitung

Carrier

Carrier EDGE PRO 33CS2PP2S-01 Bedienungsanleitung

Carrier

Carrier Comfort Touch-n-Go Bedienungsanleitung

Carrier

Carrier 33CS Bedienungsanleitung

Carrier

Carrier Comfort Pro 33CSCNACHP-01 Bedienungsanleitung

Carrier

Carrier ComfortVu TB-24-HM Betriebsanleitung

Carrier

Carrier 33AW-CS1 Bedienungsanleitung

Carrier

Carrier 53DFS250-HW Bedienungsanleitung

Carrier

Carrier EDGE PRO 33CS2PPRH-01 Bedienungsanleitung

Carrier

Carrier ComfortVu TBPL-24-H Betriebsanleitung

Carrier

Carrier MODULINE 37HS Datenblatt

Carrier

Carrier Cor Bedienungsanleitung

Carrier

Carrier TSTATCCPS701 Bedienungsanleitung

Carrier

Carrier TSTAT Bedienungsanleitung

Carrier

Carrier 33CS Bedienungsanleitung

Carrier

Carrier Connect 33CONNECTSTAT43FX Bedienungsanleitung

Carrier

Carrier NSA-A/CP-I-2.5-4X Betriebsanleitung

Carrier

Carrier Infinity SYSTXCCITC01-C Bedienungsanleitung

Carrier

Carrier Totaline Star P474-1010 Bedienungsanleitung

Carrier

Carrier 33CS Bedienungsanleitung

Carrier

Carrier KSACN0901AAA Bedienungsanleitung

Carrier

Carrier NON-PROGRAMMABLE DIGITALTHERMOSTAT Bedienungsanleitung

Beliebte Thermostat Handbücher anderer Marken

EWELLY

EWELLY EW-181 Bedienungsanleitung

Prolon

Prolon T1100 Montageanleitung

Computherm

Computherm Q20 Bedienungsanleitung

Heatmiser

Heatmiser neoStat Bedienungsanleitung

Aube Technologies

Aube Technologies TH111GFCI-NP 240 VCA Bedienungsanleitung

Mars

Mars HEAT CONTROLLER IR Wireless Thermostat Bedienungsanleitung

Saswell

Saswell SAS920XWHB-7-S-RF Leitfaden

Aircalo

Aircalo TFP1-ET85P2 Bedienungsanleitung

Honeywell

Honeywell CM721 Bedienungsanleitung

Lennox

Lennox iHarmony Zone Thermostat Montageanleitung

Gemtech

Gemtech GT7000 Bedienungsanleitung

Rollei

Rollei Smartes 45000 Bedienungsanleitung

Sinope

Sinope TH1300RF Bedienungsanleitung

Honeywell

Honeywell RLV4305 Bedienungsanleitung

Honeywell

Honeywell Prestige 2.0 THX9421 Bedienungsanleitung

NuTone

NuTone NTBZ48 Original Betriebsanleitung

Stelpro

Stelpro MAESTRO ASMT402AD Bedienungsanleitung

Honeywell

Honeywell T6811 Bedienungsanleitung