CAS PD-II Bedienungsanleitung

Andere Handbücher für PD-II

5

Inhaltsverzeichnis

Andere CAS Skala Handbücher

CAS

CAS DL Series Bedienungsanleitung

CAS

CAS PR-C series Bedienungsanleitung

CAS

CAS CL8000 Series Bedienungsanleitung

CAS

CAS LP-1000N Series Bedienungsanleitung

CAS

CAS CL5200J Series Bedienungsanleitung

CAS

CAS CL7200 series Bedienungsanleitung

CAS

CAS SW-1S Series Bedienungsanleitung

CAS

CAS ER Series Bedienungsanleitung

CAS

CAS PB Series Bedienungsanleitung

CAS

CAS PD-II Bedienungsanleitung

CAS

CAS GBF-1039 Bedienungsanleitung

CAS

CAS SW-1S Series Bedienungsanleitung

CAS

CAS PB Series Bedienungsanleitung

CAS

CAS CUW Series Bedienungsanleitung

CAS

CAS ED Series Bedienungsanleitung

CAS

CAS LP-II Montage- und Wartungsanleitung

CAS

CAS DB-II Bedienungsanleitung

CAS

CAS SW-2 Bedienungsanleitung

CAS

CAS DB-1H Bedienungsanleitung

CAS

CAS PR-T Series Bedienungsanleitung

CAS

CAS AP Plus-MX Bedienungsanleitung

CAS

CAS PW-II Bedienungsanleitung

CAS

CAS CL-3000 Series Bedienungsanleitung

CAS

CAS BF-1255 Bedienungsanleitung

Beliebte Skala Handbücher anderer Marken

AWS

AWS ZEO-50 Bedienungsanleitung

Gima

Gima Glass Body Fat Analyzer Stücklistenhandbuch

Seca

Seca 374 Bedienungsanleitung

TEC

TEC TEC SL59 SERIES Bedienungsanleitung

Axis

Axis B/E Series Bedienungsanleitung

Alecto

Alecto ACW-40 Bedienungsanleitung

Rice Lake

Rice Lake MSI-4260 IS Bedienungsanleitung

IKA

IKA RCT basic safety control Bedienungsanleitung

ADE

ADE M20011 Bedienungsanleitung

Duronic

Duronic KS3000 Bedienungsanleitung

Digi

Digi SM-720 Bedienungsanleitung

Cardinal

Cardinal CS Series Bedienungsanleitung

Korona

Korona Kastella Bedienungsanleitung

A&D

A&D FC-50Ki Bedienungsanleitung

BDA

BDA CAMARGUE Bedienungsanleitung

Tanita

Tanita HD-357 Bedienungsanleitung

Leifheit

Leifheit 03173 Bedienungsanleitung

Lumme

Lumme LU-1340 Bedienungsanleitung

09/10/09CAS (USA) Corporation 99 Murray Hill Parkway East Rutherford, NJ 07073 PD-II

PROGRAMMING LBS/OZ FOR PD-II CAL MODE OPTIONS

1. Make sure that the scale is off. Remove the platter. Remove the calibration bolts and plate

located on the top front of the scale.

2. After removing the calibration bolts and plate you will see a white micro switch at the bottom of

the hole. Press and hold down the micro switch and turn on the scale.

3. The display will read “CAL” → “Ver XXX “→ “C-0 “. Release the micro-switch. Press the [ # ]

key until the display shows “C-4 “. Replace the platter. ( “ # “ is to increase and “lb/oz“is to

decrease the value )

4. Press the [ ZERO ] key and display should read “C41 XX “. Press [ ZERO ] to go to the next

step “ C42 XX “ → “ C43 XX “ → “C44 XX “ → “ C45 XX “ → “ C46 XX “.

5. Depending on the capacity and function, enter the value “XX “step by step. Press “# “to move

the digit and “* or lb/oz “to change the value. ( see chart below)

6. Note: For the setting “C42” for all capacities single range is “38” and dual range is what is in the

chart below.

7. The settings for the capacity and single/dual range must follow what is on the serial number plate

or else the scale will not be NTEP or legal for trade subject to a fine by Weights and Measures.

15lb/300oz

30lb/600oz

60lb/1000oz

150lb/2000oz

C41

C8

C8

C8

C8

C42

1A

3A

4A

62

C43

00

00

00

00

C44

80

80

80

80

C45

00

00

00

00

C46

00

00

00

00

8. Press the [ ZERO ] key. Display shows “C4 End “then “C-4 “.

9. Press “* or lb/oz “until the display shows “C-0 “.

C41

C44

What the scale does

C8

80

Starts up in lb and can be switched to oz

d0

80

Starts up in oz and can be switched to lb

C8

00

Starts up in lb and will not switch to oz

D0

00

Starts up in oz and will not switch to lb

10. Press the [ ZERO ] key and scale will do its count up test cycle and the go to “0 “which is

back to normal mode

* Make sure to calibrate the scale in lbs or kg before using.

CHANGING TYPE SETTINGS

1. Make sure that power is OFF. While pressing “# “key, then turn on the power. Display will show

“EcrSEt “. Then current ECR type is shown on the display as “tYPE-2 “.

2. If you select ERC type 5, press the “# “key until the display shows it.

3. To save the current type, press the ZERO Key. Display will go back to “0 “.