Centurion D2 Turbo Bedienungsanleitung
DOMESTIC
SLIDING GATE
OPERATOR
FOR 250KG GATES
D2 Turbo and D2 Turbo Low-Voltage
Installation Manual
e
g
a
t
l
o
V
-
w
o
L
Company Profile
Centurion Systems (Pty) Ltd reserves the right to make changes to the products described in this manual without notice
and without obligation of Centurion Systems (Pty) Ltd to notify any persons of any such revisions or changes.
Additionally, Centurion Systems (Pty) Ltd makes no representations or warranties with respect to this manual.
No part of this document may be copied, stored in a retrieval system or transmitted in any form or by any means electronic,
mechanical, optical or photographic, without the express prior written consent of Centurion Systems (Pty) Ltd.
Sales and technical support
to over 50 countries
worldwide
1986 1990 1995 1999 Centurion Systems (Pty) Ltd
Today
100%
testing of
products
In-house
R & D
development
team
Manufacture to
international
quality standard
ISO 9001:2008
After-sales
technical support
from 07h00 - 18h00
Monday to Friday
Contents
Mechanical Setup
Electrical Setup
Commissioning and Handover
IMPORTANT SAFETY FEATURES
1. Declaration of Conformity
2. General Description
3. Specifications
Physical Dimensions
Technical Specifications
4. Product Identification
5. Required Tools and Equipment
6. Glossary
7. Preparation of Site
8. Cabling Requirements
9. Lubrication
10. Operator Installation
Foundation plate installation
Cast foundation plate into concrete
Bolt foundation plate onto an existing concrete plinth
Retrofitting to an existing D3 foundation plate
11. Electrical Setup
12. Wiring Diagram for Closing Safety Beams
13. Wiring Diagram for Opening Safety Beams
14. Wiring Diagrams for External Radio Receiver
15. Wiring Diagrams for Other Inputs
16. Wiring Diagram for Pillar Light to the D2 Turbo Controller
17. Wiring Diagram for Pillar Light to the D2 Turbo Low-Voltage
Controller
18. Mains Supply and Battery Connections
19. Earthing for Effective Lightning Protections
20. Commissioning the System
Setting up the gate Limits
21. Features and Functions
22. Customising the Features and Functions
page 1
page 2
page 2
page 3
page 6
page 7
page 8
page 8
page 8
page 10
page 11
page 12
page 13
page 17
page 18
page 19
page 21
page 21
page 23
page 25
page 38
page 39
page 40
page 41
page 42
page 43
page 44
page 45
page 46
page 47
page 47
page 49
page 60
page 77
page 79
page 80
page 84
page 85
page 86
page 87
page 88
23. Description of Terminal Functions
24. Diagnostics
25. Troubleshooting
26. Manual Operation
27. Additional Features
28. Basic Maintenance
29. Servicing the Operator
30. Installation Handover
Mechanical Setup
Required tools and equipment page 11
Site considerations page 12
Cabling requirements page 15
Lubrication page 17
Operator installation page 17
Foundation plate installation page 19
Route cables page 26
Mount gearbox page 27
Mount the rack page 29
These abbreviated instructions are for the experienced
installer who needs a checklist to get a standard installation
up and running in the minimum of time.
Detailed installation features and functions are referred to
later in this manual.
page 1
Connect all wiring
page 48
page 87
page 90
step
10
Electrical Setup
step
1
1
Set the gate limits
step
13
Carry out professional
handover to client
Commissioning
and Handover
step
1
2
Set additional features
page 38-45
page 2
Warnings for the Installer
CAREFULLY READ AND FOLLOW ALL INSTRUCTIONS before
beginning to install the product.
All installation, repair, and service work to this product must be done
by a suitably qualified person
Do not activate your gate opener unless you can see it and can
determine that its area of travel is clear of people, pets, or other
obstructions
NO ONE MAY CROSS THE PATH OF A MOVING GATE. Always keep
people and objects away from the gate and its area of travel
NEVER LET CHILDREN OPERATE OR PLAY WITH THE GATE
CONTROLS, and do not allow children or pets near the gate area
Secure all easily-accessed gate opener controls in order to prevent
unauthorised operation of the gate
Do not in any way modify the components of the automated system
Do not install the equipment in an explosive atmosphere: the
presence of flammable gas or fumes is a serious danger to safety
Before attempting any work on the system, isolate electrical power
and disconnect the batteries
The mains power supply of the automated system must be fitted with
an all-pole switch with contact opening distance of 3mm or greater.
The use of a 5A thermal breaker with all-pole circuit break is
recommended
Make sure that an earth leakage circuit breaker with a threshold of
30mA is fitted upstream of the system
Never short-circuit the battery and do not try to recharge the
batteries with power supply units other than that supplied with the
product, or supplied by Centurion Systems
Make sure that the earthing system is correctly constructed, and that
all metal parts of the system are suitably earthed
IMPORTANT
Safety Instructions
ATTENTION
To ensure the safety of people, it is important that
you read all the following instructions.
Incorrect installation or incorrect use of the product could
cause serious harm to people.
The installer, being either professional or DIY, is the last
person on the site who can ensure that the operator is safely
installed, and that the whole system can be operated safely.
page 3
1
2
page 4
Safety devices such as gate safety infrared beams must be fitted to
the installation to guard against mechanical movement risks such as
crushing, dragging and shearing
It is recommended that at least one warning indicator light be fitted
to every system
Always fit the warning signs visibly to the inside and outside of the
gate
The installer must explain and demonstrate the manual override
operation of the gate in case of an emergency, and must hand the
User Guides and Safety/Warning documents over to the end-user
Explain these safety instructions to all persons authorised to use this
gate, and be sure that they understand the hazards associated with
automated gates
Do not leave packing materials (plastic, polystyrene, etc.) within
reach of children as such materials are potential sources of danger
Dispose of all waste products like packaging materials, worn-out
batteries, etc, according to local regulations.
Always check the obstruction detection system, and/or safety devices
for correct operation prior to handover. During the handover of the
system, explain to the end-user how to perform these checks to
confirm that all safety devices are operating correctly
Centurion Systems does not accept any liability caused by improper
use of the product, or for use other than that for which the
automated system was intended
This product was designed and built strictly for the use indicated in
the documentation provided with the product. Any other use, not
expressly indicated within the documentation, could be a source of
danger and/or compromise the service life/operation of the product
Everything not expressly specified in these instructions is not
permitted.
MOVING GATE
CAN CAUSE
INJURY
www.centsys.com
KEEP CLEAR. GATE MAY MOVE
AT ANY TIME. DO NOT ALLOW
CHILDREN TO PLAY IN AREA OR
OPERATE GATE
page 5
Icons used in this Manual
This icon indicates tips and other information that could be
useful during the installation.
This icon indicates warning, caution or attention! Please
take special note of critical aspects that MUST be
adhered to in order to prevent injury.
This icon denotes variations and other aspects that should be
considered during installation.
Before you attempt to use your new gate motor for the first time, you
should know:
At no point must 220V be supplied to the system! This is a
low-voltage model and connecting a voltage supply that
exceeds its maximum specifications will irreparably damage
the electronics
No earth terminal is provided for the incoming power, and is
not necessary, but the earthing lead must still be grounded to
the motor base plate as this serves as lightning protection
The diameter of the cable needed to supply power to the
system will depend on the distance between the transformer
and the motor, as well as on the output voltage of the
transformer used. The table below shows the typical cable
thicknesses for corresponding distance and assumes a 16V AC
transformer output
Distance from the transformer
to the motor
Up to 20m
20m - 40m
40m - 60m
Minimum cable
thickness required
1mm²
1.5mm²
2.5mm²
TABLE 1.
IMPORTANT Site Considerations
for the D2 Turbo Low-Voltage
page 6
Manufacturer
Centurion Systems (Pty) Ltd
Unit 13 Production Park
Intersection Newmarket Road & Epsom Avenue
North Riding
Gauteng
South Africa
Declares that the product
Product name: D2 Turbo/D2 Turbo Low-Voltage Sliding gate operator
Conforms with the following specifications
Safety: SANS 60335-1:2007
IEC 60335-1:2006
Emissions: CISPR 11 CLASS A - Radiated and conducted Interference field
strength (emission tests) – 150KHz TO 6GHz
Immunity: IEC 61000-4-2 – Electrostatic discharge
IEC 61000-4-3 – Radiated immunity – 80MHz TO 1000MHz
IEC 61000-4-4 – Electrical fast transients/burst
IEC 61000-4-5 – Surges
IEC 61000-4-6 – Conducted immunity – 150KHz TO 80MHz
IEC 61000-4-11– Voltage dips and interruption
Standard to which conformity is declared
IEC 60335-1:2006 Safety
IEC 61000-6-4:2006 Emissions
IEC 61000-6-2:2005 Immunity
Signed at North Riding, South Africa on April 14, 2010
Ian Rozowsky
Research & Development Director
1. Declaration of Conformity
Andere Handbücher für D2 Turbo
6
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere Centurion Toröffner Handbücher
Centurion
Centurion D10 Bedienungsanleitung
Centurion
Centurion R3 Bedienungsanleitung
Centurion
Centurion D5-EVO REPAIR Betriebsanleitung
Centurion
Centurion VECTOR2 Bedienungsanleitung
Centurion
Centurion VECTOR2 Bedienungsanleitung
Centurion
Centurion CP70R5 Bedienungsanleitung
Centurion
Centurion D3 Bedienungsanleitung
Centurion
Centurion D3 Bedienungsanleitung
Centurion
Centurion Auto-Mate Bedienungsanleitung
Centurion
Centurion R3 Bedienungsanleitung
Centurion
Centurion A10 Series Bedienungsanleitung
Centurion
Centurion VECTOR2 Bedienungsanleitung
Centurion
Centurion Vector Bedienungsanleitung
Centurion
Centurion D5-EVO REPAIR Bedienungsanleitung
Centurion
Centurion R3 Bedienungsanleitung
Centurion
Centurion A10 Series Betriebsanleitung
Centurion
Centurion D10 Bedienungsanleitung
Centurion
Centurion R3R5 Bedienungsanleitung
Centurion
Centurion D5-EVO REPAIR Bedienungsanleitung
Centurion
Centurion D3 Bedienungsanleitung
