Chamberlain The Protector G70 Bedienungsanleitung

Chamberlain

Built for Good

INSTRUCTIONS

“THE PROTECTOR” SYSTEM

MODEL G70 OBSTRUCTION SENSOR

“The Protector” is the latest addition to the safety features already built into the Chamberlain line of garage

door openers. An invisible light beam passes between the detector and emitter. A signal will be transmitted to

the opener if an obstruction breaks the beam. Upon receiving this signal, the opener will respond by causing a

closing door to open or by preventing an open door from closing. “The Protector has no effect on a door

that is closed or is opening.

Install the Protector after the garage door opener installation has been completed.

THIS SAFETY ALERT SYMBOL MEANS CAUTION PERSONAL SAFETY OR

PROPERTY DAMAGE INSTRUCTION. READ THESE INSTRUCTIONS

CAREFULLY.”

THE PROTECTOR MUST BE INSTALLED AND OPERATED IN STRICT

ACCORDANCE WITH THE FOLLOWING INSTRUCTIONS MAY RESULT IN

PERSONAL INJURY OR PROPERTY DAMAGE.

BEFORE INSTALLING THE PROTECTOR, BE SURE TO COMPLY WITH ALL GARAGE

DOOR OPENER INSTALLATION AND ADJUSTMENT REQUIREMENTS AS PROVIDED IN

YOUR OWNERS MANUAL.

DISCONNECT POWER TO GARAGE DOOR OPENER BEFORE INSTALLING THE

PROTECTOR

TO PROTECT SMALL CHILDREN, INSTALL THE PROTECTOR NO HIGHER THAN 4 TO 6

INCHES ABOVE GARAGE FLOOR

FASTEN HANDY HINTS TO WALL AT EYE LEVEL ABOVE ONE OF THE BRACKETS.

DISCONNECT POWER TO GARAGE DOOR OPENER

BEFORE INSTALLING THE PROTECTOR.

(Figure 2.) The Protector must be installed so the path of the light beam is not

obstructed by the garage door, door tracks, springs, hinges, rollers or any other part

of the door mechanism. It may be necessary to add a piece of wood to the wall at

mounting locations to insure proper clearance (or to install sensors on masonry

wall construction).

TO PROTECT SMALL CHILDREN INSTALL PROTECTOR NO

HIGHER THAN 4 TO 6 INCHES ABOVE FLOOR

STEP 1

PROCEDURE: (Figures 1 & 2). Install emitter and detector inside garage on each

side of garage door. Sensors must be positioned at the same height

(approximately 4” to 6” above the floor). Directional arrows on the sensor labels

must point toward each other and be horizontal to the floor.

NOTE: Detector should be installed on the “shade” side of the garage, away from

the sun’s direct rays.

(Figure 2). Drill 3/16” pilot holes. Fasten brackets to walls with 1/4”x1-1/4” lag

screws.

NOTE: Slotted holes in bracket allow for positioning. Be sure label

arrows are horizontal with the floor before tightening screws

Run the yellow/yellow-green striped wires attached to the detector up and over the

door to the terminals on the emitter. Attach wires to emitter terminals by color as

shown on the label. Use insulated staples to fasten wires to walls surrounding

garage door.

STEP 2

(Figure 3). Run the black/white 2-conductor wires attached to the detector

up the wall and across the ceiling to opener terminals. Connect wires to

terminals by color as shown on the label.

NOTE: If your opener is equipped with a Lock Switch, be sure it is

OFF before proceeding to Step 3.

STEP 3

(Figure 4). Plug in the garage door opener to restore electric power.

Small red lamp in detector should GLOW.

If red lamp FLASHES after installation, check bracket position (see Step

1). Arrows should be horizontal to the floor. If brackets are installed

correctly, position of detector within mounting bracket may require

adjustment. Loosen detector case mounting screw and rotate detector. If

red lamp GLOWS, retighten mounting screw. Alignment is correct. If light

continues flashing after adjustment, check for:

1. Dirt on the detector lens or sunlight shining directly into the lens,

causing interference.

2. Shorts in yellow/yellow-green striped wires. These can occur under

staples or at screw terminals.

3. Incorrect wiring of detector to emitter.

If no light glows in the detector lamp after installation, check for:

1. Electric power to the opener.

2. Shorts in the black/white wires. These can occur under staples or at

screw terminal connections.

3. Incorrect wiring between detector and opener.

STEP 4

TEST THE PROTECTOR OBSTRUCTION SENSOR:

Place an obstacle in the path of the invisible light beam between detector

and emitter as the garage door is closing. The door must reverse and

return to full open position. NOTE: The garage door opener will not

respond to a CLOSE command if the red light in the detector is

flashing.

The garage door opener can be closed manually by pulling down on the

emergency release rope and handle connected to the trolley. (See the

Protector Handy Hints Label).

FASTEN THE HANDY HINTS TO WALL AT EYE LEVEL

ABOVE A SENSOR.

CHAMBERLAIN SERVICE IS ON CALL

OUR LARGE SERVICE ORGANIZATION SPANS AMERICA.

INSTALLATION AND SERVICE INFORMATION IS AS NEAR AS YOUR TELEPHONE SIX DAYS A WEEK.

SIMPLY DIAL OUR TOLL FREE NUMBER: 1-800-528-9131

HOURS: 7:00 a.m. to 3:30 p.m. (Mountain Std. Time)

MONDAY through Saturday

For professional installation, parts, and service; contact your local CHAMBERLAIN/LIFTMASTER dealer. Look for him in

the Yellow Pages or call our Toll Free number for a list of dealers in your area.

114A801

Inhaltsverzeichnis

Andere Chamberlain Zubehör Handbücher

Chamberlain

Chamberlain PIRV400R Bedienungsanleitung

Chamberlain

Chamberlain THE PROTECTOR SYSTEM 916GA Bedienungsanleitung

Chamberlain

Chamberlain 915GA Bedienungsanleitung

Chamberlain

Chamberlain 771E Bedienungsanleitung

Chamberlain

Chamberlain 836LM Bedienungsanleitung

Chamberlain

Chamberlain 50-HERK2 Bedienungsanleitung

Chamberlain

Chamberlain 821LM-SENSOR Bedienungsanleitung

Chamberlain

Chamberlain Secure Home SH-9525AU Bedienungsanleitung

Chamberlain

Chamberlain SWG-0500 Bedienungsanleitung

Chamberlain

Chamberlain 41C4672 Leitfaden

Chamberlain

Chamberlain Protector System 770EML Bedienungsanleitung

Chamberlain

Chamberlain 771ANZ Bedienungsanleitung

Chamberlain

Chamberlain CPS-UN4 Bedienungsanleitung

Chamberlain

Chamberlain LMTBU Bedienungsanleitung

Chamberlain

Chamberlain PROFESSIONAL TCLS1E Bedienungsanleitung

Chamberlain

Chamberlain DH Kurzanleitung

Chamberlain

Chamberlain Protector 87LM Bedienungsanleitung

Chamberlain

Chamberlain DH Montage- und Bedienungsanleitung

Chamberlain

Chamberlain 870CB Series Bedienungsanleitung

Chamberlain

Chamberlain Protector System 770E Bedienungsanleitung

Chamberlain

Chamberlain LMTBUL Bedienungsanleitung

Chamberlain

Chamberlain 916GA Bedienungsanleitung

Chamberlain

Chamberlain PIR2300R Bedienungsanleitung

Chamberlain

Chamberlain LMRRU Bedienungsanleitung

Beliebte Zubehör Handbücher anderer Marken

Hillco

Hillco 2810 Bedienungsanleitung

Siemens

Siemens QSA2700D Bedienerhandbuch

Contours

Contours ZY024 Bedienungsanleitung

Saivod

Saivod VS621 Bedienungsanleitung

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Bedienungsanleitung

Z-Wave

Z-Wave HSD-200Z Bedienungsanleitung

turck

turck FMX-IM-2UPLI63FX Bedienungsanleitung

Decagon Devices

Decagon Devices 10HS Bedienungsanleitung

UPPAbaby

UPPAbaby Cup Holder Bedienungsanleitung

Elko

Elko SmartSensor Leakage Wireless Bedienungsanleitung

Grizzly

Grizzly H8371 Bedienungsanleitung

Panasonic

Panasonic HG-T Series Bedienungsanleitung

IFM Electronic

IFM Electronic Efector 250 Series Referenzhandbuch

Virtuox

Virtuox VirtuCLEAN 2.0 Bedienungsanleitung

DigiDesign

DigiDesign 888/24 I/O Bedienungsanleitung

PROZIS

PROZIS QUAY Bedienungsanleitung

patagonia

patagonia PSI Vest Bedienungsanleitung

SFC Energy

SFC Energy EFOY GO! Bedienungsanleitung