Chamberlain 320LM Bedienungsanleitung

To comply with FCC/IC rules, adjustment or modifications of this receiver

and/or transmitter are prohibited, except for changing the code setting or

replacing the battery. THERE ARE NO OTHER USER SERVICEABLE

PARTS.

Universal Radio Control

OWNERS MANUAL

Children operating or playing with a garage

door opener can injure themselves or others.

The garage door could close and cause

serious injury or death. Do not allow children

to operate the wall push button(s) or remote

control transmitter(s).

A moving garage door could injure or kill

someone under it. Activate the opener only

when you can see the door clearly, it is free of

obstructions, and is properly adjusted.

WARNING

Disconnect power to the garage door opener

before proceeding.

WARNING

NOTE: With the transformer, use a 2 wire

connection ONLY. Attach mounting clips to the

receiver terminals 1 and 2, and to the opener

terminals used for push button controls. Plug the

transformer into the receiver as shown, and into a

120 Volt outlet.

Side 2 contains installation and service

information as well as code setting instruction for

models with transmitter(s).

MOUNTING RECEIVER ON OPENER

Fully extend antenna wire below bottom of case as

shown.

Loosen the two receiver terminal screws labeled 1

and 2. Insert one end of a mounting clip under each

terminal. Make sure the clips are positioned to clear

the receiver flange, as shown. DO NOT RETIGHTEN

AT THIS TIME.

Loosen the two opener terminal screws used for push

button control.

Leaving the push button bell wire in place, insert the

other ends of the mounting clips under the opener

terminal screws.

If the number sequence of opener

terminals doesn’t match the receiver, turn the receiver

around (so back is facing out) and complete the

connection.

NOTE: Terminals 1 and 2 on the receiver MUST

be connected to the push button terminals on the

opener.

Retighten the terminal screws on the opener and

receiver. Reconnect power to the opener

. T

receiver push bar should light.

If it doesn’t light and

your opener has a radio power terminal, use the third

mounting clip to connect receiver terminal 3 to opener

terminal 3.

If the receiver push bar still doesn’t light, you

must use Transformer Model 85.

Model 320LM Model 320-1LM Model 320-2LM

Receiver Only (With 1 Transmitter) (With 2 Transmitters)

Model 85 transformer may be required if your

garage door opener is a brand other than

LiftMaster, Chamberlain or Sears.

NOTE: Models 320-1LM and 320-2LM are factory

pre-set with matching receiver and transmitter

codes.

THE RECEIVER MAY BE INSTALLED IN ONE OF

TWO WAYS:

1. Mounted directly on the door opener with clips

provided as described below.

2. Attached to an inside wall of the garage with

connecting bell wire (not supplied), described on

side two.

When installing two or more receivers in a garage,

position them at least 10 feet apart to prevent

electronic interference.

To Outlet

Model 85

Transformer

OPENER

TERMINALS

Receiver

Terminals

Antenna Wire Fully Extended

Flange Mounting

Clip #1

Mounting

Clip #2

Mounting

Clip #3

Common

Push Button

Radio Power

SET RECEIVER TO MATCH TRANSMITTER(S) CODE

Pry open the front panel of receiver case with a coin

or a screwdriver.

1. Press and

hold

the transmitter push button.

2. Then press the "Smart" button on the receiver. The

adjacent indicator light will

flash

once. Now the

opener will operate when the push button on either

the receiver or the transmitter is pressed.

Repeat Steps 1 and 2 for each transmitter that will

be used to operate the garage door opener.

NOTE: If the remote control push button is not

pressed within 30 seconds, receiver indicator

light will turn OFF. Repeat Steps 1 and 2.

To Erase All Transmitter Codes

• Press and hold the "Smart" code button on the

opener panel until the indicator light turns off (about

6 seconds).

All

the codes the opener has

learned will be erased.

• Repeat Steps 1 and 2 to reprogram the receiver for

each transmitter in use.

Transmitter

Push Button

Smart

Button

Indicator Light

MOUNTING RECEIVER ON GARAGE WALL

Fully extend the antenna wire below bottom of case

as shown.

Fasten the receiver to an inside garage wall with the

screws provided. A convenient place is alongside the

service door and OUT OF THE REACH OF

CHILDREN.

Use existing bell wire, if desired. Attached one end of

2-strand wire to receiver terminals 1 and 2. The other

end must be connected to the two opener terminals

which are used for the push button control. Use

insulated staples to secure bell wire between receiver

and opener.

Reconnect power to the opener. The receiver push bar

should light. If it doesn’t light and the opener has three

terminals, use a third strand of bell wire to connect

receiver terminal 3 to the third opener terminal.

If the receiver push bar still doesn’t light, use

Transformer Model 85.

NOTE: With the transformer, use a 2-wire

connection ONLY. Attach wire to receiver terminals

1 and 2 and to the opener terminals used for push

button control. Plug transformer into receiver and

120 Volt outlet as shown.

To Wall Outlet

Model 85

Transformer

OPENER

WALL

PUSH

BUTTON

TRANS

PRIMARY

24v

Universal Radio

Control (Top)

Common

Push Button

Radio Pwr.

#3 Connection

(optional)

Dieses Handbuch passt für folgende Modelle

Andere Chamberlain Controller Handbücher

Chamberlain

Chamberlain CAP2D Bedienungsanleitung

Chamberlain

Chamberlain SUB324M Bedienungsanleitung

Chamberlain

Chamberlain 041DJ002 Bedienungsanleitung

Chamberlain

Chamberlain CAP2D Bedienungsanleitung

Chamberlain

Chamberlain CLDM1ANZ Bedienungsanleitung

Chamberlain

Chamberlain SECURITY+ WPB3LM3 Bedienungsanleitung

Chamberlain

Chamberlain 945C Bedienungsanleitung

Chamberlain

Chamberlain 872 Series Bedienungsanleitung

Chamberlain

Chamberlain CLLACD Bedienungsanleitung

Chamberlain

Chamberlain SMART GARAGE CONTROL Bedienungsanleitung

Chamberlain

Chamberlain LiftMaster Professional 915LM Bedienungsanleitung

Chamberlain

Chamberlain T Bedienungsanleitung

Chamberlain

Chamberlain myQ 821LM Bedienungsanleitung

Chamberlain

Chamberlain 855CB Bedienungsanleitung

Chamberlain

Chamberlain LiftMaster K001A6039 Bedienungsanleitung

Chamberlain

Chamberlain Garos CS 300 Bedienungsanleitung

Chamberlain

Chamberlain RED/GREEN LIGHT CONTROL KIT Bedienungsanleitung

Chamberlain

Chamberlain LA400UL Kurzanleitung

Chamberlain

Chamberlain LiftMaster Professional CB224 Bedienungsanleitung

Chamberlain

Chamberlain Motorlift GWAP120 Bedienungsanleitung

Chamberlain

Chamberlain LA412UL Kurzanleitung

Chamberlain

Chamberlain AGO250L Bedienungsanleitung

Chamberlain

Chamberlain 883LMW Bedienungsanleitung

Chamberlain

Chamberlain Liftmaster PROFESSIONAL 412-315HM Bedienungsanleitung

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung

3M MicroTouch EX113 Bedienungsanleitung

KUHN

KUHN TKS Bedienungsanleitung

S&C

S&C PMH Bedienungs- und Wartungshandbuch