Chauvet Epix Drive 642 Bedienungsanleitung

Page 1 o

Quick Reference Guide

English EN

Español ES

Français FR

ÉPIX™ Drive 642 QRG EN

Safety

Notes

Read all the following Safety Notes before working with this

product. These notes include important information about the

installation, usage, and maintenance of this product.

This icon indicates critical installation, configuration, or

operation information. Failure to comply with this information

may render the fixture partially or completely inoperative,

damage third-party equipment, or cause harm to the user.

There are no user-serviceable parts in this product. Any

reference to servicing in this guide applies only to properly

certified Chauvet technicians. Do not open the housing or

attempt any repairs unless you are certified by Chauvet.

This icon indicates useful, although non-critical information.

•DO NOT open this product. It contains no user-serviceable parts.

•To eliminate unnecessary wear and improve its lifespan, during periods of non-use

completely disconnect the product from power via breaker or by unplugging it.

•CAUTION: When transferring product from extreme temperature environments, (e.g.

cold truck to warm humid ball

room) condensation may form on the internal electronics

of the product. To avoid causing a failure, allow product to fully acclimate to the

surrounding environment before connecting it to power.

•CAUTION: This product’s housing may be hot when lights are operating.

•Mount this product in a location with adequate ventilation, at least 20 in (50 cm) from

adjacent surfaces.

•DO NOT leave any flammable material within 50 cm of this product while operating or

connected to power.

•This product is for indoor use only! To prevent risk of fire or shock, do not expose this

product to rain or moisture.

•DO NOT connect this product to a dimmer or rheostat.

•ONLY connect this product to a grounded and protected circuit.

•Always make sure you are connecting this product to the proper voltage, as per the

Technical Specifications in this guide or on the product’s specification label.

•Do not operate this product if you see damage on the housing, I/O ports, or cables.

Have the damaged parts replaced by an Chauvet certified technician at once.

•Do not cover the ventilation slots when operating to avoid internal overheating.

•The maximum ambient temperature is 104 °F (40 °C). Do not operate

this product at a

higher temperature.

•In case of a serious operating problem, stop using this product immediately!

EN ÉPIX™ Drive 642 QRG

What Is Included

Once you receive the product, carefully open the package and make sure all the

pieces included are in good condition. The followng items should be included in

the package:

•EPIX™ Drive 642

•NEUTRIK® powerCON® to Edison Plug Input Power Cord

•Warranty Card

•Quick Reference Guide

If there are any missing pieces, please contact the local dealer where you

purchased the product.

Installation Procedure

Before installing any product, you should completely read through the guide that

was shipped with the product.

1. Carefully remove all items from the package and place on a secure

foundation.

2. Mount product.

3. Connect product to computer/controller via router.

4. Connect ÉPIX™ Strip 2.0 and/or Bar 2.0.

5. Install power cable and connect to power.

ÉPIX™ Drive 642 QRG EN

Product Overview

ÉPIX™ Drive 642 hosts the processing and power supply for the EPIX™ 2.0

product line in one convenient device. It controls up to 16 ÉPIX™ Strip 2.0 4

ÉPIX™ Tile 2.0, or 4 ÉPIX™ Bar 2.0 using Art-Net™ (3.0 compliant) or Arkaos

Kling-Net. Additionally, you can manage configuration and software updates

with a network-based remote web server.

Front View

Art-Net™/Kling-

Net In/Out

Power Output

Mounting/Safety Points

ÉPIX™ Strip 2.0, ÉPIX™

Tile 2.0 or ÉPIX™ Bar

2.0 Output

Power Input

Side Views

EN ÉPIX™ Drive 642 QRG

Mounting

The ÉPIX™ Drive 642 has four (4) mounting points (one on each corner) with 13

mm holes to which you can install screws and mount this product directly to

almost any flat surface, truss, or other load bearing structure in any orientation.

The product may also be installed with clamps for hanging on truss. You must

supply your own clamps and make sure the clamps are capable of supporting

the weight of this product.

Mounting Guidelines

Chauvet recommends using the following guidelines when mounting this

product:

•Make sure to mount this product away from any flammable material as indicated

in the Safety Notes section.

•Never mount in places where rain, high humidity, extreme temperature changes,

or restricted ventilation may affect the product.

•Before deciding on a location, always make sure there is easy access to

the product for maintenance and programming.

•Make sure that the structure or surface onto which you are mounting the

product can support the product’s weight (see the Technical

Specifications).

•When mounting the product overhead, always use a safety cable.

Mount the product securely to a rigging point, such as an elevated

platform or a truss.

•When rigging the product onto a truss, you should use a mounting

clamp of appropriate weight capacity.

•When mounting the product on the floor, make sure that the product and

cables are away from people and vehicles.

ÉPIX™ Drive 642 QRG EN

Mounting Instructions

Mounting hardware is not included with the product.

Using Mounting Clamps:

1. Attach the clamp to the mounting bracket.

2. Attach a safety cable to the product’s safety

loop.

3. Attach the clamp to the desired structure or surface.

4. Attach a safety cable through the mounting points.

Using Mounting Points:

1. Screw product in the mounting points

securely into a mounting surface.

EN ÉPIX™ Drive 642 QRG

Signal Connections

Art-Net™ Connection

Art-Net™ is an Ethernet protocol that uses TCP/IP that transfers large amount of

DMX512 data using an etherCON® RJ45 connection over a large network. An Art-Net™

protocol document is available from www.chauvetpro.com.Art-Net™ is designed and

copyrighted by Artistic Licence Holdings Ltd.

This product is not designed to respond to controllers sending in Broadcast mode via

Art-Net™. For best results, use Unicast mode. For information about which control

protocol your controller uses, please contact the manufacturer of your controller.

Kling-Net Connection

Kling-Net is a network protocol that allows auto configuration of display devices using an

etherCON® RJ45 Ethernet connection. Refer to the ArKaos software manual for detailed

instructions on programming this product.

For smooth-running operation, ArKaos Kling-Net requires a gigabit (1000 Mbps) Ethernet card

and network router.

Do not use

WAN port!

Computer/Controller

(running Kling-Net

or Art-Net™ protocol)

Router

ÉPIX™

Drive 642

To other Kling-Net

or Art-Net™ Devices

ÉPIX™ Drive 642 QRG EN

Connecting ÉPIX™ Products to the Power Supply

The ÉPIX™ Drive 642 uses an RJ45 data connection to link all data ports. You

can connect either 4- ÉPIX™ strips, 1 ÉPIX™ Tile 2.0 or 1- ÉPIX™ Bar per

output on the ÉPIX™ Drive 642. The following diagram illustrates how to

assemble the data connections.

Each port of ÉPIX™ Drive 642 can support 1 pc. ÉPIX™ Bar 2.0, ÉPIX™ Tile 2.0 or 4 pcs.

ÉPIX™ Strip 2.0. Make sure the total length of the connecting network cables (RJ45)

does not exceed 10 meters.

Be sure power is disconnected from the ÉPIX™ Drive 642 before connecting any ÉPIX™

2.0 products. Failure to do so may cause damage and void your warranty.

Total length

of cables

cannot

exceed 10 m

Total length

of cables

cannot

exceed 10 m

EN ÉPIX™ Drive 642 QRG

Software Upgrade Instructions

These instructions below apply to VERSION 1 hardware only. Do Not load VERSION 2

software onto VERSION 1 hardware.

The following steps refer to the Windows® 7 operating system environment.

Step 1:

1. Connect the ÉPIX™ Drive 642 to the

router.

Verify the computer is using the same

network as the ÉPIX™ Drive 642

product.

Step 2:

From the ÉPIX™ Drive 642

main level,

navigate to Input Mode > Art-Net.

Step 3:

Select IP Mode.

Select <Static>.

Step 4:

From the Windows® start menu, click

the <Start> button.

From the Search box, type Network

and Sharing Center. Windows will

generate the

search results in the Start

window.

Select Network and Sharing Center,

and the Network and Sharing Center

dialog appears.

IP Mode

Static

Input Mode

Art-Net

ÉPIX™ Drive 642 QRG EN

Step 5:

Select the desired network the

product is connected to.

If you are running a hard-

wired line

from the PC to your

router, then select

Local Area Connection. The Local Area

Connection Status dialog appears.

2. Click Properties. The Local Area

Connection Properties dialog

appears.

Step 6:

1. From the Networking tab, select

Internet Protocol Version 4

(TCP/IPv4).

2. Click Properties. The Internet

Protocol Version 4 (TCP/IPv4)

Properties dialog appears.

Step 7:

1. From the General tab, select Use the

following IP address:.

2. Enter the following information:

3. Enter 2.255.0.0 in the IP address box.

4. Enter 255.255.255.0 in the Subnet

mask box.

5. Click OK.

6. Close existing dialogs that are

currently open.

7. Minimize the Control Panel, as it will

be necessary to access this window

after the software upgrade is

uploaded to the product.

2. 255 .0.0

255 . 255 . 255 . 0

Andere Handbücher für Epix Drive 642

Inhaltsverzeichnis

Sprachen:

Andere Chauvet Scheinwerfer Handbücher

Chauvet

Chauvet Hurricane 700 Bedienungsanleitung

Chauvet

Chauvet Hemisphere 5.1 Bedienungsanleitung

Chauvet

Chauvet MegaStrobe FX 12 Bedienungsanleitung

Chauvet

Chauvet 4 Bar Flex Bedienungsanleitung

Chauvet

Chauvet COLORado Ridge IP Bedienungsanleitung

Chauvet

Chauvet Rogue R1 FX-B Bedienungsanleitung

Chauvet

Chauvet LED Pinspot 360 Bedienungsanleitung

Chauvet

Chauvet 4 Bar Flex Bedienungsanleitung

Chauvet

Chauvet Strike 4 Bedienungsanleitung

Chauvet

Chauvet EZwash HEX Pack Bedienungsanleitung

Chauvet

Chauvet LFS-5D Bedienungsanleitung

Chauvet

Chauvet SlimPANEL TRI 12 IP Bedienungsanleitung

Chauvet

Chauvet COLORado Batten 144 Tour Bedienungsanleitung

Chauvet

Chauvet SlimPANEL TRI 12 IP Bedienungsanleitung

Chauvet

Chauvet COLORdash Batten-Hex 8 Bedienungsanleitung

Chauvet

Chauvet Freedom Par RGBA Bedienungsanleitung

Chauvet

Chauvet Freedom Stick Bedienungsanleitung

Chauvet

Chauvet PowerStream 4 Bedienungsanleitung

Chauvet

Chauvet LEDRain 56C Bedienungsanleitung

Chauvet

Chauvet COLORado 2-Quad Zoom IP Bedienungsanleitung

Chauvet

Chauvet COLORband PiX Bedienungsanleitung

Chauvet

Chauvet Strike 882 Bedienungsanleitung

Chauvet

Chauvet LED PAR 38-18UVB Bedienungsanleitung

Chauvet

Chauvet DIAMONDstrip Mini Bedienungsanleitung

Beliebte Scheinwerfer Handbücher anderer Marken

VIZULO

VIZULO Micro Martin Benutzerhandbuch

EuroLite

EuroLite LED IP FL-100 SMD Bedienungsanleitung

Cooper Wheelock

Cooper Wheelock XB12 Bedienungsanleitung

Allen + Roth

Allen + Roth 17624-000 Bedienungsanleitung

ADJ

ADJ 4 STAGE PAK Bedienungsanleitung

Cooper Lighting

Cooper Lighting EGL91SW233 Bedienungsanleitung

Max

Max 37496 Bedienungsanleitung

BEGA

BEGA 85 143 Bedienungsanleitung

Beamz

Beamz 151.226 Bedienungsanleitung

EuroLite

EuroLite LED IP FL-8 Bedienungsanleitung

Ledj

Ledj PERFORMER 36 RGB Bedienungsanleitung

Perel

Perel ELS3 Bedienungsanleitung

Perel

Perel ELS3WD Bedienungsanleitung

LumX

LumX LM 36130 Bedienungsanleitung

Xtricity

Xtricity 4-80053 Bedienungsanleitung

Stahl

Stahl 6521/4 Series Bedienungsanleitung

Ecosense

Ecosense EcoSpec Bedienungsanleitung

Ayrton

Ayrton minipanel FX Bedienungsanleitung