Chauvet Rogue r2 Beam Bedienungsanleitung

Quick Reference Guide

English EN

Español ES

Français FR

Nederlands NL

Rogue™ R2 Beam QRG EN

About This Guide

The Rogue™ R2 Beam Quick Reference Guide (QRG) has basic product

information such as connection, mounting, menu options, and DMX values.

Download the User Manual from www.chauvetprofessional.com for more details.

Disclaimer

The information and specifications contained in this QRG are subject to change

without notice.

Safety Notes

• DO NOT open this product. It contains no user-serviceable parts.

• DO NOT look at the light source when the product is on.

• To eliminate unnecessary wear and improve its lifespan, during periods of

non-use completely disconnect the product from power via breaker or by

unplugging it.

• CAUTION: When transferring product from extreme temperature

environments, (e.g. cold truck to warm humid ballroom) condensation may

form on the internal electronics of the product. To avoid causing a failure,

allow product to fully acclimate to the surrounding environment before

connecting it to power.

• CAUTION: This product’s housing may be hot when lights are operating.

• Mount this product in a location with adequate ventilation, at least

20 in (50 cm) from adjacent surfaces.

• DO NOT leave any flammable material within 50 cm of this product while

operating or connected to power.

• USE a safety cable when mounting this product overhead.

• DO NOT operate this product outdoors or in any location where dust,

excessive heat, water, or humidity may affect it. (IP20)

• DO NOT operate this product if the housing, lenses, or cables appear

damaged.

• DO NOT connect this product to a dimmer or rheostat.

• ONLY connect this product to a grounded and protected circuit.

• ONLY use the mounting brackets or the handles to carry this product. Do not

carry by the moving head.

• In the event of a serious operating problem, stop using immediately.

• The maximum ambient temperature is 113 °F (45 °C). Do not operate this

product at higher temperatures.

Contact

Outside the U.S., United Kingdom, Ireland, Mexico, or Benelux, contact your

distributor to request support or return a product. From inside

the U.S., UK,

Ireland, Mexico, or Benelux, use the information in Contact Us

at the end of this

QRG.

What Is

Included

• Rogue™ R2 Beam

• Neutrik® powerCON® power cord

•

2 Omega brackets with mounting hardware

• Warranty Card

• Quick Reference Guide

AC Power

This product has an auto-ranging power supply that can work with an input voltage

range of 100–240 VAC, 50/60 Hz.

To eliminate unnecessary wear and improve its lifespan, during periods of

non-use completely disconnect the

product from power via breaker or by

unplugging it.

AC Plug

Connection

Wire (U.S.)

Wire (Europe)

Screw Color

AC Live

Black

Brown

Yellow/Brass

AC Neutral

White

Blue

Silver

AC Ground

Green/Yellow

Green

Rogue™ R2 Beam QRG EN

Replacing The

Fuse

1. Disconnect this product from power.

2. Using a flat-head screwdriver, unscrew the fuse holder cap from the housing.

3. Remove blown fuse and replace with a good fuse of the same type and rating.

4. Screw the fuse holder cap back in place and reconnect power.

Lamp

Replacement

1. Turn the fixture off and disconnect it from power.

2. Wait at least 15 minutes for the lamp to cool down.

3. Remove both head covers by removing 8 Phillips-head ¼-turn screws.

4. Orient the rear of the product so that the fan is facing upward.

5. Remove the 2 Phillips-head screws on the sides of the fan assembly.

6. Roll the fan assembly to the right to expose the lamp.

Using the lamp base, push the lamp down against the spring clips located on the

bottom, then roll the lamp out the top.

8. Remove the 2 wires connected to the lamp by the spade terminals.

9. Reverse the steps above to install the new lamp.

Please refer to the User Manual for more detailed instructions with images.

¼-turn

Phillips-head

screws

Rogue™ R2 Beam QRG EN

DMX Linking

The Rogue™ R2 Beam will work with a DMX controller using a 3- or 5-pin DMX

data connection. A DMX Primer is available from www.chauvetprofessional.com

DMX Connection

The Rogue™ R2 Beam uses a 3- or 5-pin DMX data connection for its DMX

personalities: 15CH and 18CH.

See the User Manual for information about

connecting and configuring the product for DMX operation.

Mounting

Before mounting this product, read the Safety Notes. Use at least two mounting

points

per product. Make sure the mounting clamps are capable of supporting the

weight of the product. For our CHAUVET® line of mounting clamps, g

o to

trusst.com/productcategory/base-plates-accessories-clamps/.

Product

Mounting

Diagram

Control Panel

Description

Button

Function

<MENU>

Exits from the current menu or function

<ENTER>

Enables the currently displayed menu or sets the currently

selected value into the selected function

<UP>

Navigates upwards through the menu list or increases the

numeric value when in a function

<DOWN>

Navigates downwards through the menu list or decreases the

numeric value when in a function

Overhead Mounting

Floor Mounting

Mounting

Clamp

Safety Cable

Omega Bracket

Rogue™ R2 Beam QRG EN

Menu Map

Main Level

Programming Levels

Description

Address

001–512

Sets the DMX starting address

Run Mode

DMX

15CH

Selects the DMX mode

18CH

Auto Test

Runs the product’s test sequence

Manual Test

Pan

000–255 Allows manual control of all settings from

the control panel

Pan Fine

Tilt

Tilt Fine

P/T Speed

Dimmer

Fine

Shutter

Color

Gobo

Prism

R–Prism

Zoom

Focus

Frost

P/T Macro

P/T

Ma.Speed

Special

Function

Rogue™ R2 Beam QRG EN

Menu Map (Cont.)

Main Level

Programming Levels

Description

Setup

Pan Reverse

YES

Reverse pan operation

Normal pan operation

Tilt Reverse

YES

Reverse tilt operation

Normal tilt operation

Screen Reverse

YES

Rotates control screen view 180°

Normal control screen view

Pan Angle

540

Selects the 540° pan angle range

360

Selects the 360° pan angle range

180

Selects the 180° pan angle range

Tilt Angle

270

Selects the 270° tilt angle range

180

Selects the 180° tilt angle range

Selects the 90° tilt angle range

BL.O.P/T Move

YES

Defines the pan/tilt move-in-black delay

BL.O.ColorMove

YES

Defines the color change move-in-black

delay

BL.O.GoboMove

YES

Defines the gobo change move-in-black

delay

Lamp Settings

On/Off

Turns lamp on/off

OFF

State/Power

Defines the status of lamp when powering

up product

OFF

Off Via Dmx

YES

Turns off the unit via DMX controller

On If Dmx

YES

Turns lamp on when DMX signal is

detected

Off If Dmx

Off

YES

Turns lamp off when DMX signal is lost

Ignition

Delay

000–255

Selects duration of delay between product

power on and lamp power on

Low Power

Delay 000–255

Selects the duration of delay when shutter

is closed and lamp enters lower power

state

Reset Lamp

Time

YES

Resets lamp timer to 0

Leaves lamp time unchanged

Rogue™ R2 Beam QRG EN

Menu Map (Cont.)

Main Level

Programming Levels

Description

Setup

(Cont.)

Maintenance

Timer

Interval 10–250

Defines amount of hours between

maintenance

Remaining

Time

Shows amount of time remaining in

maintenance cycle

RESET

Resets the time back to the beginning

Reset Function

Pan/Tilt

YES

Resets pan/tilt functions to the home

position

Shutter/

Prism

YES

Resets all shutter/prism functions to the

home position

Color

YES

Resets all color functions to the home

position

Gobo

YES

Resets all gobo functions to the home

position

Zoom/Frost

/Focus

YES

Resets the zoom, frost, and focus

functions to the home position

All

YES

Resets all functions to the home position

Factory Settings

YES

Reverts the product back to the original

factory settings

Sys Info

Ver:

Displays the software version

Running Mode:

Displays the current running mode

Dmx Address:

Displays the current DMX address

Temperature:

Displays the product’s temperature in

Celsius

Lamp On Time:

Displays the amount of time the lamp has

been on (provided the counter has been

reset upon installation of new lamp)

Remain Time:

Shows amount of time remaining in

maintenance cycle

Rogue™ R2 Beam QRG EN

DMX Values

18CH

Channel

Function

Value

Percent/Setting

Pan

000ó255

0–100%

Fine Pan

000ó255

0–100%

Tilt

000ó255

0–100%

Fine Tilt

000ó255

0–100%

Pan/Tilt Speed

000ó255

0–100%

Dimmer

000ó255

0–100%

Fine Dimmer

000ó255

0–100%

8 Shutter

000ó007

008ó015

016ó131

132ó167

168ó203

204ó239

240ó247

248

255

Closed

Open

Slow to fast

Fast close, slow open from slow to fast

Slow close, fast open from slow to fast

Pulse effect from slow to fast

Random effect from slow to fast

Open

9 Color Wheel

000ó004

005ó008

009ó012

013ó016

017ó020

021ó024

025ó028

029ó032

033ó036

037ó040

041ó044

045ó048

049ó052

053ó056

057ó060

061ó127

128ó189

190ó193

194ó255

Open

Red

Deep yellow

Turquoise

Green

Light green

Light purple

Pink

Light yellow

Magenta

Blue

CTO 3200 K

CTO 5600 K

CTO 6500 K

Split colors

Clockwise color scroll, fast to slow

Stop

Counter-clockwise color scroll, slow to fast

Rogue™ R2 Beam QRG EN

DMX Values (Cont.)

18CH

(Cont.)

Channel

Function

Value

Percent/Setting

10 Gobo Wheel

000ó003

004ó006

007ó009

010ó012

013ó015

016ó018

019ó021

022ó024

025ó027

028ó030

031ó033

034ó036

037ó039

040ó042

043ó045

046ó048

049ó051

052ó055

056ó059

060ó127

128ó189

190ó193

194ó255

Open

Gobo 1

Gobo 2

Gobo 3

Gobo 4

Gobo 5

Gobo 6

Gobo 7

Gobo 8

Gobo 9

Gobo 10

Gobo 11

Gobo 12

Gobo 13

Gobo 14

Gobo 15

Gobo 16

Gobo 17

Open

Gobo shake 1–17, slow to fast

Clockwise gobo scroll, fast to slow

Stop

Counter-clockwise gobo scroll, slow to fast

11 Prism

000ó004

005ó255

No function

Prism insert

12 Prism Rotate

000ó127

128ó189

190ó193

194ó255

Prism index

Counter-clockwise rotation, fast to slow

Stop

Clockwise rotation, slow to fast

Prism Zoom

000ó255

0–100%

Focus

000ó255

0–100%

Frost

000ó255

0–100%

Rogue™ R2 Beam QRG EN

DMX Values (Cont.)

18CH

(Cont.)

Channel

Function

Value

Percent/Setting

16 Movement Macros

000ó007

008ó015

016ó023

024ó031

032ó039

040ó047

048ó055

056ó063

064ó071

072ó079

080ó087

088ó095

096ó103

104ó111

112ó119

120ó127

128ó135

136ó143

144ó151

152ó159

160ó167

168ó175

176ó183

184ó191

192ó199

200ó207

208ó215

216ó223

224ó231

232ó239

240ó247

248ó255

No function

Effect 1

Effect 2

Effect 3

Effect 4

Effect 5

Effect 6

Effect 7

Effect 8

Effect 9

Effect 10

Effect 11

Effect 12

Effect 13

Effect 14

Effect 15

Effect 16

Effect 17

Effect 18

Effect 19

Effect 20

Effect 21

Effect 22

Effect 23

Effect 24

Effect 25

Effect 26

Effect 27

Effect 28

Effect 29

Effect 30

Effect 31

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere Chauvet Scheinwerfer Handbücher

Chauvet

Chauvet ColorAdo 2 Tour Bedienungsanleitung

Chauvet

Chauvet Colordash Bedienungsanleitung

Chauvet

Chauvet SlimPAR 56 IRC IP Bedienungsanleitung

Chauvet

Chauvet PowerStream 4 Bedienungsanleitung

Chauvet

Chauvet COLORband PiX Bedienungsanleitung

Chauvet

Chauvet Swarm 4 Bedienungsanleitung

Chauvet

Chauvet BEAMSHOT Bedienungsanleitung

Chauvet

Chauvet COLORdash Par-Hex 7 Bedienungsanleitung

Chauvet

Chauvet COLORado Ridge IP Bedienungsanleitung

Chauvet

Chauvet COLORband PiX Bedienungsanleitung

Chauvet

Chauvet Comet LED Bedienungsanleitung

Chauvet

Chauvet COLORado 1 Tour Bedienungsanleitung

Chauvet

Chauvet ROGUE RH1 Hybrid Bedienungsanleitung

Chauvet

Chauvet Strike 882 Bedienungsanleitung

Chauvet

Chauvet SX Mix Bedienungsanleitung

Chauvet

Chauvet Bubble King Bedienungsanleitung

Chauvet

Chauvet HURRICANE 1100 Bedienungsanleitung

Chauvet

Chauvet Scorpion GVC Bedienungsanleitung

Chauvet

Chauvet COLORado Batten 72 Tour Bedienungsanleitung

Chauvet

Chauvet COLORado Panel Bedienungsanleitung

Chauvet

Chauvet SkyScan 4000 Bedienungsanleitung

Chauvet

Chauvet Legend 412 QRG Bedienungsanleitung

Chauvet

Chauvet Pocketspot LED Bedienungsanleitung

Chauvet

Chauvet GigBAR IRC Bedienungsanleitung

Beliebte Scheinwerfer Handbücher anderer Marken

VIZULO

VIZULO Micro Martin Benutzerhandbuch

EuroLite

EuroLite LED IP FL-100 SMD Bedienungsanleitung

Cooper Wheelock

Cooper Wheelock XB12 Bedienungsanleitung

Allen + Roth

Allen + Roth 17624-000 Bedienungsanleitung

ADJ

ADJ 4 STAGE PAK Bedienungsanleitung

Cooper Lighting

Cooper Lighting EGL91SW233 Bedienungsanleitung

Max

Max 37496 Bedienungsanleitung

BEGA

BEGA 85 143 Bedienungsanleitung

Beamz

Beamz 151.226 Bedienungsanleitung

EuroLite

EuroLite LED IP FL-8 Bedienungsanleitung

Ledj

Ledj PERFORMER 36 RGB Bedienungsanleitung

Perel

Perel ELS3 Bedienungsanleitung

Perel

Perel ELS3WD Bedienungsanleitung

LumX

LumX LM 36130 Bedienungsanleitung

Xtricity

Xtricity 4-80053 Bedienungsanleitung

Stahl

Stahl 6521/4 Series Bedienungsanleitung

Ecosense

Ecosense EcoSpec Bedienungsanleitung

Ayrton

Ayrton minipanel FX Bedienungsanleitung