Chicago Electric 46225 Bedienungsanleitung

10” TILE SAW,

2.5 HP WITH PVC TRAY

ASSEMBLY AND OPERATING INSTRUCTIONS

3491 Mission Oaks Blvd., Camarillo, CA 93011

Visit our Web site at http://www.harborfreight.com

manual or any artwork contained herein may be reproduced in any shape or form

without the express written consent of Harbor Freight Tools.

For technical questions and replacement parts, please call 1-800-444-3353.

46225

SKU 46225 For technical questions, please call 1-800-444-3353. Page 2

Specifications

Save This Manual

You will need the manual for the safety warnings and precautions, assembly in-

structions, operating and maintenance procedures, parts list and diagram. Keep

your invoice with this manual. Write the invoice number on the inside of the front

cover. Keep the manual and invoice in a safe and dry place for future reference.

Safety Warnings and Precautions

WARNING: When using tool, basic safety precautions should always be fol-

lowed to reduce the risk of personal injury and damage to equipment.

Read all instructions before using this tool!

1. Keep work area clean. Cluttered areas invite injuries.

2. Observe work area conditions. Do not use machines or power tools in damp

or wet locations. Don’t expose to rain. Keep work area well lighted. Do not use

electrically powered tools in the presence of flammable gases or liquids.

3. Keep children away. Children must never be allowed in the work area. Do

not let them handle machines, tools, or extension cords.

4. Store idle equipment. When not in use, tools must be stored in a dry location

to inhibit rust. Always lock up tools and keep out of reach of children.

5. Do not force tool. It will do the job better and more safely at the rate for which

it was intended. Do not use inappropriate attachments in an attempt to exceed

the tool capacity.

ITEM

Overall Dimensions

Table Dimensions

Water Tray Dimensions

Cut Capacity

Blade Specs.

(Blade not included)

Motor Specs.

Construction

Cord Specs.

Pump Max. Flow

Net Weight

DESCRIPTION

39-3/4”L x 21”W x 48-3/4”H

16-3/8” x 11-1/8”

35-1/4” x 18-1/2” x 3”D (outside)

Rips, 18”; Diag., 12”; Depth, 3-3/4”

10” Continuous Rim Blade (not

included), 0.050” Thick, Metal

Bonded Diamonds

3340 RPM, 2-1/2 HP, 115 V/120V, 60

HZ, 15 Amps, 1800 Watts, Single Phase

Low Carbon Steel and Cast

Aluminum

3-Prong Plug, Double Insulated, 6’L,

14 AWG, UL Approved

10-12 liters per minute

107 Lbs.

10 NJ

E180772

REV 02/06, 08/06

SKU 46225 For technical questions, please call 1-800-444-3353. Page 3

6. Use the right tool for the job. Do not attempt to force a small tool or attachment

to do the work of a larger industrial tool. There are certain applications for

which this tool was designed. Do not modify this tool and do not use this tool

for a purpose for which it was not intended.

7. Dress properly. Do not wear loose clothing or jewelry as they can be caught

in moving parts. Protective, electrically nonconductive clothes and nonskid

footwear are recommended when working. Wear restrictive hair covering to

contain long hair.

8. Use eye and ear protection. Always wear ANSI approved impact safety

goggles.

9. Do not overreach. Keep proper footing and balance at all times. Do not reach

over or across running machines.

10. Maintain tools with care. Keep tools sharp and clean for better and safer

performance. Follow instructions for lubricating and changing accessories.

Inspect tool cords periodically and, if damaged, have them repaired by an

authorized technician. The handles must be kept clean, dry, and free from oil

and grease at all times.

11. Disconnect power. Unplug tool when not in use.

12. Remove adjusting keys and wrenches. Check that keys and adjusting

wrenches are removed from the tool or machine work surface before plugging

it in.

13. Avoid unintentional starting. Be sure the switch is in the Off position when

not in use and before plugging in.

14. Stay alert. Watch what you are doing, use common sense. Do not operate

any tool when you are tired.

15. Check for damaged parts. Before using any tool, any part that appears

damaged should be carefully checked to determine that it will operate properly

and perform its intended function. Check for alignment and binding of moving

parts; any broken parts or mounting fixtures; and any other condition that may

affect proper operation. Any part that is damaged should be properly repaired

or replaced by a qualified technician. Do not use the tool if any switch does not

turn On and Off properly.

16. Guard against electric shock. Prevent body contact with grounded surfaces

such as pipes, radiators, ranges, and refrigerator enclosures.

17. Replacement parts and accessories. When servicing, use only identical

replacement parts. Use of any other parts will void the warranty. Only use

accessories intended for use with this tool. Approved accessories are available

from Harbor Freight Tools.

SKU 46225 For technical questions, please call 1-800-444-3353. Page 4

18. Do not operate tool if under the influence of alcohol or drugs. Read warning

labels on prescriptions to determine if your judgment or reflexes are impaired

while taking drugs. If there is any doubt, do not operate the tool.

19. Use proper size and type extension cord. If an extension cord is required, it

must be of the proper size and type to supply the correct current to the tool

without heating up. Otherwise, the extension cord could melt and catch fire, or

cause electrical damage to the tool. If you are using the tool outdoors, use an

extension cord rated for outdoor use (signified by “WA” on the jacket).

20. Maintenance. For your safety, service and maintenance should be performed

regularly by a qualified technician.

Note: Performance of this tool (if powered by line voltage) may vary depending on

variations in local line voltage. Extension cord usage may also affect tool perfor-

mance.

Warning: The warnings, cautions, and instructions discussed in this instruc-

tion manual cannot cover all possible conditions and situations that may oc-

cur. It must be understood by the operator that common sense and caution

are factors which cannot be built into this product, but must be supplied by

the operator.

Grounding/Voltage Warning

Warning: Before using this tool, make sure that the power cord will be plugged

into an outlet which has a three-prong ground, is 120V AC, is protected by a

30 Amp circuit breaker and has a Ground Fault Interrupter.

Common household current is 110-120V. As long as the outlet used with the Tile

Saw is rated from 110-120V there will be no complications using it with house-

hold receptacles. Plug the tool into a 110-120V properly grounded outlet pro-

tected by a 15-Amp, dual element time delay or circuit breaker.

NEVER try to plug a 110-120V tool into a 220-240V circuit, or serious complica-

tions and possible injury to the operator may occur. The plugs have different

shapes to prevent this.

This tool has a three-prong plug. The third round prong is the ground. Cutting off

the ground will result in a safety hazard and void the warranty.

If the outlet you are planning to use is the two-prong type, do not remove or alter

the grounding prong in any way. Use an adaptor and always connect the ground-

ing lug to a known grounding source. It is recommended that you have a qualified

electrician replace the two-prong outlet with a properly grounded three-prong

outlet.

SKU 46225 For technical questions, please call 1-800-444-3353. Page 5

Extension Cords

Your tool has a three-prong plug, therefore you must use a three-prong extension

cord. Only use rounded jacket extension cords listed by the UL. Improper use of

extension cords may cause inefficient operation of your tool which can result in

overheating. Be sure your extension cord is rated to allow sufficient current flow to

the Motor. If you are using the tool outdoors, use an extension cord rated for out-

door use (signified by “WA” on the jacket).

Unpacking

When unpacking, check to make all parts listed on Pages 10-11 are included. If any

parts are missing or broken, please call Harbor Freight Tools at the number on the

cover of this manual.

Note: Table Stand SKU #46310 is specifically designed for use with this 10” Tile

Saw and is not included. Stand is available for purchase from Harbor Freight Tools.

See Fig. 1 on Page 9 for a view of the Table Saw and Stand assembly.

If the Stand is not to be used with the Tile Saw, the Saw must be securely mounted

onto a flat, level surface capable of supporting the weight of the Tile Saw in addition

to the weight of all work pieces.

RECOMMENDED MINIMUM WIRE GAUGE FOR EXTENSION CORDS

(120 VOLT)

NAMEPLATE

AMPERES

(

At Full Load

)

EXTENSION CORD LENGTH

Feet

100

Feet

150

Feet

0 – 2.0 18 18 18 18 16

2.1 – 3.4 18 18 18 16 14

3.5 – 5.0 18 18 16 14 12

5.1 – 7.0 18 16 14 12 12

7.1 – 12.0 18 14 12 10 -

12.1 – 16.0 14 12 10 - -

16.1 – 20.0 12 10 - - -

* Based on limiting the line voltage drop

to five volts at 150% of the rated amperes.

Assembly

1. Slide the Water Tank [1] through the slots in the Machine Frame [6] so that the

entire Tank rests inside the Machine Frame.

2. Mount the Motor [19] to the Machine Frame by connecting the Supporting

Frame [12] to the Machine Frame at the point shown in the Assembly Diagram

on Page 12. Secure using two Bolts [7], Elastic Washers [8] and Big Flat

Washers [9] as shown.

3. Next, attach the Blade Guard [20] to the Motor using the Locking Knob [23]

and Flat Washer [24] provided. Please note: this product does not include a

Blade. Please see the following section, “Changing/Installing the Blade,” for

instructions on how to properly install a new Blade. REV 08/04

SKU 46225 For technical questions, please call 1-800-444-3353. Page 6

4. Plug the Pump [59] into the back of the Motor and attach the Pump to the

Water Tank using the four suction feet on the bottom of the Pump. See Fig. 2 on

Page 11.

5. Slide the Table Holder [51] through the middle of the Rail Cover [47] and fit the

two Inserts [45] over the ends of the Cover to prevent the Table Holder from

slipping out.

6. Attach the Rail and Table [52] Assembly you created in Step 5 to the Frame

using two sets of the Bolts [3], Flat Washers [4] and Teeth Washers [5] as

shown in the Assembly Diagram.

7. Before operating this tool, mount the Table Saw to the Table Stand (SKU #46310,

sold separately) by following the steps outlined in the Assembly and Operating

Instructions for the Table Stand. If the Stand is not to be used with the Tile Saw,

the Saw must be securely mounted onto a flat, level surface capable of

supporting the weight of the Tile Saw in addition to the weight of all work pieces.

Changing/Installing the Blade

1. Be sure the Power Cord is unplugged from its power source.

2. Loosen the Locking Knob located on the side of the Blade Guard [20] and

raise Guard. Tighten the Knob to lock the Guard in an “up” position.

3. Depress the Brake Shaft Button [26] (See Fig. 1 on Page 10) while turning the

Blade (or Spindle [44] if you have not yet installed a Blade) with your hand until

the Shaft button depresses fully. This will prevent the Spindle from spinning

and allow you to unscrew the Nut [29] and Outer Flange [30].

4. Slide the new Blade over the Spindle, and refasten the Outer Flange and Nut.

Be sure to tighten the Nut fully before use.

5. Lower the Blade Guard and tighten the Locking Knob.

Installing the Water Supply

To prevent excessive wear on the Blade, be sure to maintain a continuous flow of

water over the Blade while cutting. Never cut anything if the water flow is not con-

tinuous.

1. Attach the Pump as described in Step 4, “Assembly.” Position the Pump so it

will not interfere with the motion of the Table while cutting.

2. Fill the Water Tank with enough water so that the Pump is completely

submerged, but not so much water that the Tank overflows.

Note: When using the Tile Saw, extreme care must be taken to insure that the

Saw’s Power Cord is positioned to remain dry and free from water at all times.

Severe personal injury or death can occur if the Power Cord or the operator of

this tool should become wet at any time while this tool is in use. Care and

common sense must be used in planning a safe work area.

SKU 46225 For technical questions, please call 1-800-444-3353. Page 7

Operation

Preparing to Cut:

1. Mark the tile you wish to cut and place it aside for a moment.

2. Fill the Tank with water as described in “Installing the Water Supply,” above.

3. Plug the Pump’s Power Cord into the Power Unit. Make sure the Pump Power

Cord is positioned so it will remain in a dry location once the machine is in use.

If an extension cord is used, make sure it is of appropriate size and length

-see

Recommended Minimum Wire Gauge for Extension Cords

page 5.

4. When it is safe to do so, plug the Power Unit Cord into an appropriate outlet.

5. Put on your ANSI-approved eye protection.

6. Flip the Power Switch located on the front of the Motor (see Fig. 2 on Page 11)

to the “on” position.

7. Before operating the Tile Saw, let the Motor run for approximately one minute.

Make sure the Blade is rotating at full speed and there are no unusual noises.

If you feel the unit is not operating properly, do not use this tool.

8. To keep the pump working properly, the water in the tub may need to be

changed in the middle of a long project. Never allow the water to become

muddy or full of silt. When changing the water, always rinse out the intake of

the pump in clean water to help prevent silt buildup.

9. When finished, flip the power switch to the “off” position, unplug the unit, dispose

of the dirty water in an appropriate manner, rinse the pump’s inlet, and clean

any silt out of the bottom of the tank.

Cutting Tile:

1. Place your marked tile on the Table and brace it against the upturned edge

(Fence) on the back of the Table. Align the cut mark with the Blade.

2. Once the Tile Saw has been turned on, allow the Blade to spin up to full speed.

Watch to be sure that the Pump is supplying a continuous flow of water to the

Blade.

3. Keeping your hands clear of the Blade, move the Table and the tile underneath

the Blade. Feed the tile underneath the Blade very slowly. Do not force it. If the

rotational speed of the Blade slows down significantly, then you are forcing the

tile. No spectators should be allowed in the working area.

4. While cutting, watch to be sure that the Blade remains wet. If it runs dry, check

the action of the Pump and the Water level of the Tub.

REV 08/04

SKU 46225 For technical questions, please call 1-800-444-3353. Page 8

Maintenance

Always unplug the Power Cord before servicing and before performing any

maintenance.

General Maintenance:

1. Regularly inspect the Diamond Saw Blade. Using a dull Blade will cause

excessive wear on the Motor, and will not produce a satisfactory cut. Replace

with a new one when needed.

5. If the Motor stops suddenly, flip the Power Switch to the “off” position. Wait

approximately 15 minutes, remove the Circuit Breaker Cap located directly

above the Power Switch, and push the Reset Button.

Using the Parallel Guide:

If you have to cut a number of tiles to the same dimension, using the Parallel Guide

may save you a significant amount of time.

1. Mark the first tile to the correct dimensions, allowing space for grout.

2. With the Motor turned off, place the marked tile on the Table against the Fence.

Align the cut mark with the Blade.

3. Loosen the Locking Knob [23] on the Parallel Guide [57]. Place the hooked

portion of the Guide over the upturned edge of the Table, on the side of the

cutting groove where you have placed the part of the marked tile that you

intend to keep and use after cutting. The Parallel Guide will be parallel to the

tile, and perpendicular to the Fence.

4. Slide the Parallel Guide along the Fence until it abuts the tile, keeping sure that

the mark on your tile remains in line with the Blade.

5. Tighten the Locking Knob on the Parallel Guide.

6. When you are satisfied that the tile is aligned with the Blade, and the Guide is

in place, and it is safe to do so, turn on the Power Switch. Cut the tile as described

in previous instructions.

7. Check to be sure that the tile has been cut to the proper dimensions before

using the Parallel Guide to cut your other tiles. Periodically test the fit of each

tile as you continue cutting, to be sure the Parallel Guide has not moved.

Using the Angle Guide:

Use the Angle Guide for cutting angled edges on your tiles.

1. Attach the Angle Guide [58] to the Fence as you did the Parallel Guide, using

the two Locking Knobs [23] to hold the Guide in place.

2. Use the Cutting Groove in the middle of the Table to brace the edge of your tile

as you slide the tile and the Table underneath the Blade.

SKU 46225 For technical questions, please call 1-800-444-3353. Page 9

PLEASE READ THE FOLLOWING CAREFULLY

THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS DIA-

GRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER

NOR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO

THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT

OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN

FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY STATES THAT ALL

REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND

LICENSED TECHNICIANS AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK

AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR

REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF

REPLACEMENT PARTS THERETO.

2. Inspect the Mounting Screws on all safety covers, and the Arbor Nut on the

Cutting Wheel Shaft. Tighten any that appear loose.

3. Protect the Motor and electrical components from prolonged or excessive

exposure to water or wet conditions. Wipe the unit dry as needed.

4. Periodically apply a light lubricant to the Rail Cover.

5. Note: The Pump is non-serviceable. If it should fail, first try clearing the intake

of debris and be sure the hole is not plugged.

6. To clean the Pump Filter, remove the front cover and impeller. See Figure A.

7. Ue a small brush or stream of water to remove any debris.

8. If the Pump is used on a dirty surface, raise it slightly to reduce the amount of

debris entering the intake.

9. Adjust the Flow Control on the end of the Pump to restrict flow.

10. Do not let the Pump run when it is not submerged in water. Running the Pump

out of the water will damage the Pump.

11. If the Pump still does not work, it must be replaced. Replacement Pumps are

available through Harbor Freight Tools.

REV 08/06

Figure A

SKU 46225 For technical questions, please call 1-800-444-3353. Page 10

Parts List

Item Description QTY Item

1 Water tank 1

2 Plastic block 1

3 Bolt 2

4 Flat washer 2

5 Teeth washer 2

6 Machine frame 1

7 Bolt 2

8 Elastic washer 2

9 Big flat washer 2

10 Screw 1

11 Locking knob 1

12 Supporting frame 1

13 Shaft 1

14 Tension adjust plate 1

15 Flat washer 1

16 Bolt 1

17 Motor wheel 1

20 Blade guard 1

REV 03/05, 08/06

20a Brass tube 2

21 Water baffle 1

21a Screw 1

22 Water Connector 1

23 Locking knob 4

24 Flat washer 6

25 Brake holder 1

26 Brake shaft 1

27 E-ring 1

28 Spring 1

29 Nut 1

30 Outer flange 1

31 Blade (shipment w/o blade) 1

32 Inner flange 1

33 Rubber block 1

34 Machine bed 1

35 Bolt 4

36 Wheel cover 1

37 Screw 3

38 Belt 1

18 Screw

19 Motor

Screw 3

Fig. 1

Tile Saw with Table Stand,

SKU #46310, available for purchase

from Harbor Freight Tool Company.

Description QTY

Inhaltsverzeichnis

Andere Chicago Electric Gesehen Handbücher

Chicago Electric

Chicago Electric 42624 Bedienungsanleitung

Chicago Electric

Chicago Electric 8897 Bedienungsanleitung

Chicago Electric

Chicago Electric 91938 Bedienungsanleitung

Chicago Electric

Chicago Electric 38941 Stücklistenhandbuch

Chicago Electric

Chicago Electric 61971 Montageanleitung

Chicago Electric

Chicago Electric 69067 Montageanleitung

Chicago Electric

Chicago Electric 65570 Montageanleitung

Chicago Electric

Chicago Electric 41453 Betriebsanleitung

Chicago Electric

Chicago Electric 98265 Bedienungsanleitung

Chicago Electric

Chicago Electric 47003 Bedienungsanleitung

Chicago Electric

Chicago Electric 92386 Stücklistenhandbuch

Chicago Electric

Chicago Electric 91935 Bedienungsanleitung

Chicago Electric

Chicago Electric 69078 Bedienungsanleitung

Chicago Electric

Chicago Electric 61971 Montageanleitung

Chicago Electric

Chicago Electric 47840 Montageanleitung

Chicago Electric

Chicago Electric 62800 Montageanleitung

Chicago Electric

Chicago Electric 36595 Bedienungsanleitung

Chicago Electric

Chicago Electric 91757 Bedienungsanleitung

Chicago Electric

Chicago Electric 65766 Bedienungsanleitung

Chicago Electric

Chicago Electric 98265 Installationshandbuch

Chicago Electric

Chicago Electric 66660 Installationshandbuch

Chicago Electric

Chicago Electric 46737 Bedienungsanleitung

Chicago Electric

Chicago Electric 62370 Montageanleitung

Chicago Electric

Chicago Electric 41903 Kurzanleitung

Beliebte Gesehen Handbücher anderer Marken

RIDGID

RIDGID BS1400 Bedienungsanleitung

ATIKA

ATIKA BWS 400-2 Bedienungsanleitung

RGC

RGC FS20 Bedienungsanleitung

Makita

Makita M2300 Bedienungsanleitung

IMET Spa

IMET Spa BASIC 300 PLUS SHI Bedienungsanleitung

IMET Spa

IMET Spa SIRIO 370 AF-E Bedienungsanleitung

Optimum

Optimum OPTisaw CS 275 Bedienungsanleitung

Makita

Makita BPB180 Bedienungsanleitung

Stihl

Stihl MS 462 C-M Bedienungsanleitung

AEG

AEG TS 250 K Bedienungsanleitung

Meec tools

Meec tools 004665 Bedienungsanleitung

Makita

Makita LS1018L Bedienungsanleitung

Ryobi

Ryobi RCS1400 Bedienungsanleitung

DeWalt

DeWalt DCS391 Bedienungsanleitung

Sealey

Sealey SA72 Bedienungsanleitung

skilsaw

skilsaw SPT88 Montageanleitung

Urrea

Urrea SI810 Abmessungen und Installationsanleitung

EINHELL

EINHELL BKG 210/1 Bedienungsanleitung