Cisco 12000 - Series Chassis Modular Expansion... Bedienungs- und Wartungsanleitung

Americas Headquarters:

Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA 95134-1706 USA

ATM Line Card Installation and Configuration

This hardware installation and configuration note contains instructions for installing, configuring, and

troubleshooting Asynchronous Transfer Mode (ATM) line cards on supported Cisco 12000 series

routers.

Contents

This installation and configuration note includes the following sections:

•Important Information, page 1

•Product Overviews, page 4

•Preparing for Installation, page 7

•Removing and Installing a Line Card, page 8

•Line Card Cable-Management Bracket, page 17

•Cabling and Specifications, page 22

•Verifying and Troubleshooting Line Card Installation, page 26

•Configuring and Troubleshooting Interfaces, page 32

•Line Card Memory, page 43

•Regulatory, Compliance, and Safety Information, page 59

•Obtaining Documentation, page 62

Important Information

This section contains important information about the following:

•ATM Line Card Product Numbers, page 2

•Router Hardware Installation, page 2

•Cisco IOS Software Release Requirements, page 2

ATM Line Card Installation and Configuration

OL-13004-01

Important Information

•Hardware Revision Requirements, page 3

•Related Documentation, page 4

ATM Line Card Product Numbers

Table 1 lists the Cisco product numbers to which this publication applies.

Router Hardware Installation

For hardware installation and configuration information for Cisco 12000 series routers, refer to the

installation and configuration guide for your router. The guide includes information on the router switch

fabric and its affect on operation of the line card, as well as line card slot locations and other

requirements.

Supported Platforms

The ATM line card is supported on all Cisco 12000 series routers.

Note The installation procedure of the 4-port ISE ATM line card in the Cisco 12008 and Cisco 12012 Routers

is slightly different than that for other routers in the series. Take note of the differences in the installation

sections.

Cisco IOS Software Release Requirements

For software configuration information, refer to the Cisco IOS software configuration and command

reference publications for the installed Cisco IOS software release. Also, refer to the Cisco IOS software

release notes for additional information.

Table 1 ATM Line Card Product Numbers

ATM Line Card Cisco Product Number

1-port OC-12c/STM-4c multimode LC-1OC12/ATM-MM=

1-port OC-12c/STM-4c single-mode LC-1OC12/ATM-SM=

4-port OC-3c/STM-1 multimode 4OC3/ATM-MM-SC=

4-port OC-3c/STM-1 intermediate-reach 4OC3/ATM-IR-SC=

4-port OC-12c/STM-4c multimode 4OC12/ATM-MM-SC=

4-port OC-12c/STM-4c intermediate-reach 4OC12/ATM-IR-SC=

8-port OC-3c/STM-1 multimode 8OC03/ATM/TS-MM=

8-port OC-3c/STM-1 intermediate-reach 8OC03/ATM/TS-IR=

4-port OC-3c/STM-1 ISE multimode 4OC3X/ATM-MM-SC=

4-port OC-3c/STM-1 ISE intermediate-reach 4OC3X/ATM-IR-SC=

4-port OC-12c/STM-4c ISE multimode 4OC12X/ATM-MM-SC=

4-port OC-12c/STM-4c ISE intermediate-reach 4OC12X/ATM-IR-SC=

ATM Line Card Installation and Configuration

OL-13004-01

Important Information

Table 2 lists the Cisco IOS releases and other software components that are compatible with the various

ATM line cards.

The show version and show hardware commands display the current hardware configuration of the

router, including the system software version that is currently loaded and running. For complete

descriptions of show commands, refer to the Cisco IOS Configuration Fundamentals Configuration

Guide and the Cisco IOS Configuration Fundamentals Command Reference for the installed Cisco IOS

Release and see the “Using show Commands to Check Status” section on page 34.

Hardware Revision Requirements

To ensure compatibility with the software, your ATM line card should have a specific hardware revision

number. This number is printed on a label affixed to the component side of the card. The hardware

revision number can also be displayed using the show version command.

Table 3 lists the hardware revision numbers for all ATM line cards.

Table 2 ATM Line Card and Software Component Compatibility

ATM Line Card Compatible Cisco IOS Release

1-port OC-12c/STM-4c 11.2(9) or later

4-port OC-3c/STM-1 11.2(4)GS1 or later

4-port OC-12c/STM-4c 12.0(13)S or later 12.0 S release

8-port OC-3c/STM-1 12.0(22)S or a later 12.0 S release

4-port OC-3c/STM-1 ISE 12.0(26)S2, 12.0(27)S1 or a later 12.0 S release

4-port OC-12c/STM-4c ISE 12.0(25)S or a later 12.0 S release

Table 3 ATM Line Card Hardware Revision Numbers

ATM Line Card Hardware Revision Number1

1. Hardware revision numbers that are higher than those listed are also compatible. These are the minimum

required numbers.

1-port OC-12c/STM-4c 73-2526-04 rev. A0 for multimode

73-2525-04 rev A0 for single-mode

4-port OC-3c/STM-1 78-3034-02 rev. A0 for multimode

73-3033-02 rev. A0 for single-mode

4-port OC-12c/STM-4c 800-05669-02 rev. A0, 73-3983-05 rev. A0 for multimode

800-05606-02 rev. A0, 73-3984-05 rev. A0 for single-mode

8-port OC-3c/STM-1 73-7919-02 for multimode

73-7920-02 for single-mode

4-port OC-3c/STM-1 ISE 800-24352-01 for multimode

800-24341-01 for single-mode

4-port OC-12c/STM-4c ISE 800-20757-01 for multimode

800-20368-01 for single-mode

ATM Line Card Installation and Configuration

OL-13004-01

Product Overviews

Related Documentation

This publication describes the basic installation and configuration of a ATM line card. For complete

software and ATM configuration information, refer to the following publications:

•Cisco 12000 Series Router Installation and Configuration Guides

•Cisco 12000 Series Internet Router Configuration Guide for Cisco IOS Release 12.0S

•Cisco IOS Configuration Fundamentals Configuration Guide

•Cisco IOS Configuration Fundamentals Command Reference

•Cisco IOS Release 12.0S Release Notes for Cisco 12000 Series Routers

•4-Port ATM ISE Line Card Feature Module

•Regulatory Compliance and Safety Information for Cisco 12000 Series Internet Routers

See the “Obtaining Documentation” section on page 62 for information on how to obtain these

publications.

Product Overviews

This section includes product overview information for each ATM line card:

•1-port OC-12c/STM-4c ATM Line Card Overview, page 4

•4-port OC-3c/STM-1 ATM Line Card Overview, page 5

•4-port OC-12c/STM-4c ATM Line Card Overview, page 5

•8-port OC-3c/STM-1 ATM Line Card Overview, page 6

•4-port OC-12c/STM-4c ISE and 4-port OC-3c/STM-1 ISE ATM Line Card Overview, page 6

1-port OC-12c/STM-4c ATM Line Card Overview

The 1-port OC-12c/STM-4c ATM line card provides the Cisco 12000 series router with one 622-Mbps

ATM interface. The card interfaces to the router’s switch fabric and provides one OC-12c/STM-4c

duplex SC single-mode or multimode SONET/SDH connection. This connection is concatenated, which

provides for increased efficiency by eliminating the need to partition the bandwidth.

Figure 1 illustrates the single-mode, intermediate-range 1-port OC-12c/STM-4c ATM line card.

Figure 1 1-port OC-12c/STM-4c ATM Line Card—Single-Mode

1Ejector lever 3Status LEDs

2Port 0 4Display LEDs

OC-12/STM-4 SM IR ATM

ACTIVE

CARRIER

RX CELL

123 4

101924

ATM Line Card Installation and Configuration

OL-13004-01

Product Overviews

4-port OC-3c/STM-1 ATM Line Card Overview

The 4-port OC-3c/STM-1 ATM line card interfaces with the switch fabric of the Cisco 12000 Series

Router. It provides four 155-Mbps OC-3c/STM-1c duplex SC single-mode or multimode SONET/SDH

connections. This connection is concatenated, which provides for increased efficiency by eliminating the

need to partition the bandwidth.

Figure 2 shows the single-mode, intermediate-range 4-port OC-3c/STM-1 ATM line card.

Figure 2 4-port OC-3c/STM-1 ATM Line Card

4-port OC-12c/STM-4c ATM Line Card Overview

The 4-port OC-12c/STM-4c ATM line card provides the Cisco 12000 Series Router with four 622-Mbps

ATM interfaces. The card interfaces to the router’s switch fabric and provides four OC-12c/STM-4c SC

connectors for duplex single-mode or multimode SONET/SDH connections.

Figure 3 illustrates the single-mode, intermediate-range 4-port OC-12c/STM-4c ATM line card. There

are four ports, numbered 0 to 3, on each line card. Each port has a set of status LEDs. Each SONET

connection is concatenated, which provides for increased efficiency by eliminating the need to partition

the bandwidth.

Figure 3 4-port OC-12c/STM-4c ATM Line Card—Intermediate-Range

1Ejector lever 3Status LEDs

2Port 0 4Display LEDs

ACTIVE

CARRIER

RX PKT

ACTIVE

CARRIER

RX PKT

ACTIVE

CARRIER

RX PKT

ACTIVE

CARRIER

RX PKT

Q OC-3/STM-1 SM IR POS

123 4

101925

1Ejector lever 3Status LEDs

2Port 0 4Display LEDs

101923

ACTIVE

CARRIER

RX CELL

OC-12/STM-4 SM-SC ATM

ACTIVE

CARRIER

RX CELL

ACTIVE

CARRIER

RX CELL

ACTIVE

CARRIER

RX CELL

23 3

ATM Line Card Installation and Configuration

OL-13004-01

Product Overviews

8-port OC-3c/STM-1 ATM Line Card Overview

The 8-port OC-3c/STM-1 ATM line card supports traffic shaping, and delivers line rate OC-3c/STM-1

bandwidth while performing traffic shaping and per-virtual circuit (VC) queueing. It also supports

per-VC Modified Deficit Round Robin (MDRR) and per-VC low latency queueing (LLQ).

MDRR is implemented on a per-VC basis, with up to eight queues per VC. One of the queues is a low

latency queue. Both per-VC WRED and per-VC MDRR are performed in hardware.

The 8-port OC-3c/STM-1 ATM line card provides the Cisco 12000 Series Router with eight 155 Mbps

ATM interfaces. The card interfaces to the router’s switch fabric and provides eight OC-3c/STM-1 SC

connectors for duplex single-mode or multimode SONET/SDH connections.

Figure 4 shows the single-mode, intermediate-range 8-port OC-3c/STM-1 ATM line card.

Figure 4 8-port OC-3c/STM-1 ATM Line Card

4-port OC-12c/STM-4c ISE and 4-port OC-3c/STM-1 ISE ATM Line Card

Overview

The 4-port ISE ATM line cards provide the Cisco 12000 series routers with an ATM line card that offers

the IP services engine or Engine 3 features, including extensive traffic queuing, shaping, and congestion

management features, at a sustained full duplex throughput of 5.66 million cells per second (4-port

OC-12c/STM-4c ISE ATM line card) or 1.41 million cells per second (4-port OC-3c/STM-1 ISE ATM

line card). The 4-port ISE ATM line card is available with either OC-12c/STM-4c or OC-3c/STM-1

interfaces. Except for the speed of the interfaces, these line cards provide identical functionality, and are

referred to throughout this document as the 4-port ISE ATM line cards.

The 4-port ISE ATM line card delivers a robust set of edge packet processing features such as ACL,

ExACL, CAR, NetFlow, and Multicast with incorporated MDRR, WRED and backpressure congestion

avoidance mechanism. This line card brings enhanced Layer 3 processing and high bandwidth ATM

capabilities to the Cisco 12000 series router.

In addition, the 4-port ISE ATM line cards provide Layer 2 AToM tunneling with cell relay and cell

packing on VCs, VPs, and interfaces; ATM traffic shaping and policing; and Layer 2 and Layer 3

configurations on the same port.

The line cards consist of two boards: a generic IP services engine motherboard that contains the Engine 3

chip set and fabric interface and a physical layer interface module (PLIM)-specific card providing the

four optic interfaces.

1Ejector lever 3Status LEDs

2Port 0 4Display LEDs

PRODUCTO LASER CLASE 1

PRODUIT LASER DE CLASSE 1

CLASS 1 LASER PRODUCT

LASERPRODUKT DER KLASSE 1

ACTIVE

CARRIER

RX CELL

8OC-3/STM-1 ATM/TS IR-SC

123 4

101926

ATM Line Card Installation and Configuration

OL-13004-01

Preparing for Installation

Figure 5 shows the front view of the 4-port ISE ATM line card.

Figure 5 4-port ISE ATM Line Card

Preparing for Installation

Before you begin the installation process, review the important information in the following sections:

•Safety Guidelines, page 7

•Preventing Electrostatic Discharge, page 8

•Required Tools and Equipment, page 8

Safety Guidelines

Before you perform any procedure in this publication, review the safety guidelines in this section to

avoid injuring yourself or damaging the equipment.

The following guidelines are for your safety and to protect equipment. The guidelines do not include all

hazards. Be alert.

Note Review the safety warnings listed in the Regulatory Compliance and Safety Information for

Cisco 12000 Series Internet Router publication (Document Number 78-4347-xx) that accompanied your

router before installing, configuring, or maintaining a line card.

•Keep the work area clear and dust free during and after installation. Do not allow dirt or debris to

enter into any laser-based components.

•Do not wear loose clothing, jewelry, or other items that could get caught in the router while working

with line cards.

•Cisco equipment operates safely when it is used in accordance with its specifications and product

usage instructions.

1Ejector lever 3Status LEDs

2Port 0 4Display LEDs

4OC12X/ATM-MM-SC

LED DENOTATION

CARRIER

RX CELL

ACTIVE

CLEAN

CONNECTOR

WITH ALCOHOL

WIPES BEFORE

CONNECTING

84923

Cisco Systems, Inc.

170 W Tasman Drive

San Jose, Ca 95134

Manufactured

xxxxxxxx xxxx:

Complies with 21 CFR

Chapter 1, Subchapter J

CNS68V4AAA

ATM Line Card Installation and Configuration

OL-13004-01

Removing and Installing a Line Card

Preventing Electrostatic Discharge

Electrostatic discharge (ESD) damage, which can occur when electronic cards or components are

improperly handled, results in complete or intermittent failures. Electromagnetic interference (EMI)

shielding is an integral component of the line card. Cisco recommends using an ESD-preventive strap

whenever you are handling network equipment or one of its components.

The following are guidelines for preventing ESD damage:

•Always use an ESD-preventive wrist or ankle strap and ensure that it makes good skin contact.

Connect the equipment end of the connection cord to an ESD connection socket on the router or to

bare metal on the chassis.

•Handle ATM line cards by the captive installation screws, the provided handle, ejector levers, or the

line card metal carrier only; avoid touching the board or connector pins.

•Place removed ATM line cards board-side-up on an antistatic surface or in a static shielding bag. If

you plan to return the component to the factory, immediately place it in a static shielding bag.

•Avoid contact between the ATM line cards and clothing. The wrist strap only protects the board from

ESD voltages on the body; ESD voltages on clothing can still cause damage.

Warning

For safety, periodically check the resistance value of the ESD strap. The measurement should be

between 1 and 10 megohms.

Required Tools and Equipment

You need the following tools and parts to remove and install ATM line cards:

•Flat-blade or Phillips screwdriver

•ESD-preventive wrist or ankle strap and instructions

•Interface cables to connect the ATM line card with another router or switch

See the “Fiber-Optic Network Interface Cables” section on page 24 for cable details.

Removing and Installing a Line Card

This section describes the procedures for removing and installing a line card and includes the following

sections:

•Guidelines for Line Card Removal and Installation, page 9

•Removing a Line Card, page 10

•Removing the Blank Filler, page 12

•Installing a Blank Filler, page 12

•Installing a Line Card, page 14

ATM Line Card Installation and Configuration

OL-13004-01

Removing and Installing a Line Card

Note The installation and removal procedure for the ATM line card is different for the Cisco 12008 and

Cisco 12012 routers than for the other Cisco 12000 series routers. Make sure you refer to the

procedure that corresponds to your router chassis.

Caution To avoid erroneous failure messages, remove or insert only one line card at a time. After inserting or

removing a line card, allow at least 15 seconds before removing or inserting another line card, so that

the router can reinitialize and note the current configuration of all interfaces.

After removing and inserting a line card into the same slot, allow at least 60 seconds before removing

or inserting another line card.

Guidelines for Line Card Removal and Installation

Guidelines for line card removal and installation include the following:

•Online insertion and removal (OIR) is supported, enabling you to remove and install line cards while

the router is operating. OIR is seamless to users on the network, maintains all routing information,

and ensures session preservation.

Note With OIR, notifying the software or resetting the power is not required. However, you have the

option of using the shutdown command before removing a line card.

•After you reinstall a line card, the router automatically downloads the necessary software from the

route processor (RP). Next, the router brings online only those interfaces that match the current

configuration and were previously configured as administratively up. You must configure all others

with the configure command.

Caution The router may indicate a hardware failure if you do not follow proper procedures. Remove

or insert only one line card at a time. Allow at least 15 seconds for the router to complete the

preceding tasks before removing or inserting another line card.

After removing and inserting a line card into the same slot, allow at least 60 seconds before

removing or inserting another line card.

•Line cards have two ejector levers to release the card from its backplane connector. Use the levers

when you are removing the line card and to seat the line card firmly in its backplane connector when

you are installing the line card. The ejector levers align and seat the card connectors in the

backplane.

ATM Line Card Installation and Configuration

OL-13004-01

Removing and Installing a Line Card

Caution When you remove a line card, always use the ejector levers to ensure that the connector pins

disconnect from the backplane in the sequence expected by the router. Any card that is only

partially connected to the backplane can halt the router.

When you install a line card, always use the ejector levers to ensure that the card is correctly

aligned with the backplane connector; the connector pins should make contact with the

backplane in the correct order, indicating that the card is fully seated in the backplane. If a

card is only partially seated in the backplane, the router will hang and subsequently crash.

•The 4-port ISE ATM line card requires two slots when installed into a Cisco 12008 or Cisco 12012

Router. Before installing the line card, you must install the blank filler (part number:

4OC12X/ATM-BLANK) into the rightmost of the two slots. For detailed instructions, see the

“Installing a Blank Filler” section on page 12.

For line card configuration information, see the “Configuring and Troubleshooting Interfaces” section

on page 32.

Removing a Line Card

If you are replacing a failed line card, remove the existing line card first, then install the new line card

in the same slot. To remove a line card, use Figure 6 as a reference and follow these steps:

Step 1 Attach an ESD-preventive wrist or ankle strap and follow its instructions for use.

Step 2 Disconnect and remove all interface cables from the ports; note the current connections of the cables to

the ports on the line card.

Step 3 Detach the line card cable-management bracket from the line card.

Step 4 Use a screwdriver to loosen the captive screw at each end of the line card faceplate. (See Figure 6a.)

Andere Handbücher für 12000 - Series Chassis Modular Expansion...

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Cisco Netzwerkkarte Handbücher

Cisco

Cisco WPC600N - Ultra RangePlus Wireless-N PC Card Bedienungsanleitung

Cisco

Cisco Gateway Controllers Originalbetriebsanleitung

Cisco

Cisco Catalyst 4500 Series Anleitung zur Verwendung

Cisco

Cisco Media Gateway Controller Node Manager Bedienungsanleitung

Cisco

Cisco PA-FE-FX Bedienerhandbuch

Cisco

Cisco 7300-6T3 Bedienerhandbuch

Cisco

Cisco EHWIC 1 GE-SFP-CU Bedienungsanleitung

Cisco

Cisco Catalyst 4500 Series Handbuch

Cisco

Cisco CE-100T-8 Bedienungsanleitung

Cisco

Cisco WAN Interface Card Cable WIC-1DSU-T1 Bedienungsanleitung

Cisco

Cisco PA-4C-E 1 Bedienerhandbuch

Cisco

Cisco uBR10-MC5X20H Bedienungsanleitung

Cisco

Cisco EHWIC-4SHDSL-EA Merkblatt

Cisco

Cisco NPE-175 Bedienerhandbuch

Cisco

Cisco WAN Interface Cards Cable WIC-1B-U Bedienungsanleitung

Cisco

Cisco MC16E Bedienungsanleitung

Cisco

Cisco CTX2500 Bedienungsanleitung

Cisco

Cisco Modular Gigabit Ethernet Line Card I Bedienungs- und Wartungsanleitung

Cisco

Cisco MGX-FRSM-2CT3 Bedienungsanleitung

Cisco

Cisco Linksys WUSB600N Bedienungsanleitung

Cisco

Cisco ASR 9000 Series Bedienungsanleitung

Cisco

Cisco WEC600N Bedienungsanleitung

Cisco

Cisco IDTA153 Bedienungsanleitung

Cisco

Cisco HWIC-4ESW - EtherSwitch HWIC Switch Bedienungsanleitung

Beliebte Netzwerkkarte Handbücher anderer Marken

FirstComm

FirstComm OBiWiFi5G Bedienungsanleitung

Sun Microsystems

Sun Microsystems Interface Adapter Bedienungsanleitung

TRENDnet

TRENDnet TU2-ETG Bedienungsanleitung

YASKAWA

YASKAWA SI-EN3 Bedienungsanleitung

Paradyne

Paradyne BitStorm 2600 IP DSLAM Bedienungsanleitung

Belkin

Belkin F5D7050 Bedienungsanleitung

3Com

3Com EtherLink 3C509B Bedienungsanleitung

TRENDnet

TRENDnet TEG-PCITX Bedienungsanleitung

Delta Electronics

Delta Electronics Braking Modules VFDB Series Bedienungsanleitung

TwinMOS

TwinMOS Booming Bedienungsanleitung

Dialogic

Dialogic Media Board DM/V1200BTEPEQ Bedienungsanleitung

Buffalo

Buffalo AirStation WLI-PCM-L11GP Bedienungsanleitung

National Instruments

National Instruments NI 9234 Bedienungsanleitung

Bose

Bose PowerMatch Dante Bedienungsanleitung

Compaq

Compaq Wireless LAN 100 Bedienungsanleitung

TRENDnet

TRENDnet TEG-PCITXR Bedienungsanleitung

Gigafast

Gigafast EE101-AEX Bedienungsanleitung

D-Link

D-Link DHP?P309AV Bedienungsanleitung