Cisco Gigabit Switch Router Cisco 12012 Leitfaden

Doc. No.

Cisco Systems, Inc.

170 West Tasman Drive

San Jose, CA 95134-1706

USA

Cisco Systems, Inc.

Corporate Headquarters

Cisco 12012 Gigabit Switch Router Card Cage

Assembly Replacement Instructions

Product Number: GSR12-CARDCAGE=

This document contains instructions for removing and replacing a card cage assembly in the

Cisco 12012 Gigabit Switch Router (GSR).

The sections in this document include the following:

•Product Overview, page 1

•Safety Guidelines, page 3

•Tools and Parts Required, page 6

•Removing and Replacing a Card Cage Assembly, page 7

•FCC Class A Compliance, page 32

•Cisco Connection Online, page 33

Product Overview

The Cisco 12012 has two card cages; the upper card cage and the lower card cage. (Refer to

Figure 1.) The upper card cage has 12 user-configurable slots available for line cards and a route

processor (RP). One additional slot (rightmost slot) in the upper card cage is non-configurable; it is

reserved for an alarm card. The line cards and the RP are not slot dependent; you can install the line

cards and the RP in any of the first 12 available slots.

78-4337-02

2Cisco 12012 Gigabit Switch Router Card Cage Assembly Replacement Instructions

Product Overview

Figure 1 Cisco 12012—Front View

The lower card cage, located behind the air filter, has five keyed horizontal slots for cards containing

the switch fabric circuitry. The cards provide the physical pathway for data packet exchange between

the line cards in the upper card cage.

There are two types of cards installed in the lower card cage; the clock and scheduler card (CSC)

and the switch fabric card (SFC). Both types of cards are keyed to fit into specific slots in the lower

card cage. You can install the clock and scheduler card only in the top two slots and the switch fabric

card only in the lower three slots. The clock and scheduler card contains the system clock, switch

fabric scheduler circuitry, and the switch fabric. The switch fabric card contains only switch fabric

circuitry.

Below the lower card cage is a power supply bay. The Cisco 12012 can be configured for source AC

or source DC operation. A system configured for source AC operation must have a minimum of two

AC-input power supplies installed. You can install two additional AC-input power supplies for

redundancy and current sharing. Systems configured for source DC operation have one DC-input

power supply installed. You can install a second DC-input power supply for redundancy and current

sharing.

The Cisco 12012 has two blower modules; one located above the upper card cage and one located

below the power supply bay. They draw filtered cooling air in through both card cages and the power

supply bay to maintain acceptable operating temperatures for the internal components.

INPUT:

200-240V

10A

50/60HZ

2000W

OUTPUT

FAIL

INPUT:

200-240V

10A

50/60HZ

2000W

OUTPUT

FAIL

INPUT:

200-240V

10A

50/60HZ

2000W

OUTPUT

FAIL

INPUT:

200-240V

10A

50/60HZ

2000W

OUTPUT

FAIL

SLOT

-0

ROUTEPROCESSOR

SLOT

-1

COLL

LINK

RJ-45

MII

RESET

AUX

CONSOLE

EJECT

ACTIVE

CARRIER

RXPKT

ACTIVE

CARRIER

RXPKT

ACTIVE

CARRIER

RXPKT

ACTIVE

CARRIER

RXPKT

QOC-3/STM-POS

ACTIVE

CARRIER

RXCELL

OC-12/STM-4ATM

OC-12/STM-4POS

ACTIVE

CARRIER

RXCELL

ACO/LT

ALARM

CSC

FAIL

ENABLED

CRITICAL

MAJOR

MINOR

SFC

ALARM1 ALARM2

H10476

Top blower module

(behind front cover)

Upper card cage

Lower card cage

(behind air filter)

Frame

Air filter tray

Power supply bay

Bottom blower module

(behind front cover)

Cisco 12012 Gigabit Switch Router Card Cage Assembly Replacement Instructions 3

Safety Guidelines

Before you begin the replacement procedure, review the safety guidelines in this section to avoid

injuring yourself or damaging the equipment. This section also repeats in multiple languages the

warnings in this document.

In addition, review the safety warnings listed in the document Regulatory Compliance and Safety

Information for the Cisco 12012 Gigabit Switch Router (Document Number 78-4347-xx) that

supports your Cisco 12012 before installing, configuring, or maintaining the router.

Following are translations for the warning statements used in this document.

Safety Warnings

Warning This warning symbol means danger. You are in a situation that could cause bodily injury.

Before you work on any equipment, be aware of the hazards involved with electrical circuitry and

be familiar with standard practices for preventing accidents. To see translations of the warnings that

appear in this publication, refer to the Regulatory Compliance and Safety Information document that

accompanied this device.

Waarschuwing Dit waarschuwingssymbool betekent gevaar. U verkeert in een situatie die

lichamelijk letsel kan veroorzaken. Voordat u aan enige apparatuur gaat werken, dient u zich bewust

te zijn van de bij elektrische schakelingen betrokken risico's en dient u op de hoogte te zijn van

standaard maatregelen om ongelukken te voorkomen. Voor vertalingen van de waarschuwingen die

in deze publicatie verschijnen, kunt u het document Regulatory Compliance and Safety Information

(Informatie over naleving van veiligheids- en andere voorschriften) raadplegen dat bij dit toestel is

ingesloten.

Varoitus Tämä varoitusmerkki merkitsee vaaraa. Olet tilanteessa, joka voi johtaa ruumiinvammaan.

Ennen kuin työskentelet minkään laitteiston parissa, ota selvää sähkökytkentöihin liittyvistä

vaaroista ja tavanomaisista onnettomuuksien ehkäisykeinoista. Tässä julkaisussa esiintyvien

varoitusten käännökset löydät laitteen mukana olevasta Regulatory Compliance and Safety

Information -kirjasesta (määräysten noudattaminen ja tietoa turvallisuudesta).

Attention Ce symbole d'avertissement indique un danger. Vous vous trouvez dans une situation

pouvant causer des blessures ou des dommages corporels. Avant de travailler sur un équipement,

soyez conscient des dangers posés par les circuits électriques et familiarisez-vous avec les

procédures couramment utilisées pour éviter les accidents. Pour prendre connaissance des

traductions d’avertissements figurant dans cette publication, consultez le document Regulatory

Compliance and Safety Information (Conformité aux règlements et consignes de sécurité) qui

accompagne cet appareil.

4Cisco 12012 Gigabit Switch Router Card Cage Assembly Replacement Instructions

Safety Guidelines

Warnung Dieses Warnsymbol bedeutet Gefahr. Sie befinden sich in einer Situation, die zu einer

Körperverletzung führen könnte. Bevor Sie mit der Arbeit an irgendeinem Gerät beginnen, seien Sie

sich der mit elektrischen Stromkreisen verbundenen Gefahren und der Standardpraktiken zur

Vermeidung von Unfällen bewußt. Übersetzungen der in dieser Veröffentlichung enthaltenen

Warnhinweise finden Sie im Dokument Regulatory Compliance and Safety Information

(Informationen zu behördlichen Vorschriften und Sicherheit), das zusammen mit diesem Gerät

geliefert wurde.

Avvertenza Questo simbolo di avvertenza indica un pericolo. La situazione potrebbe causare

infortuni alle persone. Prima di lavorare su qualsiasi apparecchiatura, occorre conoscere i pericoli

relativi ai circuiti elettrici ed essere al corrente delle pratiche standard per la prevenzione di incidenti.

La traduzione delle avvertenze riportate in questa pubblicazione si trova nel documento Regulatory

Compliance and Safety Information (Conformità alle norme e informazioni sulla sicurezza) che

accompagna questo dispositivo.

Advarsel Dette varselsymbolet betyr fare. Du befinner deg i en situasjon som kan føre til

personskade. Før du utfører arbeid på utstyr, må du vare oppmerksom på de faremomentene som

elektriske kretser innebærer, samt gjøre deg kjent med vanlig praksis når det gjelder å unngå ulykker.

Hvis du vil se oversettelser av de advarslene som finnes i denne publikasjonen, kan du se i

dokumentet Regulatory Compliance and Safety Information (Overholdelse av forskrifter og

sikkerhetsinformasjon) som ble levert med denne enheten.

Aviso Este símbolo de aviso indica perigo. Encontra-se numa situação que lhe poderá causar danos

físicos. Antes de começar a trabalhar com qualquer equipamento, familiarize-se com os perigos

relacionados com circuitos eléctricos, e com quaisquer práticas comuns que possam prevenir

possíveis acidentes. Para ver as traduções dos avisos que constam desta publicação, consulte o

documento Regulatory Compliance and Safety Information (Informação de Segurança e Disposições

Reguladoras) que acompanha este dispositivo.

¡Advertencia! Este símbolo de aviso significa peligro. Existe riesgo para su integridad física.

Antes de manipular cualquier equipo, considerar los riesgos que entraña la corriente eléctrica y

familiarizarse con los procedimientos estándar de prevención de accidentes. Para ver una traducción

de las advertencias que aparecen en esta publicación, consultar el documento titulado Regulatory

Compliance and Safety Information (Información sobre seguridad y conformidad con las

disposiciones reglamentarias) que se acompaña con este dispositivo.

Varning! Denna varningssymbol signalerar fara. Du befinner dig i en situation som kan leda till

personskada. Innan du utför arbete på någon utrustning måste du vara medveten om farorna med

elkretsar och känna till vanligt förfarande för att förebygga skador. Se förklaringar av de varningar

som förkommer i denna publikation i dokumentet Regulatory Compliance and Safety Information

(Efterrättelse av föreskrifter och säkerhetsinformation), vilket medföljer denna anordning.

Safety with Equipment

The following guidelines will help ensure your safety and protect the equipment. This list is not

inclusive of all potentially hazardous situations, so be alert.

•Always disconnect all power cords and interface cables before moving the system.

•Keep tools and assembly components away from walk areas.

•Do not work alone if potentially hazardous conditions exist.

•Do not perform any action that creates a potential hazard to people or makes the equipment

unsafe.

•Carefully examine your work area for possible hazards such as moist floors, ungrounded power

extension cables, and missing safety grounds.

Cisco 12012 Gigabit Switch Router Card Cage Assembly Replacement Instructions 5

Safety Guidelines

Safety with Electricity

The line cards, RP, switch fabric cards, blower modules, and redundant power supplies are designed

to be removed and replaced while the system is operating without presenting an electrical hazard or

damage to the system.

Follow these basic guidelines when working with any electrical equipment:

•Before beginning any procedures requiring access to the interior of the Cisco 12012, locate the

emergency power-off switch for the room in which you are working.

•Look carefully for possible hazards in your work area, such as moist floors, ungrounded power

extension cables, and missing safety grounds.

•If an electrical accident occurs, proceed as follows:

—Use caution; do not become a victim yourself. Disconnect power to the system.

—If possible, send another person to get medical aid. Otherwise, assess the condition of the

victim and then call for help.

—Determine if the person needs rescue breathing or external cardiac compressions; then take

appropriate action.

•Disconnect all power and external cables before installing or removing a router.

•Never assume that power has been disconnected from a circuit; always check.

•Do not perform any action that creates a potential hazard to people or makes the equipment

unsafe.

•Never install equipment that appears damaged.

In addition, use the guidelines that follow when working with any equipment that is disconnected

from a power source, but still connected to telephone or network wiring:

•Never install telephone wiring during a lightning storm.

•Never install telephone jacks in wet locations unless the jack is specifically designed for wet

locations.

•Never touch uninsulated telephone wires or terminals unless the telephone line has been

disconnected at the network interface.

•Use caution when installing or modifying telephone lines.

6Cisco 12012 Gigabit Switch Router Card Cage Assembly Replacement Instructions

Tools and Parts Required

Preventing Electrostatic Discharge Damage

Electrostatic discharge damage, which can occur when electronic boards or components are handled

improperly, can result in complete or intermittent failures.

Following are guidelines for preventing ESD damage:

•Always use an ESD-preventive wrist strap or ankle strap and ensure that it makes good skin

contact.

•When removing or installing a component, connect the equipment end of a ground strap to one

of the two ESD ground sockets located on the front sides of the upper card cage or to a bare metal

surface on the frame.

•If you plan to return a replaced component to the factory, immediately place it in a static shielding

bag to avoid ESD damage to the component.

•The wrist strap only protects the component from ESD voltages on the body; ESD voltages on

clothing can still cause damage.

Caution You should periodically check the resistance value of the antistatic strap. The

measurement should be between 1 and 10 megohms.

Tools and Parts Required

You need the following tools and parts to remove and replace the card cage assembly:

•ESD-preventive wrist strap

•1/4-inch flat-blade screwdriver

•3/16-inch flat-blade screwdriver

•10-mm nutdriver

•Antistatic mat

•The replacement card cage assembly (Product Number: GSR12-CARDCAGE=)

You must remove all cards and power supplies from the old card cage assembly and install them in

the replacement card cage assembly. The replacement card cage ships with a new air filter installed.

Cisco 12012 Gigabit Switch Router Card Cage Assembly Replacement Instructions 7

Removing and Replacing a Card Cage Assembly

This section covers removing and replacing of the card cage assembly. The card cage assembly

comprises a single assembly that includes the upper card cage, the lower card cage, and the power

supply bays. The assembly slides into and out of the frame and attaches to the frame with six captive

screws. An empty card cage assembly weighs 65 lb (29.5 kg). The inside dimensions of the card cage

are:

Width = 15 9/16"

Height = 14 9/16"

Depth = 17 9/16"

The replacement card cage assembly is shipped with only a new air filter; you must remove the

following components from the old card cage assembly:

•Line cards

•route processor (RP)

•Clock and scheduler cards, and switch fabric cards

•Alarm card

•Any installed card blanks

•Power supplies and power supply blanks

Store them carefully while you install the new card cage assembly in the frame, then replace the

components in the new card cage assembly.

Powering Down the Cisco 12012

Perform the following steps to power down the Cisco 12012:

Step 1 Turn the DC-input power supply power switch to the OFF (O) position (on AC-input

power supplies, turn the power switch counterclockwise to the STANDBY position) on

all power supplies installed in the Cisco 12012.

Step 2 Verify that the system has powered down by checking that the LEDs on the power

supplies are off and the green LEDs on both blower modules are off.

Warning This unit has more than one power supply connection; all connections must be removed

completely to completely remove power from the unit.

Removing a Power Supply

This section provides procedures for removing an AC-input power supply and a DC-input power

supply. Select the procedure appropriate for your system.

Caution Always wear an antistatic wrist strap to prevent ESD when removing and replacing a

power supply.

8Cisco 12012 Gigabit Switch Router Card Cage Assembly Replacement Instructions

Removing and Replacing a Card Cage Assembly

Removing an AC-Input Power Supply

Perform the following steps to remove an AC-input power supply:

Step 1 Attach an antistatic wrist strap to yourself and to one of the two ESD connection sockets

located on the front edges of the upper card cage or to bare metal on the frame.

Step 2 If you have not already done so, turn the power supply power switch to the STANDBY

position on the power supply you want to remove. (Refer to Figure 2a.)

Note Turning the power supply switch to STANDBY also releases a latch that secures

the power supply in the power supply bay slot.

Step 3 Release the spring clip on the power supply faceplate. (Refer to Figure 2b.)

Step 4 Disconnect the AC power cord from the power supply AC receptacle. (Refer to

Figure 2c.)

Step 5 Disconnect the AC power cord from the source AC receptacle. (Refer to Figure 2d.)

Step 6 Loosen the captive screw on the power supply faceplate. (Refer to Figure 2e.)

Figure 2 Disconnecting an AC-Input Power Supply

INPUT:

200 -240V ~

10 A

50/60 HZ

2000 W

OUTPUT

FAIL

Release

spring clip

Loosen

captive

screw

Disconnect

power cord

Turn power

switch to

standby

position ( )

H10375

Disconnect

power cord from

source AC

Cisco 12012 Gigabit Switch Router Card Cage Assembly Replacement Instructions 9

Removing and Replacing a Card Cage Assembly

Step 7 Grasp the power supply handle and pull straight out to disconnect the power supply from

the backplane connector. Slide the power supply halfway out of the bay slot. (Refer to

Figure 3.)

Figure 3 Removing an AC-Input Power Supply

Caution The AC-input power supply weighs 18 lb (8 kg). Use two hands when handling the power

supply.

Step 8 Place your free hand underneath the power supply for support and slide the power supply

completely out of the bay slot. Set the power supply aside

Repeat Step 2 through Step 8 for the rest of the AC-input power supplies.

Note If there are any power supply blanks installed, remove them by loosening the captive screw

on the power supply blank faceplate. Slide the power supply blank out of the power supply bay slot.

Set the power supply blank aside; you will replace the power supply blank in the replacement card

cage assembly.

OUTPUT

FAIL

INPUT:

200 -240V

10 A

50/60 HZ

2000 W

OUTPUT

FAIL

INPUT:

200 -240V

10 A

50/60 HZ

2000 W

H10376

Use two hands to slide power supply out of bay

OUTPUT

FAIL

INPUT:

200 -240V

10 A

50/60 HZ

2000 W

AC-input

power

supply

10 Cisco 12012 Gigabit Switch Router Card Cage Assembly Replacement Instructions

Removing and Replacing a Card Cage Assembly

Removing a DC-Input Power Supply

Perform the following steps to remove a DC-input power supply:

Caution Before performing any of the following procedure, ensure that power is removed from the

DC circuit. To ensure that all power is OFF, locate the circuit breaker on the panel board that services

the DC circuit, switch the circuit breaker to the OFF position, and tape the switch handle of the

circuit breaker in the OFF position.

Step 1 Attach an antistatic wrist strap to yourself and to one of the two ESD connection sockets

located on the front edges of the upper card cage or to bare metal on the frame.

Step 2 If you have not already done so, turn OFF (O) the power switch on the DC-input power

supply.

Warning Voltages might be present on the DC-input power supply terminals. Turn off the power

source circuit breaker and remove the power supply before accessing the terminals.

Note Turning the power supply switch to OFF (O) releases a latch that secures the power

supply in the power supply bay.

Step 3 Locate and turn off the source DC circuit breaker that services the power supply you want

to remove. As an added precaution, tape the circuit breaker handle in the off position.

Step 4 Using a flat-blade screwdriver or a 10-mm nutdriver, turn the captive jackscrew

counterclockwise (eject) on the power supply faceplate to unseat the power supply from

the backplane power connector. Continue turning the jackscrew to disengage the

jackscrew from the power supply bay (approximately 12 revolutions).

Step 5 Grasp the power supply handle and slide the power supply halfway out of the bay. (Refer

to Figure 4.)

Andere Handbücher für Gigabit Switch Router Cisco 12012

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Cisco Netzwerkkarte Handbücher

Cisco

Cisco WUSB54GSC Bedienungsanleitung

Cisco

Cisco PA-4C-E 1 Bedienerhandbuch

Cisco

Cisco MC16E Bedienungsanleitung

Cisco

Cisco Valet Connector AM10 Bedienungsanleitung

Cisco

Cisco Catalyst 4500 Abmessungen

Cisco

Cisco 7304 Series Bedienungs- und Wartungsanleitung

Cisco

Cisco ONS 15454 Series Bedienungsanleitung

Cisco

Cisco PA-T3 Bedienungs- und Wartungsanleitung

Cisco

Cisco DFC3B Installations- und Betriebshandbuch

Cisco

Cisco ASR 9000 Series Bedienungsanleitung

Cisco

Cisco IDTA153 Bedienungsanleitung

Cisco

Cisco Linksys USB200M Bedienungsanleitung

Cisco

Cisco WAE-674-K9 - Wide Area Application Engine... Bedienungsanleitung

Cisco

Cisco WPC600N - Ultra RangePlus Wireless-N PC Card Bedienungsanleitung

Cisco

Cisco Linksys WUSB54G Bedienungsanleitung

Cisco

Cisco WEC600N Bedienungsanleitung

Cisco

Cisco Linksys RangePlus WPC100 Bedienungsanleitung

Cisco

Cisco WAN Interface Cards Cable WIC-1B-U Bedienungsanleitung

Cisco

Cisco DFC3A Installations- und Betriebshandbuch

Cisco

Cisco HWIC-4ESW - EtherSwitch HWIC Switch Bedienungsanleitung

Cisco

Cisco VWIC-2MFT-T1 - Multiflex Trunk Voice/WAN Interface Card Expansion... Bedienungsanleitung

Cisco

Cisco Linksys WMA11B Bedienungsanleitung

Cisco

Cisco Aironet 340 Series Bedienungsanleitung

Cisco

Cisco HWIC-1FE - WAN Interface Card Expansion... Bedienungsanleitung

Beliebte Netzwerkkarte Handbücher anderer Marken

FirstComm

FirstComm OBiWiFi5G Bedienungsanleitung

Sun Microsystems

Sun Microsystems Interface Adapter Bedienungsanleitung

TRENDnet

TRENDnet TU2-ETG Bedienungsanleitung

YASKAWA

YASKAWA SI-EN3 Bedienungsanleitung

Paradyne

Paradyne BitStorm 2600 IP DSLAM Bedienungsanleitung

Belkin

Belkin F5D7050 Bedienungsanleitung

3Com

3Com EtherLink 3C509B Bedienungsanleitung

TRENDnet

TRENDnet TEG-PCITX Bedienungsanleitung

Delta Electronics

Delta Electronics Braking Modules VFDB Series Bedienungsanleitung

TwinMOS

TwinMOS Booming Bedienungsanleitung

Dialogic

Dialogic Media Board DM/V1200BTEPEQ Bedienungsanleitung

Buffalo

Buffalo AirStation WLI-PCM-L11GP Bedienungsanleitung

National Instruments

National Instruments NI 9234 Bedienungsanleitung

Hama

Hama 49276 Bedienungsanleitung

Linksys

Linksys WCF54G - Wireless-G Compact Flash Card Bedienungsanleitung

Compaq

Compaq Wireless LAN 100 Bedienungsanleitung

Bose

Bose PowerMatch Dante Bedienungsanleitung

TRENDnet

TRENDnet TEG-PCITXR Bedienungsanleitung