Cisco CTE 1400 Series Bedienungsanleitung

Quick Start Guide

Cisco CTE 1400 Series and Design Studio

1Introduction

2Install the Cisco CTE 1400 Series Hardware

3Upgrade the Cisco CTE 1400 Series Software

4Configure the CTE for the First Time

5Install Design Studio

6Start Design Studio

1Introduction

The Cisco Content Transformation Engine (CTE) 1400 Series handles requests for applications from

devices with microbrowser screens and uses transformation instructions to convert applications into

appropriate formats. Transformation instructions are created in the companion PC-based application,

Design Studio.

This document provides instructions for installing the CTE and performing the initial configuration

procedure.

2Install the Cisco CTE 1400 Series Hardware

This section describes how to install the CTE hardware in your network environment.

Requirements

To set up the CTE, you need the following hardware in addition to the items delivered with the CTE:

•Power cable

•Null-modem cable (9-pin female connector at both ends)

•A computer capable of hosting terminal console communication through a serial port

•One or two network cables to connect the CTE to a LAN

Procedure

The following steps summarize the hardware installation procedure described in the Cisco CTE 1400

Series Hardware Installation Guide:

Step 1 Install the CTE in a rack (if rack-mounted).

Step 2 Use network cables to connect the CTE NIC 1 (e0) port to your network (such as to a server

load balancer). For information on using the NIC 2 (e1) port, refer to the Cisco CTE

Configuration Note.

Step 3 Connect a null-modem cable to the 9-pin serial port on the CTE and connect the cable to a

computer that is capable of running terminal emulation software.

Step 4 On the computer, start a terminal emulation application. For example, start HyperTerminal.

Step 5 Set the serial connection to 9600 bits per second, 8 data bits, no parity, 1 stop bit; set the

Backspace key to issue a Delete character.

Hardware flow control is optional.

Step 6 Power up the CTE.

After about five minutes, the CTE serial console appears on the computer terminal.

You are now ready to configure the CTE with your network. If you are upgrading the CTE, go to

section 3. Otherwise, skip to section 4.

3Upgrade the Cisco CTE 1400 Series Software

If you are installing a new device, rather than an upgrade, skip this section.

Requirements

To upgrade to Release 2.7, you need the Release 2.7 Restore CD-ROM.

Note Be aware that an upgrade is a complete new installation, and it will overwrite any previous

CTE settings.

Upgrade Procedure

To upgrade your CTE, perform these steps:

Step 1 Make sure that a PC capable of hosting terminal emulation software is connected to the CTE;

power on both systems.

Step 2 Insert the CTE Release 2.7 Restore CD into the CD-ROM drive of the CTE.

Step 3 Power down the CTE.

Step 4 Wait 10 seconds.

Step 5 Power on the CTE.

Step 6 When the installation has completed, the serial console displays the message “Installation

successful.”

Step 7 When the upgrade is complete, eject the Restore CD and reboot the CTE.

Step 8 When the CTE restarts, the CTE serial console opens.

You are now ready to configure the CTE with your network.

4Configure the CTE for the First Time

This section describes the minimum configuration required to establish and test a connection between

your CTE and another device such as a server load balancer, switch, or web server.

Procedure

To configure the CTE, perform these general steps:

Step 1 In the CTE serial console, set the root password when prompted.

a. Enter a password of 8 or more characters.

b. Verify the password when prompted.

Step 2 Enter the IP address and netmask for Interface 0 when prompted:

IP address [x.x.x.x] (Enter 0 to clear):

ipAddress

Netmask [x.x.x.x] (Enter 0 to clear):

netmask

Step 3 Enter the IP address of the gateway device when prompted.

Gateway [x.x.x.x]:

gateway ipAddress

Step 4 The first DNS server is automatically set. If you want to change it, you can enter a different

IP address when prompted. Otherwise, press Enter to leave this setting unchanged.

DNS server[0] [x.x.x.x] (Enter 0 to clear):

Step 5 You can define two other DNS servers when prompted if you wish. To leave these values unset,

press Enter at each prompt.

Step 6 Enter the name, if any, that you want to use as your default domain name, such as

www.fox.com.

Domain Name [ ] (Enter 0 to clear):

Step 7 Type 1and then 6to ping the connected device.

If the ping command is successful, you have completed the initial configuration. If you are

unable to ping the connected device, refer to the Cisco CTE Configuration Note for

troubleshooting information.

For detailed information on other configuration settings, see the Cisco CTE Configuration Note.

Continue configuring the CTE from the Administration interface. Perform these steps:

Step 1 From a web browser, enter:

https://ipAddress:9001

Where:

– ipAddress is the IP address of your CTE

–9001 is the administration port

Step 2 Click the Network tab.

Step 3 Click Yes in the Security Alert dialog box.

Step 4 Log in as root, and enter the root password that you defined in the CTE serial console.

Step 5 On the Interfaces screen of the Network tab, define the Masquerade Host for Interface 0. The

masquerade host is an IP address that can be used for Network Address Translation (NAT).

Step 6 Click Submit to save your changes. Although a Restart Server button appears, you do not need

to restart the server yet.

Step 7 On the Ports screen of the Network tab, select from the Listen on Interface drop-down menu

the IP address that you have conﬁgured for Interface 0.

Step 8 Click Submit to save your changes and then click Restart Server.

Step 9 After the server restarts, click the Administration tab.

Step 10 Click Yes in the Security Information dialog box.

Step 11 On the Users screen of the Administration tab, specify a username and password for each

Design Studio user. Enter a username of at least 6 characters and a password of at least 8

characters. Click the Add User button.

From your web browser, check network connectivity by entering

http://ipAddress:httpPort.

For example, if the IP address of your CTE is 192.168.10.0 and its HTTP port is 80, enter

http://192.168.10.0:80.

If the ScreenTop Menu appears, the CTE is properly configured. If the ScreenTop Menu does

not appear, check the settings.

Continue to the next section to install Design Studio.

5Install Design Studio

Design Studio is the application that creates transformation rules. You also use Design Studio to

customize the default ScreenTop Menu that serves as a portal for devices connecting to the CTE.

Requirements

Design Studio requires the following:

•Windows 95, Windows 98/ME, Windows 2000, or Windows NT 4.0 with Service Pack 6.

•At least 25 MB of disk space.

•At least 128 MB of RAM; 256 MB is recommended.

•Internet Explorer version 5.0 or higher, or Netscape Navigator version 4.01 or higher.

•A VGA color monitor with a graphics card capable of showing 16-bit color or higher. A minimum

screen resolution of 640 x 480. Recommended resolution is 1280 x 1024.

•Network connection to the CTE.

The network connection can be through a proxy server, which you specify when you log in to

Design Studio.

Procedure

To install Design Studio, perform these steps:

Step 1 Insert the Design Studio CD-ROM into your CD-ROM drive.

If auto-start is enabled on your computer, the installer starts.

If auto-start is not enabled on your computer, double-click the drive icon for your CD-ROM,

and then double-click CiscoCTEDesignStudio.exe.

Step 2 Follow the instructions in the installer.

You may be asked to restart your PC during the installation. After you restart your PC, the

Design Studio installation wizard continues the installation.

By default, Design Studio is installed in C:\Program Files\Cisco\CTE\Design Studio.

Continue to the next section to start Design Studio.

6Start Design Studio

See the Design Studio Getting Started Guide for detailed information on installing and starting Design

Studio, as well as an overview of the product and a tutorial. For detailed information on using Design

Studio to create, preview, and publish transformation rules, see the Design Studio User Guide. That

information is also available from the Design Studio Help menu.

Requirements

To start Design Studio, you need the following login information from the administrator who sets up

the CTE:

•Your Design Studio username and password

•The IP address of the CTE

•The server upload port number

•HTTP and HTTPS proxy hosts and ports, if Design Studio and the CTE are connected through a

proxy server

Procedure

To start Design Studio, perform these steps:

Step 1 From the Windows Start menu, choose Program Files > Cisco > CTE > Design Studio.

The login dialog box appears.

Step 2 Enter your username and password.

Step 3 Enter the IP address of the CTE.

Step 4 If necessary, change the upload port number.

The default upload port number is 9001. You might need to change the port number if your

firewall redirects ports. Contact your CTE administrator if you do not know which port to

use.

Step 5 If the computer on which Design Studio is installed is connected to the CTE through a proxy

server, click Use Proxy and enter the host and port for HTTP and HTTPS connections.

Step 6 Click OK.

If you cannot connect to the CTE, verify that your computer has a network connection to a

running CTE. Contact your CTE administrator for help.

For More Information

All of the Design Studio and CTE documentation is available on the Design Studio CD-ROM. You can

also obtain the documentation from the Cisco home page (http://www.cisco.com) or order a printed

copy by calling Cisco corporate headquarters (California, USA) at 408 526-7208 or, elsewhere in

North America, by calling 800 553-NETS (6387).

Inhaltsverzeichnis

Andere Cisco Netzwerk-Hardware Handbücher

Cisco

Cisco LightStream 1010 Bedienungsanleitung

Cisco

Cisco NSS4100 - Gigabit Storage System Bedienungsanleitung

Cisco

Cisco ASR 5000 Bedienungsanleitung

Cisco

Cisco NCS 4206 Bedienungsanleitung

Cisco

Cisco CX-FEIP-1FX= Installation and con?guration Bedienungsanleitung

Cisco

Cisco AIR-BR1410A-A-K9 - Aironet 1410 Wireless... Bedienungsanleitung

Cisco

Cisco Aironet 340 Series Bedienungsanleitung

Cisco

Cisco ISA550 Bedienungsanleitung

Cisco

Cisco C7200-I - Input/Output Controller - Control... Bedienungsanleitung

Cisco

Cisco AIM-VPN - DES/3DES VPN Data Encryption AIM... Bedienungsanleitung

Cisco

Cisco Meraki Catalyst 9300/X/L-M Series Bedienungsanleitung

Cisco

Cisco NM-1FE-TX - Interface Module Ethernet Bedienungsanleitung

Cisco

Cisco CMX 3375 Bedienungsanleitung

Cisco

Cisco IAD2430 Series Handbuch

Cisco

Cisco ME 1200 Series Handbuch

Cisco

Cisco CWDM-OADM 1 Series Kurzanleitung

Cisco

Cisco ONS 15454 Handbuch

Cisco

Cisco NCS 4201 Handbuch

Cisco

Cisco SA-VAM - VPN Acceleration Module Bedienerhandbuch

Cisco

Cisco Firepower 1010 Bedienungsanleitung

Cisco

Cisco Firepower 2100 Series Bedienungsanleitung

Cisco

Cisco 1230AG - Aironet - Wireless Access Point Bedienungsanleitung

Cisco

Cisco ASR 901S Series Betriebsanleitung

Cisco

Cisco 7246 - uBR Router Bedienungsanleitung

Beliebte Netzwerk-Hardware Handbücher anderer Marken

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL Bedienungsanleitung

B&B Electronics

B&B Electronics ZXT9-IO-222R2 Bedienungsanleitung

Yudor

Yudor YDS-16 Bedienungsanleitung

D-Link

D-Link ShareCenter DNS-320L Bedienungsanleitung

Samsung

Samsung ES1642dc Gebrauchsanweisung

Honeywell Home

Honeywell Home LTEM-PV Montageanleitung

evertz

evertz 7700 Series Bedienungsanleitung

D-Link

D-Link ShareCenter DNS-343 Bedienungsanleitung

Asante

Asante AsanteBridge 1012 Bedienungsanleitung

FireBrick

FireBrick FB2700 Bedienungsanleitung

Audiovox Electronics

Audiovox Electronics ARWH2T Bedienungsanleitung

ADC

ADC DSX-1 Handbuch

NetComm

NetComm NF2 Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 5620 Bedienungsanleitung

Dell EMC

Dell EMC XC6420 Series Bedienungsanleitung

Lanner

Lanner NCA-1020A Bedienungsanleitung

Allied Telesis

Allied Telesis AT-TN121-A Bedienungsanleitung

Arista

Arista CCA-ETM-Q12 Bedienungsanleitung