Cisco MERAKI MX75 Bedienungsanleitung

MX75 Hardware Installation Guide

This guide provides instruction on how to install and configure your MX75 series device. This guide also provides mounting instructions and limited

troubleshooting procedures. For more MX device installation guides, refer to the MX installation guides section on our documentation website.

Product Overview

The Meraki MX75 is an enterprise security appliance designed for distributed deployments that require remote administration across medium branch

environments. It is ideal for network administrators who demand both ease of deployment and a state-of-the-art feature set. The Meraki Dashboard allows for

simple and easy deployment of the MX75 with minimal pre-configuration in almost any location.

Features

MX75 provides dedicated WAN uplinks, a single 1GbE SFP port, and 2 RJ45 1GbE ports. The LAN ports include 10 RJ45 1GbE ports. The MX75 is ready for

deployment in a variety of enterprise environments. MX75 appliance provides the following features:

• Managed via Cisco Meraki Dashboard

• Automatic Firmware upgrades

• WAN Link Balancing

• Automatic WAN Failover

• SD-WAN over Meraki AutoVPN

• L3/L7 Stateful Firewall

• Geo based firewall rules

• 1:1 and 1:Many NAT

• Configurable VLANs / DHCP support

• Static Routing

• Client VPN endpoint

• Meraki AutoVPN and L2TP/IPSec VPN endpoint

• Active Directory integration

• Content Filtering

• Malware Protection (AMP) w/ optional Threat Grid integration

• IDS/IPS protection

• Custom Traffic Shaping

• Historical Client Usage statistics

• Netflow support

• Syslog integration

• Remote Packet Capture tools

Context and Comparisons

MX68 MX75 MX85

# WAN Uplinks 2 3 4

Backup Cellular Uplink Built-in (Cellular Models Only), Via 3rd

Party USB Modem

Via 3rd Party USB Modem Via 3rd Party USB Modem

Stateful Firewall

Throughput 450 Mbps 1 Gbps 1 Gbps

Maximum site-to-site

VPN Throughput 200 Mbps 500 Mbps 500 Mbps

Advanced Security

Throughput 300 Mbps 800 Mbps 800 Mbps

PoE+ Capabilities Yes, 2x GbE RJ45 LAN Ports (802.3at) Yes, 2x RJ45 / 1 Gigabit Ethernet

port (LAN)

Yes, 1x RJ45 / 1 Gigabit Ethernet port

(WAN)

Recommended Use Case Small branch with up to 50 users Small branch office or retail

location with 200 users

Small to midsize branch office or retail

location with 250 users

Physical Specifications

MX68 MX75 MX85

# WAN Interfaces 234

Cellular WAN Interfaces Cellular Uplink via 3rd Party USB

Modem

Cellular Uplink via 3rd Party USB

Modem

Cellular Uplink via 3rd Party USB

Modem

LAN Interfaces - Dedicated 10x Dedicated GbE RJ45 10x Dedicated Gigabit Ethernet

RJ45 3x Dedicated GbE RJ45

LAN Interfaces - Convertible 2x Dedicated GbE RJ45 PoE+ 1x Convertible LAN/WAN GbE

RJ45

Mount Type Desktop / Wall Mount Desktop / Wall Mount Rack Mount

Dimensions

(h x d x w)

1.1 x 5.8 x 11.2 in /

27 x 148 x 284 mm

1.06" x 5.83" x 11.14"

27 x 148 x 283 mm

1.7” x 9.8“ x 19”

43.8 x 250 x 484.6mm

Weight 2.46 lb / 1.12 kg 1.87lb (0.85kg) 8.2lb (3.7kg)

Power Supply 100W DC (included) 100W DC (included) Internal 100-220V

50/60Hz AC

Power Load (idle/max) 11W / 79W 12W / 96W 12W / 55W

Operating Temperature 32°F - 104 °F

0°C - 40°C

32°F to 113°F

(0°C to 45°C)

32°F to 104°F

(0°C to 40°C)

Storage and Transportation

Temperature

-4°F - 158°F

-20°C - 70°C

-4°F - 158°F

-20°C - 70°C

-4°F - 158°F

-20°C - 70°C

Humidity 5% to 95% 5% to 95% 5% to 95%

Accessories

Accessory Description

MA-PWR-CORD-US 1x AC Power Cable, US plug

MA-PWR-CORD-EU 1x AC Power Cable, EU plug

MA-PWR-CORD-UK 1x AC Power Cable, UK plug

MA-PWR-CORD-AU 1x AC Power Cable, AU plug

Product View and Physical Features

Front Panels

MX75

Status Indicator

The MX75 series devices uses an LED to inform the user of the device's status. LED patterns and their meanings are described below.

LED Status Meaning

Solid orange Power is applied but the appliance is not connected to the Meraki

Dashboard

Rainbow Colors The appliance is attempting to connect to Meraki Dashboard

Flashing White Firmware upgrade in progress

Solid White Fully operational/connected, uplink actively using wired WAN

Solid Purple Fully operational/connected, uplink actively using integrated cellular failover

Back Panels

MX75

Note: Please refer to meraki.com for additional single-mode and multi-mode fiber transceiver modules

MX75 Back Panel Functions

Additional functions on the back panel are described below, from left to right.

USB port USB 3.0 for external 3G/4G wireless modems. Traffic status is indicated by

the USB LED.

WAN / Internet port This port provides connectivity to the WAN.

LAN ports

These 10 ports provide connectivity to computers, printers, access points, or

Ethernet switches.

A steady green LED indicates bidirectional connectivity, and flashing green

indicates traffic.

Power input Designed for use only with the unit’s power supply.

Reset button

Insert a paper clip if a reset is required.

Press for 1 second to delete a downloaded configuration and reboot.

Press and hold for more than 10 seconds to force a full factory reset.

Side Panels

MX75

MX75 Side Panel Functions

Additional functions on the side panel are described below, from left to right.

USB port USB 2.0 for 3G/4G wireless cards. Traffic status is indicated by the USB

LED.

Bottom Panel

Please note that the serial number is located on the product label at the bottom panel of MX75 devices

Package Contents

In addition to the MX device, the following are provided:

MX75

Power Adapter (No Power Cable)

2x CAT5 Ethernet Cables

Safety and Warnings

These operations are to be taken with respect to all local laws. Please take the following into consideration for safe operation:

• Power off the unit before you begin. Read the installation instructions before connecting the system to the power

source.

• Before you work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar with

standard practices for preventing accidents.

• Read the mounting instructions carefully before beginning installation. Failure to use the correct hardware or to

follow the correct procedures could result in a hazardous situation to people and damage to the system.

• This product relies on the building’s installation for short-circuit (overcurrent) protection. Ensure that the protective

device is rated not greater than: 15 A, 125 Vac, or 10A, 240 Vac.

• Please only power the device with the provided power cables to ensure regulatory compliance.

Pre-install Preparation

You should complete the following steps before going on-site to perform an installation.

Configure your Dashboard Network

The following is a brief overview only of the steps required to add an MX to your network. For detailed instructions about creating, configuring and managing

Meraki networks, refer to the online documentation (documentation.meraki.com).

1. Login to http://dashboard.meraki.com. If this is your ﬁrst time, create a new account.

2. Find the network to which you plan to add your MX or create a new network.

3. Add your MX to your network. You will need your Meraki order number (found on your invoice) or the serial

number of each MX, which looks like Qxxx-xxxx-xxxx, and is found on the bottom of the unit. You will also need

your Enterprise license key, which you should have received via email.

4. Go to the map / ﬂoor plan view and place each MX on the map by clicking and dragging it to the location where

you plan to mount it.

Check and Set Firmware

To ensure your MX performs optimally immediately following installation, it is recommended that you facilitate a ﬁrmware upgrade prior to mounting your MX.

1. Attach your MX to power and a wired Internet connection.

2. The MX will turn on and the power LED will glow solid orange.

3. If the unit requires an upgrade, the power LED will begin blinking white until the upgrade is complete, at which

point the LED will turn solid white. You should allow at least a few minutes for the ﬁrmware upgrade to complete,

depending on the speed of your internet connection.

Check and Configure Upstream Firewall Settings

If an upstream ﬁrewall is already in place, it must allow outgoing connections on particular ports to particular IP addresses. The most current list of outbound

ports and IP addresses for your particular organization can be found on the firewall configuration page in your dashboard.

Installation Instructions

Mounting Recommendations

You can mount the appliance on a drywall surface, either vertically or horizontally. The distance between the holes you drill should be 5-1/8 inches (13 cm). The

fan grills for the MX75 are located at the bottom of the chassis.

Note: Please make sure there are no blockages or obstructions within one inch of the top of the chassis or within 0.5 inches of the sides so that

nothing interferes with cooling.

Connecting to WAN

All Meraki MX devices must have an IP address. This section describes how to configure your local area network before you deploy it. A local management web

service, running on the appliance, is accessed through a browser running on a client PC. This web service is used for configuring and monitoring basic ISP/WAN

connectivity.

Setting up a Static IP Address

Do the following to configure basic connectivity and other networking parameters:

1. Using a client machine such as a laptop, connect to one of the LAN ports of the MX.

2. Using a browser on the client machine, access the appliance's built-in web service by browsing to

http://setup.meraki.com. (You do not have to be connected to the Internet to reach this address)

3. Click Uplink configuration under the Local status tab. The default credentials use the device serial number as

the username, with a blank password field.

4. Choose Static for the IP Assignment option.

5. Enter the IP address, subnet mask, default gateway IP and DNS server information.

Setting up a DHCP IP Address

By default all MX devices are configured to DHCP from upstream WAN / ISP servers. Simply plug the MX's WAN / Internet port to your upstream circuit and wait

a few minutes for the unit to negotiate a DHCP address.

Additional Settings

Setting VLANs

If your WAN uplink is on a trunk port, choose VLAN tagging > Use VLAN tagging and enter the appropriate value for VLAN ID for your network.

Setting up a Secondary WAN Interface on the MX75

MX75 comes with three dedicated Internet ports, which are both configured under Security & SD-WAN > Monitor > Appliance Status in the Uplink tab.

Setting PPPoE

PPPoE authentication may be required if you are connecting MX device to a DSL circuit. You need to know your authentication option and credentials (supplied

by your ISP) in order to complete these steps.

To ensure that the client PC is redirected to the local web service in the following step, you must disable all other network services (ex: wi-fi) on your

client machine.

When the WAN connection is fully enabled, Internet LED 1 will turn green.

Please note that all these settings below are accessible only via the local management console.

• Choose Connection Type > PPPoE.

• Select your Authentication option.

• If you select Use authentication, enter appropriate values for Username and Password.

Web Proxy Settings

These settings take effect if the MX device has to fall back to using HTTP to contact the Cloud Controller. By default, web proxy is disabled. To enable web

proxy, do the following:

• Choose Web proxy > Yes.

• Enter values as appropriate for Hostname or IP and Port.

• If you require authentication, choose Authentication > Use authentication, and enter appropriate values for

Username and Password.

Configuring Physical Link Settings

To configure physical link settings on the Ethernet ports, click Local status > Ethernet configuration. You can enable half duplex, full duplex, and

autonegotiation, as well as set 10/100/1000-Mbps data rates.

Basic Troubleshooting

The following steps can be used for troubleshooting basic connectivity issues with your MX.

• Reset the MX

• Factory reset the MX by holding the factory reset button for 10-15 seconds

• Try switching cables, or testing your cable on another device

Reference https://documentation.meraki.com/MX for additional information and troubleshooting tips.

If you are still experiencing hardware issues, please contact Cisco Meraki support by logging in to dashboard and using the Help option near the top of the page,

then opening and email case or calling using the contact information on that page.

Warranty

MX Warranty coverage periods are as follows:

MX (e.g. MX75) Lifetime Full lifetime hardware warranty with next-day advanced replacement included.

MX Accessories 1 Year The following are considered accessories:

SFP Modules, all mounting kits and stands, interface modules, additional power cords

Note: The above table is a general guideline for warranty terms and is not final. Warranty terms are subject to printed warranty information on the relevant online

Meraki data sheets.

To apply all configuration settings to the appliance, be sure to click Save Settings at the bottom of the page.

If your Cisco Meraki device fails and the problem cannot be resolved by troubleshooting, contact support to address the issue. Once support determines that the

device is in a failed state, they can process an RMA and send out a replacement device free of charge. In most circumstances, the RMA will include a pre-paid

shipping label so the faulty equipment can be returned.

Additional warranty information can be found on: https://meraki.cisco.com/support#process:warranty

Support and Additional Information

If issues are encountered with device installation or additional help is required, contact Meraki Support by logging in to dashboard.meraki.com and opening a

case by visiting the Get Help section.

• The equipment is intended for industrial or other commercial activities.

• The equipment is used in areas without exposure to harmful and dangerous production factors, unless otherwise

specified in the operational documentation and/or on the equipment labeling.

• The equipment is not for domestic use. The equipment is intended for operation without the constant presence of

maintenance personnel.

• The equipment is subject to installation and maintenance by specialists with the appropriate qualifications, sufficient

specialized knowledge, and skills.

• Rules and conditions for the sale of equipment are determined by the terms of contracts concluded by Cisco or

authorized Cisco partners with equipment buyers.

• Disposal of a technical device at the end of its service life should be carried out in accordance with the requirements

of all state regulations and laws.

• Do not throw in the device with household waste. The technical equipment is subject to storage and disposal in

accordance with the organization's disposal procedure.

• The equipment should be stored in its original packaging in a room protected from atmospheric precipitation. The

permissible temperature and humidity ranges during storage are specified in the Operation (Installation) Manual.

• Transportation of equipment should be carried out in the original packaging in covered vehicles by any means of

transport. The temperature and humidity during transportation must comply with the permissible established ranges

of temperature and humidity during storage (in the off state) specified in the Operation Manual (Installation)

For additional information on Meraki hardware and for other installation guides, please refer to documentation.meraki.com.

In order to initiate a hardware replacement for non-functioning hardware that is under warranty, you must have access to the original packaging the

hardware was shipped in. The original hardware packaging includes device serial number and order information, and may be required for return

shipping.

Meraki MX75 devices have been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC rules. A digital

device that is marketed for use in a residential environment notwithstanding use in commercial, business and industrial environments.

Inhaltsverzeichnis

Andere Cisco Netzwerk-Hardware Handbücher

Cisco

Cisco ISA550 Bedienungsanleitung

Cisco

Cisco Nexus 93600CD-GX Handbuch

Cisco

Cisco ONS 15454 SDH E1-75 Bedienungsanleitung

Cisco

Cisco VIC-2FXS - 3600 Voice Interface Card-Fxs... Bedienungsanleitung

Cisco

Cisco NCS 2002 Bedienungsanleitung

Cisco

Cisco 5500 Series Bedienungsanleitung

Cisco

Cisco AIR-BR1410A-A-K9 - Aironet 1410 Wireless... Kurzanleitung

Cisco

Cisco EXPLORER 3100 Bedienungsanleitung

Cisco

Cisco MA-UMNT-MR-A3 Bedienungsanleitung

Cisco

Cisco VSVM Bedienungsanleitung

Cisco

Cisco NM-1FE-TX - Interface Module Ethernet Bedienungsanleitung

Cisco

Cisco LightStream 1010 Bedienungsanleitung

Cisco

Cisco 1230AG - Aironet - Wireless Access Point Bedienungsanleitung

Cisco

Cisco Rack-Mount and Cable Mgmt. 7505/7010 Bedienungsanleitung

Cisco

Cisco NCS 1001 Handbuch

Cisco

Cisco NCS 1002 Bedienungsanleitung

Cisco

Cisco AIM-VPN - DES/3DES VPN Data Encryption AIM... Bedienungsanleitung

Cisco

Cisco Firepower 2100 Series Bedienungsanleitung

Cisco

Cisco UCS 6248 UP Bedienungsanleitung

Cisco

Cisco NM-1A-T3 - 1port Ds3 Atm Network Module Bedienungsanleitung

Cisco

Cisco IP/VC 3500 Originalbetriebsanleitung

Cisco

Cisco ONS 15454 SDH Handbuch

Cisco

Cisco VIP-4R/4T Bedienungs- und Wartungsanleitung

Cisco

Cisco UCS X10c Montage- und Wartungsanleitung

Beliebte Netzwerk-Hardware Handbücher anderer Marken

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL Bedienungsanleitung

B&B Electronics

B&B Electronics ZXT9-IO-222R2 Bedienungsanleitung

Yudor

Yudor YDS-16 Bedienungsanleitung

D-Link

D-Link ShareCenter DNS-320L Bedienungsanleitung

Samsung

Samsung ES1642dc Gebrauchsanweisung

Honeywell Home

Honeywell Home LTEM-PV Montageanleitung

evertz

evertz 7700 Series Bedienungsanleitung

D-Link

D-Link ShareCenter DNS-343 Bedienungsanleitung

Asante

Asante AsanteBridge 1012 Bedienungsanleitung

FireBrick

FireBrick FB2700 Bedienungsanleitung

Audiovox Electronics

Audiovox Electronics ARWH2T Bedienungsanleitung

ADC

ADC DSX-1 Handbuch

NetComm

NetComm NF2 Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 5620 Bedienungsanleitung

Dell EMC

Dell EMC XC6420 Series Bedienungsanleitung

Lanner

Lanner NCA-1020A Bedienungsanleitung

Allied Telesis

Allied Telesis AT-TN121-A Bedienungsanleitung

Arista

Arista CCA-ETM-Q12 Bedienungsanleitung