Cisco UCS C Series Bedienungsanleitung

Installing the Server

•Preparing for Installation, on page 1

•Installing the Server in a Rack, on page 4

•Initial Server Setup, on page 10

•NIC Mode and NIC Redundancy Settings, on page 15

•Accessing the System BIOS, on page 16

•Updating the BIOS and Cisco IMC Firmware, on page 17

Preparing for Installation

Installation Warnings and Guidelines

Before you install, operate, or service a server, review the Regulatory Compliance and Safety Information

for Cisco UCS C-Series Servers for important safety information.

Note

IMPORTANT SAFETY INSTRUCTIONS

This warning symbol means danger. You are in a situation that could cause bodily injury. Before you

work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar with

standard practices for preventing accidents. Use the statement number provided at the end of each

warning to locate its translation in the translated safety warnings that accompanied this device.

Statement 1071

Warning

To prevent the system from overheating, do not operate it in an area that exceeds the maximum

recommended ambient temperature of: 35° C (95° F).

Statement 1047

Warning

Installing the Server

Theplug-socketcombinationmustbeaccessibleatalltimes,becauseitserves as the main disconnecting

device.

Statement 1019

Warning

This product relies on the building’s installation for short-circuit (overcurrent) protection. Ensure that

the protective device is rated not greater than: 250 V, 15 A.

Statement 1005

Warning

Installation of the equipment must comply with local and national electrical codes.

Statement 1074

Warning

This unit is intended for installation in restricted access areas. A restricted access area can be accessed

only through the use of a special tool, lock, and key, or other means of security.

Statement 1017

Warning

This equipment must be grounded. Never defeat the ground conductor or operate the equipment in the

absence of a suitably installed ground conductor. Contact the appropriate electrical inspection authority

or an electrician if you are uncertain that suitable grounding is available.

Statement 1024

Warning

For Nordic countries (Norway, Finland, Sweden and Denmark) this system must be installed in a

Restricted Access Location, where the voltage of the main ground connection of all equipment is the

same (equipotential earth) and the system is connected to a grounded electrical outlet.

Statement 328

Warning

High leakage current –earth connection essential before connection to system power supply.

Statement 342

Warning

Installing the Server

Installation Warnings and Guidelines

This equipment must be externally grounded using a customer-supplied ground wire before power is

applied. Contact the appropriate electrical inspection authority or an electrician if you are uncertain

that suitable grounding is available.

Statement 366

Warning

To ensure proper airflow it is necessary to rack the servers using rail kits. Physically placing the units on top

of one another or “stacking” without the use of the rail kits blocks the air vents on top of the servers, which

could result in overheating, higher fan speeds, and higher power consumption. We recommend that you mount

your servers on rail kits when you are installing them into the rack because these rails provide the minimal

spacing required between the servers. No additional spacing between the servers is required when you mount

the units using rail kits.

Caution

Avoid uninterruptible power supply (UPS) types that use ferroresonant technology. These UPS types can

become unstable with systems such as the Cisco UCS, which can have substantial current draw fluctuations

from fluctuating data traffic patterns.

Caution

When you are installing a server, use the following guidelines:

• Plan your site configuration and prepare the site before installing the server. See the Cisco UCS Site

Preparation Guide for the recommended site planning tasks.

• Ensure that there is adequate space around the server to allow for accessing the server and for adequate

airflow. The airflow in this server is from front to back.

•Ensure that the air-conditioning meets the thermal requirements listed in the Environmental Specifications.

• Ensure that the cabinet or rack meets the requirements listed in the Rack Requirements, on page 3.

• Ensure that the site power meets the power requirements listed in the Power Specifications. If available,

you can use an uninterruptible power supply (UPS) to protect against power failures.

Rack Requirements

The rack must be of the following type:

• A standard 19-in. (48.3-cm) wide, four-post EIA rack, with mounting posts that conform to English

universal hole spacing, per section 1 of ANSI/EIA-310-D-1992.

•The rack-post holes can be square 0.38-inch (9.6 mm), round 0.28-inch (7.1 mm), #12-24 UNC, or #10-32

UNC when you use the Cisco-supplied slide rails.

• The minimum vertical rack space per server must be four rack units (RUs), equal to 7.0 in. (177.8 mm).

Supported Cisco Slide Rail Kits

The server supports the following rail kit options:

Installing the Server

Rack Requirements

• Cisco part UCSC-RAIL-4U-M5= (ball-bearing slide rail kit)

• Cisco part UCSC-CMA-4U-M5= (cable management arm)

Rack Installation Tools Required

The slide rails sold by Cisco Systems for this server do not require tools for installation.

Slide Rail and Cable Management Arm Dimensions

The slide rails for this server have an adjustment range of 24 to 36 inches (610 to 914 mm).

The optional cable management arm (CMA) adds additional length requirements:

• The additional distance from the rear of the server to the rear of the CMA is 5.4 inches (137.4 mm).

• The total length of the server including the CMA is 35.2 inches (894 mm).

Installing the Server in a Rack

To prevent bodily injury when mounting or servicing this unit in a rack, you must take special

precautions to ensure that the system remains stable. The following guidelines are provided to ensure

your safety:

This unit should be mounted at the bottom of the rack if it is the only unit in the rack.

When mounting this unit in a partially filled rack, load the rack from the bottom to the top with the

heaviest component at the bottom of the rack.

If the rack is provided with stabilizing devices, install the stabilizers before mounting or servicing the

unit in the rack.

Statement 1006

Warning

Step 1 Remove the inner rail from the slide rail assembly:

a) Slide out the intermediate and inner slide rails until they click and lock in the fully open position.

b) Hold down the inner rail release clip and at the same time, pull the inner rail free from the assembly.

c) Push down the rail release latch while you collapse the intermediate rail back into the rail assembly.

Installing the Server

Installing the Server in a Rack

Figure 1: Removing the Inner Rail From the Assembly

Inner rail release clip2Rail release latch1

Step 2 Attach the inner rails to the sides of the server:

The inner rails are not identical: there is a left rail and a right rail (as viewed from the chassis front). The inner

rails are marked with “L” for left or “R” for right.

Note

a) Align the left inner rail marked “L” with the left side of the chassis (as viewed from the front). Align the 10 keyed

slots in the rail with the 10 pegs on the side of the chassis.

b) Set the keyed slots over the pegs, and then slide the rail toward the front to lock it in place on the pegs.

c) Install the right inner rail marked “R” to the right side of the chassis (as viewed from the front).

Installing the Server

Installing the Server in a Rack

Figure 2: Attaching the Inner Rail to the Side of the Server

Right-side inner rail marked "R"3Left side of chassis1

-Right side of chassis2

Step 3 Install the slide rail assemblies into the rack:

The slide rail assemblies are not identical; there is a left rail and a right rail (as viewed from the rack front).

The assemblies are marked with “L” for left or “R” for right.

Note

a) Align the front end of the left-side slide-rail assembly (marked “L”) with the left-front rack-post (as you face the

front of the rack).

The slide rail front-end wraps around the outside of the rack post and the mounting pegs enter the rack-post holes

from the outside-front.

The bottom of the slide rail assembly lines up with the intended bottom of the rack unit.

b) Push the front mounting pegs into the rack-post holes until you hear them click and lock.

c) Adjust the slide-rail length until it reaches the rear rack post perfectly level.

Ensure that the rail is perfectly level and that the same height rack-post holes are used in the front and rear

posts.

Note

d) Hold open the rear-peg spring latch, then push the rear mounting pegs into the rear rack-post-holes

The rear mounting pegs enter the rear rack-post holes from the inside of the rack post.

e) Release the rear-peg spring latch to lock the rear pegs in place.

f) Attach the second slide-rail assembly to the opposite side of the rack. Ensure that the two slide-rail assemblies are at

the same height and are level front-to-back.

Ensure that all pegs are fully inserted into the rack post holes before installing the server to the rack.

Caution

Installing the Server

Installing the Server in a Rack

Figure 3: Attaching the Rail Assembly to the Rack Post

Rear peg spring-latch3Front mounting pegs, entering rack-post holes

from the outside front

-Rear mounting pegs, entering rack-post holes

from inside rear

Step 4 Pull the inner slide rails on each assembly out toward the rack front until they hit the internal stops and lock in place.

Step 5 Insert the server into the slide rails:

This server can weigh up to 146 pounds (66.2 kilograms) when fully loaded with components. We recommend

that you use a minimum of two people or a mechanical lift when lifting the server. Attempting this procedure

alone could result in personal injury or equipment damage.

Caution

The rack rail channels are fragile to side loads. Install the chassis gently to avoid damaging the rails.

Note

a) Align the rear ends of the inner rails that are attached to the server sides with the front ends of the empty intermediate

rails on the rack.

Ensure that the inner rails on the chassis are parallel with the intermediate rails on the rack. This could

require adjusting the mechanical lift position up-down and left-to-right. Consider using shims if your lift

does not support these motions. The ends of the inner rail must align up-down and side-to-side with the

ends of the intermediate rails.

Caution

b) Very slowly push the chassis toward the rack. Ensure that the rail ends mesh to each other and are fully engaged at

the top and bottom of the rail channels.

Installing the Server

Installing the Server in a Rack

c) Slowly push the inner rails into the slide rails on the rack until they stop at the internal stops.

d) Press the release clip on each inner rail inward, and then continue pushing the server into the rack until its front

slam-latches engage with the rack posts.

Ensure that both inner rail release clips are pushed in before pushing the server into the rack. Push the

server into the rails slowly to avoid damaging the rails. Let go of the release clip buttons as the server begins

to push in.

Caution

Figure 4: Inner-Rail Release Clip

Inner rail release clip3Intermediate rail extended from outer rail1

-Inner rail attached to server2

Step 6 (Optional) Secure the server in the rack more permanently by using the two screws that are provided with the slide rails.

Always perform this step if you plan to move the rack with servers installed.

With the server fully pushed into the slide rails, open a hinged slam latch lever on the front of the server and insert a

screw through the hole that is under the lever. The screw threads into the static part of the rail on the rack post and prevents

the server from being pulled out. Repeat for the opposite slam latch.

Depressing the release clips on the inner rails allows the chassis to slide all the way out of the intermediate rails

and could result in injury or equipment damage. When you pull the chassis outward from the rack, it stops at

internal locking stops. Do not depress the inner-rail release clips unless you intend to slide the chassis back

into the rack or to fully remove the chassis from the rack. It is recommended that when you test pulling the

chassis out from the rack for the first time that you place the mechanical lift under the chassis to avoid an

accidental drop.

Caution

Installing the Server

Installing the Server in a Rack

Installing the Cable Management Arm (Optional)

The cable management arm (CMA) is reversible left-to-right. To reverse the CMA, see Reversing the Cable

Management Arm (Optional), on page 10 before installation.

Note

Step 1 With the server pushed fully into the rack, slide the CMA tab of the CMA arm that is farthest from the server onto the

end of the stationary slide rail that is attached to the rack post. Slide the tab over the end of the rail until it clicks and

locks.

Figure 5: Attaching the CMA to the Rear Ends of the Slide Rails

CMA tab on width-adjustment slider attaches

to end of stationary outer slide rail.

3CMA tab on arm farthest from server attaches

to end of stationary outer slide rail.

Rear of server4CMA tab on arm closest to the server attaches

to end of inner slide rail attached to server.

Step 2 Slide the CMA tab that is closest to the server over the end of the inner rail that is attached to the server. Slide the tab

over the end of the rail until it clicks and locks

Step 3 Pull out the width-adjustment slider that is at the opposite end of the CMA assembly until it matches the width of your

rack.

Step 4 Slide the CMA tab that is at the end of the width-adjustment slider onto the end of the stationary slide rail that is attached

to the rack post. Slide the tab over the end of the rail until it clicks and locks.

Installing the Server

Installing the Cable Management Arm (Optional)

Step 5 Open the hinged flap at the top of each plastic cable guide and route your cables through the cable guides as desired.

Reversing the Cable Management Arm (Optional)

Step 1 Rotate the entire CMA assembly 180 degrees, left-to-right. The plastic cable guides must remain pointing upward.

Step 2 Flip the tabs at the ends of the CMA arms so that they point toward the rear of the server.

Step 3 Pivot the tab that is at the end of the width-adjustment slider. Depress and hold the metal button on the outside of the tab

and pivot the tab 180 degrees so that it points toward the rear of the server.

Figure 6: Reversing the CMA

Metal button on outside of tab2CMA tab on end of width-adjustment slider1

Initial Server Setup

This section describes how to power on the server, assign an IP address, and connect to server management

when using the server in standalone mode. To use the server in Cisco UCS Manager integration, specific

cabling and settings are required. See Installation For Cisco UCS Manager Integration.

Note

Installing the Server

Reversing the Cable Management Arm (Optional)

Andere Handbücher für UCS C Series

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Cisco Server Handbücher

Cisco

Cisco UCS E Series Handbuch

Cisco

Cisco UCS C240 M3 Kurzanleitung

Cisco

Cisco UCS C220 M5SX Bedienungsanleitung

Cisco

Cisco MCS-7825-H1-IPC1 Bedienungsanleitung

Cisco

Cisco UCS B200 Handbuch

Cisco

Cisco 7835-H2 - Media Convergence Server Bedienungsanleitung

Cisco

Cisco UCS C460 M2 Bedienungsanleitung

Cisco

Cisco Profile Series Bedienungsanleitung

Cisco

Cisco NAC-3300 Series Bedienungsanleitung

Cisco

Cisco UCS 82598KR Bedienungsanleitung

Cisco

Cisco UCS B250 M1 Handbuch

Cisco

Cisco UCS C200 M2 Systemhandbuch

Cisco

Cisco CRS-16 DC Bedienungsanleitung

Cisco

Cisco UCS B200 M4 Bedienungsanleitung

Cisco

Cisco UCS B460 M4 Handbuch

Cisco

Cisco UCS C240 M3 Bedienungsanleitung

Cisco

Cisco AS5300 - Universal Access Server Technisches Dokument

Cisco

Cisco CiscoWorks WLSE 1130-19 Bedienerhandbuch

Cisco

Cisco UCS B440 M2 Bedienungsanleitung

Cisco

Cisco UCS C240 Montage- und Wartungsanleitung

Cisco

Cisco UCS C460 Montage- und Wartungsanleitung

Cisco

Cisco UCS B200 M4 Handbuch

Cisco

Cisco C880 M4 Bedienungsanleitung

Cisco

Cisco L2TP Bedienungsanleitung

Beliebte Server Handbücher anderer Marken

HP AlphaServer ES47 Bedienungsanleitung

Dell

Dell PowerEdge R410 Bedienungsanleitung

PowerNAS

PowerNAS CMA Bedienungsanleitung

Supero

Supero FatTwin F617R3-FT Bedienungsanleitung

MSI

MSI P1-109N-L70 Bedienungsanleitung

Dell

Dell PowerEdge XE9640 Handbuch

Dell

Dell PS4100 Montageanleitung

EtroVISION

EtroVISION EV3151 Bedienungsanleitung

NEC

NEC Express5800/T110j Bedienungsanleitung

HP ProLiant Gen9 Bedienungsanleitung

Compaq

Compaq ProLiant 3000 Handbuch

Dell

Dell PowerEdge 3YPMN Bedienungsanleitung

iRobo

iRobo IPC2U Bedienungsanleitung

Nortel

Nortel 1000 Con?guration guide Bedienungsanleitung

Asus

Asus AP7500 Bedienungs- und Wartungshandbuch

Avid Technology

Avid Technology AirSpeed 5000 Bedienungsanleitung

HP Integrity rx2600 Installationsanleitung

Milestone

Milestone Husky IVO 350T Bedienungsanleitung