Cisco UCS B250 M1 Handbuch

Send document comments to ucs-docfeedbac[email protected]

Americas Headquarters:

Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA 95134-1706 USA

Cisco UCS B250 Extended Memory Blade Server

Installation and Service Note

Last Revised: August 22, 2011

The UCS B250 blade server (shown in Figure 1) is available in both M1 and M2 versions. This document

applies equally to both versions. The Cisco UCS B250 is a full-width blade with 48 DIMM slots for up

to 384 GB of memory; it supports two adapters. You may install up to four UCS B250 Blade Servers to

a UCS chassis.

Figure 1 UCS B250 Extended Memory Blade Server

1Hard drive bay 1 8Power button and LED

2Hard drive bay 2 9Network link status LED

3Left ejector captive screw 10 Blade health LED

4Left blade ejector handle 11 Console connector

5Asset tab 1

1. Each server has a blank plastic tag that pulls out of the front panel, provided so you can add your

own asset tracking label without interfering with the intended air flow.

12 Reset button access

6Right blade ejector handle 13 Beaconing LED and button

7Right ejector captive screw

Send document comments to ucs-docfeedbac[email protected]

Cisco UCS B250 Extended Memory Blade Server Installation and Service Note

OL-22474-03

LEDs

The LED indicators (see Table 1) indicate whether the blade server is in active or standby mode, the

status of the network link, the overall health of the blade server, and whether the server is set to give a

flashing blue beaconing indication.

The removable hard disks also have LEDs indicating hard disk access activity and hard disk health.

Buttons

The Reset button is just inside the chassis and must be pressed using the tip of a paper clip or a similar

item. Hold the button down for five seconds and then release it to restart the server if other methods of

restarting are not working.

The beaconing function for an individual server may be turned on or off by pressing the combination

button and LED. See Table 1 for details. Beaconing will be reflected in the UCS Manager interface and

can also be turned off and on from there.

The power button and LED allows you to manually take a server temporarily out of service but leave it

in a state where it can be restarted quickly, or to bring it back into service. If the desired power state for

a service profile associated with a blade server or an integrated rack-mount server is set to "off", using

the power button or Cisco UCS Manager to reset the server will cause the desired power state of the

server to become out of sync with the actual power state and the server may unexpected shutdown at a

later time. To safely reboot a server from a power-down state, use the Boot Server action in Cisco UCS

Manager.

Table 1 Blade Server LEDs

LED Color Description

Power Off Power off

Green Normal operation

Amber Standby

Link Off None of the network links are up

Green At least one network link is up

Health Off Power off

Green Normal operation

Amber Minor error

Blinking

Amber

Critical error

Beaconing Off Beaconing not enabled.

Blinking

blue 1 Hz

Beaconing to locate a selected blade—If the LED is not

blinking, the blade is not selected. You can initiate

beaconing in UCS Manager or with the button.

Activity

(Disk Drive)

Off Inactive.

Green Outstanding I/O to disk drive

Health

(Disk Drive)

Off No fault

Amber Some fault

Send document comments to ucs-docfeedbac[email protected]

Cisco UCS B250 Extended Memory Blade Server Installation and Service Note

OL-22474-03

Connectors

A console port is provided to give a direct connection to a blade server to allow operating system

installation and other management tasks to be done directly rather than remotely. The port uses the KVM

dongle device included in the chassis accessory kit.

The KVM cable (N20-BKVM, shown in Figure 2) provides a connection into a Cisco UCS blade server;

it has a a DB9 serial connector, a VGA connector for a monitor, and dual USB ports for a keyboard and

mouse. With this cable you can create a direct connection to the operating system and the BIOS running

on a blade server.

Figure 2 KVM Cable for Blade Servers

Conventions

This document uses the following conventions for notes, cautions, and safety warnings.

Notes and Cautions contain important information that you should know.

Note Means reader take note. Notes contain helpful suggestions or references to material that are not covered

in the publication.

Caution Means reader be careful. You are capable of doing something that might result in equipment damage or

loss of data.

Safety warnings appear throughout this publication in procedures that, if performed incorrectly, can

cause physical injuries. A warning symbol precedes each warning statement.

1Connector to blade server slot 3VGA connection for a monitor

2DB9 serial connector 42-port USB connector for a mouse and keyboard

Send document comments to ucs-docfeedbac[email protected]

Cisco UCS B250 Extended Memory Blade Server Installation and Service Note

OL-22474-03

Warning

IMPORTANT SAFETY INSTRUCTIONS

This warning symbol means danger. You are in a situation that could cause bodily injury. Before you

work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar

with standard practices for preventing accidents. Use the statement number provided at the end of

each warning to locate its translation in the translated safety warnings that accompanied this

device.

Statement 1071

SAVE THESE INSTRUCTIONS

Waarschuwing

BELANGRIJKE VEILIGHEIDSINSTRUCTIES

Dit waarschuwingssymbool betekent gevaar. U verkeert in een situatie die lichamelijk letsel kan

veroorzaken. Voordat u aan enige apparatuur gaat werken, dient u zich bewust te zijn van de bij

elektrische schakelingen betrokken risico's en dient u op de hoogte te zijn van de standaard

praktijken om ongelukken te voorkomen. Gebruik het nummer van de verklaring onderaan de

waarschuwing als u een vertaling van de waarschuwing die bij het apparaat wordt geleverd, wilt

raadplegen.

BEWAAR DEZE INSTRUCTIES

Varoitus

TÄRKEITÄ TURVALLISUUSOHJEITA

Tämä varoitusmerkki merkitsee vaaraa. Tilanne voi aiheuttaa ruumiillisia vammoja. Ennen kuin

käsittelet laitteistoa, huomioi sähköpiirien käsittelemiseen liittyvät riskit ja tutustu

onnettomuuksien yleisiin ehkäisytapoihin. Turvallisuusvaroitusten käännökset löytyvät laitteen

mukana toimitettujen käännettyjen turvallisuusvaroitusten joukosta varoitusten lopussa näkyvien

lausuntonumeroiden avulla.

SÄILYTÄ NÄMÄ OHJEET

Attention

IMPORTANTES INFORMATIONS DE SÉCURITÉ

Ce symbole d'avertissement indique un danger. Vous vous trouvez dans une situation pouvant

entraîner des blessures ou des dommages corporels. Avant de travailler sur un équipement, soyez

conscient des dangers liés aux circuits électriques et familiarisez-vous avec les procédures

couramment utilisées pour éviter les accidents. Pour prendre connaissance des traductions des

avertissements figurant dans les consignes de sécurité traduites qui accompagnent cet appareil,

référez-vous au numéro de l'instruction situé à la fin de chaque avertissement.

CONSERVEZ CES INFORMATIONS

Warnung

WICHTIGE SICHERHEITSHINWEISE

Dieses Warnsymbol bedeutet Gefahr. Sie befinden sich in einer Situation, die zu Verletzungen führen

kann. Machen Sie sich vor der Arbeit mit Geräten mit den Gefahren elektrischer Schaltungen und

den üblichen Verfahren zur Vorbeugung vor Unfällen vertraut. Suchen Sie mit der am Ende jeder

Warnung angegebenen Anweisungsnummer nach der jeweiligen Übersetzung in den übersetzten

Sicherheitshinweisen, die zusammen mit diesem Gerät ausgeliefert wurden.

BEWAHREN SIE DIESE HINWEISE GUT AUF.

Send document comments to ucs-docfeedbac[email protected]

Cisco UCS B250 Extended Memory Blade Server Installation and Service Note

OL-22474-03

Avvertenza

IMPORTANTI ISTRUZIONI SULLA SICUREZZA

Questo simbolo di avvertenza indica un pericolo. La situazione potrebbe causare infortuni alle

persone. Prima di intervenire su qualsiasi apparecchiatura, occorre essere al corrente dei pericoli

relativi ai circuiti elettrici e conoscere le procedure standard per la prevenzione di incidenti.

Utilizzare il numero di istruzione presente alla fine di ciascuna avvertenza per individuare le

traduzioni delle avvertenze riportate in questo documento.

CONSERVARE QUESTE ISTRUZIONI

Advarsel

VIKTIGE SIKKERHETSINSTRUKSJONER

Dette advarselssymbolet betyr fare. Du er i en situasjon som kan føre til skade på person. Før du

begynner å arbeide med noe av utstyret, må du være oppmerksom på farene forbundet med

elektriske kretser, og kjenne til standardprosedyrer for å forhindre ulykker. Bruk nummeret i slutten

av hver advarsel for å finne oversettelsen i de oversatte sikkerhetsadvarslene som fulgte med denne

enheten.

TA VARE PÅ DISSE INSTRUKSJONENE

Aviso

INSTRUÇÕES IMPORTANTES DE SEGURANÇA

Este símbolo de aviso significa perigo. Você está em uma situação que poderá ser causadora de

lesões corporais. Antes de iniciar a utilização de qualquer equipamento, tenha conhecimento dos

perigos envolvidos no manuseio de circuitos elétricos e familiarize-se com as práticas habituais de

prevenção de acidentes. Utilize o número da instrução fornecido ao final de cada aviso para

localizar sua tradução nos avisos de segurança traduzidos que acompanham este dispositivo.

GUARDE ESTAS INSTRUÇÕES

¡Advertencia!

INSTRUCCIONES IMPORTANTES DE SEGURIDAD

Este símbolo de aviso indica peligro. Existe riesgo para su integridad física. Antes de manipular

cualquier equipo, considere los riesgos de la corriente eléctrica y familiarícese con los

procedimientos estándar de prevención de accidentes. Al final de cada advertencia encontrará el

número que le ayudará a encontrar el texto traducido en el apartado de traducciones que acompaña

a este dispositivo.

GUARDE ESTAS INSTRUCCIONES

Varning!

VIKTIGA SÄKERHETSANVISNINGAR

Denna varningssignal signalerar fara. Du befinner dig i en situation som kan leda till personskada.

Innan du utför arbete på någon utrustning måste du vara medveten om farorna med elkretsar och

känna till vanliga förfaranden för att förebygga olyckor. Använd det nummer som finns i slutet av

varje varning för att hitta dess översättning i de översatta säkerhetsvarningar som medföljer denna

anordning.

SPARA DESSA ANVISNINGAR

Send document comments to ucs-docfeedbac[email protected]

Cisco UCS B250 Extended Memory Blade Server Installation and Service Note

OL-22474-03

Send document comments to ucs-docfeedbac[email protected]

Cisco UCS B250 Extended Memory Blade Server Installation and Service Note

OL-22474-03

Aviso

INSTRUÇÕES IMPORTANTES DE SEGURANÇA

Este símbolo de aviso significa perigo. Você se encontra em uma situação em que há risco de lesões

corporais. Antes de trabalhar com qualquer equipamento, esteja ciente dos riscos que envolvem os

circuitos elétricos e familiarize-se com as práticas padrão de prevenção de acidentes. Use o

número da declaração fornecido ao final de cada aviso para localizar sua tradução nos avisos de

segurança traduzidos que acompanham o dispositivo.

GUARDE ESTAS INSTRUÇÕES

Advarsel

VIGTIGE SIKKERHEDSANVISNINGER

Dette advarselssymbol betyder fare. Du befinder dig i en situation med risiko for

legemesbeskadigelse. Før du begynder arbejde på udstyr, skal du være opmærksom på de

involverede risici, der er ved elektriske kredsløb, og du skal sætte dig ind i standardprocedurer til

undgåelse af ulykker. Brug erklæringsnummeret efter hver advarsel for at finde oversættelsen i de

oversatte advarsler, der fulgte med denne enhed.

GEM DISSE ANVISNINGER

Send document comments to ucs-docfeedbac[email protected]

Cisco UCS B250 Extended Memory Blade Server Installation and Service Note

OL-22474-03

Send document comments to ucs-docfeedbac[email protected]

Cisco UCS B250 Extended Memory Blade Server Installation and Service Note

OL-22474-03

Installing and Removing a Blade Server Hard Drive

There are up to 2 front-accessible, hot-swappable, 2.5-inch drives per blade. An LSI 1064E RAID

controller is embedded in the motherboard (it is not separately replaceable) and it supports RAID 0 and

1. You can remove blade server hard drives without removing the blade server from the chassis. All other

component replacement for a blade server requires removing the blade from the chassis. Unused hard

drive bays should always be covered with cover plates (N20-BBLKD) to assure proper cooling and

ventilation. The chassis is omitted from illustrations here to simplify the drawing.

Caution To prevent ESD damage, wear grounding wrist straps during these procedures and handle modules by

the carrier edges only.

Note Seagate SATA disks and Intel or Samsung SATA SSDs are not supported in UCS Manager release 1.2(1)

and cannot be used with servers using UCS Manager release 1.2(1).

Replacing an HDD or SSD with a drive of the same size, model, and manufacturer generally causes few

problems with UCS Manager. If the drive being replaced was part of a RAID array we recommend using

a newly ordered drive of identical size, model, and manufacturer to replace the failed drive. Cisco

recommends following industry standard practice of using drives of the same capacity when creating

RAID volumes. If drives of different capacities are used, the usable portion of the smallest drive will be

used on all drives that make up the RAID volume. Before upgrading or adding an HDD to a running

system, check the service profile in UCS Manager and make sure the new hardware configuration will

be within the parameters allowed by the service profile.

Hard disk and RAID troubleshooting information is in the “Troubleshooting Server Hardware” chapter

of the Cisco UCS Troubleshooting Guide.

Send document comments to ucs-docfeedbac[email protected]

Cisco UCS B250 Extended Memory Blade Server Installation and Service Note

OL-22474-03

Installing and Removing a Blade Server Hard Drive

Table 2 shows the drives supported in this blade server.

Removing a Blade Server Hard Drive

To remove a hard drive from a blade server, follow these steps:

Step 1 Push the button to release the ejector, and then pull the hard drive from its slot.

Step 2 Place the hard drive on an antistatic mat or antistatic foam if you are not immediately reinstalling it in

another blade server.

Step 3 Install a blank faceplate (N20-BBLKD) to keep dust out of the blade server if the slot will remain empty.

Table 2 Supported Hard Disk Drives (HDD)

Product ID Description

A03-D073GC2 73 GB 6Gb SAS transfer rate1, 15K RPM HDD/hot plug/drive sled mounted

1. The built-in 1064E RAID controller runs at 1.5Gb Link Speed instead of 3Gb with 6Gb Local Disks when running UCS 1.4(2) and earlier software

releases.

A03-D146GA2 146 GB 6Gb SAS transfer rate1, 10K RPM SFF HDD/hot plug/drive sled mounted

A03-D146GC2 146 GB 6Gb SAS transfer rate1, 10K RPM SFF HDD/hot plug/drive sled mounted

A03-D300GA2 300 GB, 6Gb SAS transfer rate1, 15K RPM HDD/hot plug/drive sled mounted

A03-D100SSD 100 GB SATA SSD HDD/hot plug/drive sled mounted (no longer sold)

A03-D600GA2 600 GB, 6Gb SAS transfer rate1, 10K RPM HDD/hot plug/drive sled mounted

A03-D500GC3 500GB 6Gb SATA 7.2K RPM SFF hot plug/drive sled mounted

UCS-SSD100GI1F104 100 GB Low-Height 7mm SATA SSD hot plug/drive sled mounted

A03-D1TBSATA 1 TB SATA 7.2K RPM SFF HDD /hot plug/drive sled mounted

UCS-HDD300GI2F105 300GB 6Gb SAS 15K RPM SFF HDD/hot plug/drive sled mounted2

2. This drive requires UCS capability catalog version 1.0.50.T or 2.0.1nT or later.

UCS-HDD900GI2F106 900GB 6Gb SAS 10K RPM SFF HDD/hot plug/drive sled mounted3

3. This drive requires UCS capability catalog version 1.0.54.T or 2.0.1pT or later.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Cisco Server Handbücher

Cisco

Cisco AS5300 - Universal Access Server Bedienungsanleitung

Cisco

Cisco UCS C420 Montage- und Wartungsanleitung

Cisco

Cisco UCS C220 M4 Bedienungsanleitung

Cisco

Cisco UCS C460 Bedienungsanleitung

Cisco

Cisco UCS C200 M2 Systemhandbuch

Cisco

Cisco SNS-3415 series Bedienungsanleitung

Cisco

Cisco UCS B200 M5 Handbuch

Cisco

Cisco UCS C220 M3 Bedienungsanleitung

Cisco

Cisco Sourcefire Defense Center 750 Bedienungsanleitung

Cisco

Cisco Firepower 1120 Bedienungsanleitung

Cisco

Cisco UCS 5100 Bedienungsanleitung

Cisco

Cisco UCS C240 M4 Montage- und Wartungsanleitung

Cisco

Cisco UCS C480 M5 Montage- und Wartungsanleitung

Cisco

Cisco UCS C3160 Montage- und Wartungsanleitung

Cisco

Cisco AS5200 - Universal Access Server Bedienungsanleitung

Cisco

Cisco C880 Series Montageanleitung

Cisco

Cisco Nexus 7000 Series Bedienungsanleitung

Cisco

Cisco UCS B200 M4 Handbuch

Cisco

Cisco C800 Series Betriebsanleitung

Cisco

Cisco ACE-4710-1F-K9 Bedienungsanleitung

Cisco

Cisco UCS X9508 Bedienungsanleitung

Cisco

Cisco TelePresence Server 7010 Referenzhandbuch

Cisco

Cisco C220 Handbuch

Cisco

Cisco UCS B440-M1 Bedienungsanleitung

Beliebte Server Handbücher anderer Marken

HP AlphaServer ES47 Bedienungsanleitung

Dell

Dell PowerEdge R410 Bedienungsanleitung

PowerNAS

PowerNAS CMA Bedienungsanleitung

Supero

Supero FatTwin F617R3-FT Bedienungsanleitung

MSI

MSI P1-109N-L70 Bedienungsanleitung

Dell

Dell PowerEdge XE9640 Handbuch

Dell

Dell PS4100 Montageanleitung

EtroVISION

EtroVISION EV3151 Bedienungsanleitung

NEC

NEC Express5800/T110j Bedienungsanleitung

HP ProLiant Gen9 Bedienungsanleitung

Compaq

Compaq ProLiant 3000 Handbuch

Dell

Dell PowerEdge 3YPMN Bedienungsanleitung

iRobo

iRobo IPC2U Bedienungsanleitung

Nortel

Nortel 1000 Con?guration guide Bedienungsanleitung

Asus

Asus AP7500 Bedienungs- und Wartungshandbuch

Avid Technology

Avid Technology AirSpeed 5000 Bedienungsanleitung

HP Integrity rx2600 Installationsanleitung

Milestone

Milestone Husky IVO 350T Bedienungsanleitung