Cisco UCS C220 M5 Bedienungsanleitung

Maintaining the Server

•Status LEDs and Buttons, on page 1

•Preparing For Component Installation, on page 6

•Removing and Replacing Components, on page 11

•Service Headers and Jumpers, on page 79

Status LEDs and Buttons

This section contains information for interpreting front, rear, and internal LED states.

Front-Panel LEDs

Figure 1: Front Panel LEDs

Table 1: Front Panel LEDs, Definition of States

StatesLED Name

Maintaining the Server

• Off—The hard drive is operating properly.

• Amber—Drive fault detected.

• Amber, blinking—The device is rebuilding.

• Amber, blinking with one-second interval—Drive

locate function activated in the software.

SAS/SATA drive fault

NVMe solid state drive (SSD) drive tray

LEDs have different behavior than

SAS/SATA drive trays.

Note

SAS

• Off—There is no hard drive in the hard drive tray (no

access, no fault).

• Green—The hard drive is ready.

•Green, blinking—The hard drive is reading or writing

data.

SAS/SATA drive activity LED2

SAS

• Off—The drive is not in use and can be safely

removed.

• Green—The drive is in use and functioning properly.

• Green, blinking—the driver is initializing following

insertion or the driver is unloading following an eject

command.

• Amber—The drive has failed.

• Amber, blinking—A drive Locate command has been

issued in the software.

NVMe SSD drive fault

NVMe solid state drive (SSD) drive tray

LEDs have different behavior than

SAS/SATA drive trays.

Note

NVMe

• Off—No drive activity.

• Green, blinking—There is drive activity.

NVMe SSD activity2

NVMe

• Off—There is no AC power to the server.

•Amber—The server is in standby power mode. Power

is supplied only to the Cisco IMC and some

motherboard functions.

• Green—The server is in main power mode. Power is

supplied to all server components.

Power button/LED3

• Off—The unit identification function is not in use.

• Blue, blinking—The unit identification function is

activated.

Unit identification4

Maintaining the Server

Front-Panel LEDs

• Green—The server is running in normal operating

condition.

• Green, blinking—The server is performing system

initialization and memory check.

• Amber, steady—The server is in a degraded

operational state (minor fault). For example:

• Power supply redundancy is lost.

• CPUs are mismatched.

• At least one CPU is faulty.

• At least one DIMM is faulty.

•At least one drive in a RAID configuration failed.

• Amber, 2 blinks—There is a major fault with the

system board.

• Amber, 3 blinks—There is a major fault with the

memory DIMMs.

• Amber, 4 blinks—There is a major fault with the

CPUs.

System health5

• Green—All power supplies are operating normally.

• Amber, steady—One or more power supplies are in

a degraded operational state.

• Amber, blinking—One or more power supplies are

in a critical fault state.

Power supply status6

• Green—All fan modules are operating properly.

•Amber, blinking—One or more fan modules breached

the non-recoverable threshold.

Fan status7

• Off—The Ethernet LOM port link is idle.

• Green—One or more Ethernet LOM ports are

link-active, but there is no activity.

• Green, blinking—One or more Ethernet LOM ports

are link-active, with activity.

Network link activity8

•Green—The server is operating at normal temperature.

• Amber, steady—One or more temperature sensors

breached the critical threshold.

• Amber, blinking—One or more temperature sensors

breached the non-recoverable threshold.

Temperature status9

Maintaining the Server

Front-Panel LEDs

Rear-Panel LEDs

Figure 2: Rear Panel LEDs

Table 2: Rear Panel LEDs, Definition of States

StatesLED Name

• Amber—Link speed is 100 Mbps.

• Amber—Link speed is 1 Gbps.

• Green—Link speed is 10 Gbps.

1-Gb/10-Gb Ethernet link speed (on both LAN1 and

LAN2)

• Off—No link is present.

• Green—Link is active.

• Green, blinking—Traffic is present on the active link.

1-Gb/10-Gb Ethernet link status (on both LAN1 and

LAN2)

• Off—Link speed is 10 Mbps.

• Amber—Link speed is 100 Mbps.

• Green—Link speed is 1 Gbps.

1-Gb Ethernet dedicated management link speed3

• Off—No link is present.

• Green—Link is active.

• Green, blinking—Traffic is present on the active link.

1-Gb Ethernet dedicated management link status4

• Off—The unit identification function is not in use.

• Blue, blinking—The unit identification function is

activated.

Rear unit identification5

Maintaining the Server

Rear-Panel LEDs

AC power supplies:

• Off—No AC input (12 V main power off, 12 V

standby power off).

• Green, blinking—12 V main power off; 12 V standby

power on.

• Green, solid—12 V main power on; 12 V standby

power on.

• Amber, blinking—Warning threshold detected but 12

V main power on.

• Amber, solid—Critical error detected; 12 V main

power off (for example, over-current, over-voltage,

or over-temperature failure).

DC power supplies:

• Off—No DC input (12 V main power off, 12 V

standby power off).

• Green, blinking—12 V main power off; 12 V standby

power on.

• Green, solid—12 V main power on; 12 V standby

power on.

• Amber, blinking—Warning threshold detected but 12

V main power on.

• Amber, solid—Critical error detected; 12 V main

power off (for example, over-current, over-voltage,

or over-temperature failure).

Power supply status (one LED each power supply unit)6

Internal Diagnostic LEDs

The server has internal fault LEDs for CPUs, DIMMs, and fan modules.

Maintaining the Server

Internal Diagnostic LEDs

Figure 3: Internal Diagnostic LED Locations

DIMM fault LEDs (one behind each DIMM socket

on the motherboard)

These LEDs operate only when the server is in

standby power mode.

• Amber—DIMM has a fault.

• Off—DIMM is OK.

3Fan module fault LEDs (one behind each fan

connector on the motherboard)

• Amber—Fan has a fault or is not fully seated.

• Green—Fan is OK.

-CPU fault LEDs (one behind each CPU socket on

the motherboard).

These LEDs operate only when the server is in

standby power mode.

• Amber—CPU has a fault.

• Off—CPU is OK.

Preparing For Component Installation

This section includes information and tasks that help prepare the server for component installation.

Required Equipment For Service Procedures

The following tools and equipment are used to perform the procedures in this chapter:

Maintaining the Server

Preparing For Component Installation

• T-30 Torx driver (supplied with replacement CPUs for heatsink removal)

• #1 flat-head screwdriver (supplied with replacement CPUs for heatsink removal)

• #1 Phillips-head screwdriver (for M.2 SSD and intrusion switch replacement)

• Electrostatic discharge (ESD) strap or other grounding equipment such as a grounded mat

Shutting Down and Removing Power From the Server

The server can run in either of two power modes:

• Main power mode—Power is supplied to all server components and any operating system on your drives

can run.

• Standby power mode—Power is supplied only to the service processor and certain components. It is safe

for the operating system and data to remove power cords from the server in this mode.

After a server is shut down to standby power, electric current is still present in the server. To completely

remove power as directed in some service procedures, you must disconnect all power cords from all power

supplies in the server.

Caution

You can shut down the server by using the front-panel power button or the software management interfaces.

Shutting Down Using the Power Button

Step 1 Check the color of the Power button/LED:

• Amber—The server is already in standby mode and you can safely remove power.

• Green—The server is in main power mode and must be shut down before you can safely remove power.

Step 2 Invoke either a graceful shutdown or a hard shutdown:

To avoid data loss or damage to your operating system, you should always invoke a graceful shutdown of the

operating system.

Caution

• Graceful shutdown—Press and release the Power button. The operating system performs a graceful shutdown and

the server goes to standby mode, which is indicated by an amber Power button/LED.

• Emergency shutdown—Press and hold the Power button for 4 seconds to force the main power off and immediately

enter standby mode.

Step 3 If a service procedure instructs you to completely remove power from the server, disconnect all power cords from the

power supplies in the server.

Shutting Down Using The Cisco IMC GUI

You must log in with user or admin privileges to perform this task.

Maintaining the Server

Shutting Down and Removing Power From the Server

Step 1 In the Navigation pane, click the Server tab.

Step 2 On the Server tab, click Summary.

Step 3 In the Actions area, click Power Off Server.

Step 4 Click OK.

The operating system performs a graceful shutdown and the server goes to standby mode, which is indicated by an amber

Power button/LED.

Step 5 If a service procedure instructs you to completely remove power from the server, disconnect all power cords from the

power supplies in the server.

Shutting Down Using The Cisco IMC CLI

You must log in with user or admin privileges to perform this task.

Step 1 At the server prompt, enter:

Example:

server# scope chassis

Step 2 At the chassis prompt, enter:

Example:

server/chassis# power shutdown

The operating system performs a graceful shutdown and the server goes to standby mode, which is indicated by an amber

Power button/LED.

Step 3 If a service procedure instructs you to completely remove power from the server, disconnect all power cords from the

power supplies in the server.

Shutting Down Using The Cisco UCS Manager Equipment Tab

You must log in with user or admin privileges to perform this task.

Step 1 In the Navigation pane, click Equipment.

Step 2 Expand Equipment > Rack Mounts > Servers.

Step 3 Choose the server that you want to shut down.

Step 4 In the Work pane, click the General tab.

Step 5 In the Actions area, click Shutdown Server.

Step 6 If a confirmation dialog displays, click Yes.

The operating system performs a graceful shutdown and the server goes to standby mode, which is indicated by an amber

Power button/LED.

Maintaining the Server

Shutting Down Using The Cisco IMC CLI

Step 7 If a service procedure instructs you to completely remove power from the server, disconnect all power cords from the

power supplies in the server.

Shutting Down Using The Cisco UCS Manager Service Profile

You must log in with user or admin privileges to perform this task.

Step 1 In the Navigation pane, click Servers.

Step 2 Expand Servers > Service Profiles.

Step 3 Expand the node for the organization that contains the service profile of the server that you are shutting down.

Step 4 Choose the service profile of the server that you are shutting down.

Step 5 In the Work pane, click the General tab.

Step 6 In the Actions area, click Shutdown Server.

Step 7 If a confirmation dialog displays, click Yes.

The operating system performs a graceful shutdown and the server goes to standby mode, which is indicated by an amber

Power button/LED.

Step 8 If a service procedure instructs you to completely remove power from the server, disconnect all power cords from the

power supplies in the server.

Removing the Server Top Cover

Step 1 Remove the top cover:

a) If the cover latch is locked, use a screwdriver to turn the lock 90-degrees counterclockwise to unlock it.

b) Lift on the end of the latch that has the green finger grip. The cover is pushed back to the open position as you lift

the latch.

c) Lift the top cover straight up from the server and set it aside.

Step 2 Replace the top cover:

a) With the latch in the fully open position, place the cover on top of the server about one-half inch (1.27 cm) behind

the lip of the front cover panel. The opening in the latch should fit over the peg that sticks up from the fan tray.

b) Press the cover latch down to the closed position. The cover is pushed forward to the closed position as you push

down the latch.

c) If desired, lock the latch by using a screwdriver to turn the lock 90-degrees clockwise.

Maintaining the Server

Shutting Down Using The Cisco UCS Manager Service Profile

Figure 4: Removing the Top Cover

Locking cover latch2Top cover1

Serial number label location3

Serial Number Location

The serial number for the server is printed on a label on the top of the server, near the front. See Removing

the Server Top Cover, on page 9.

Hot Swap vs Hot Plug

Some components can be removed and replaced without shutting down and removing power from the server.

This type of replacement has two varieties: hot-swap and hot-plug.

• Hot-swap replacement—You do not have to shut down the component in the software or operating

system. This applies to the following components:

Maintaining the Server

Serial Number Location

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Cisco Server Handbücher

Cisco

Cisco UCS C460 M4 Installations- und Betriebshandbuch

Cisco

Cisco UCS C200 Montage- und Wartungsanleitung

Cisco

Cisco UCS B200 M4 Installations- und Betriebshandbuch

Cisco

Cisco ISE-3315 Bedienungsanleitung

Cisco

Cisco Firepower Management Center 750 Bedienungsanleitung

Cisco

Cisco UCS C210 M2 Systemhandbuch

Cisco

Cisco expressway ce1100 Bedienungsanleitung

Cisco

Cisco TelePresence Bedienungsanleitung

Cisco

Cisco ONS 15600 Bedienungsanleitung

Cisco

Cisco UCS C460 Bedienungsanleitung

Cisco

Cisco UCS C Series Bedienungsanleitung

Cisco

Cisco C880 M5 Bedienungsanleitung

Cisco

Cisco 7513 Series Leitfaden

Cisco

Cisco UCS B460 M4 Handbuch

Cisco

Cisco UCS B Series Installations- und Betriebshandbuch

Cisco

Cisco UCS X210c M6 Handbuch

Cisco

Cisco TelePresenceMCU 5300 Series Bedienungsanleitung

Cisco

Cisco ONS 15454 SONET Bedienungsanleitung

Cisco

Cisco TelePresence Service-Handbuch

Cisco

Cisco UCS E Series Handbuch

Cisco

Cisco ONS 15454 Handbuch

Cisco

Cisco UCS C240 M3 Bedienungsanleitung

Cisco

Cisco 700 series Installations- und Betriebshandbuch

Cisco

Cisco SNS-3415 series Bedienungsanleitung

Beliebte Server Handbücher anderer Marken

HP AlphaServer ES47 Bedienungsanleitung

Dell

Dell PowerEdge R410 Bedienungsanleitung

PowerNAS

PowerNAS CMA Bedienungsanleitung

Supero

Supero FatTwin F617R3-FT Bedienungsanleitung

MSI

MSI P1-109N-L70 Bedienungsanleitung

Dell

Dell PowerEdge XE9640 Handbuch

Dell

Dell PS4100 Montageanleitung

EtroVISION

EtroVISION EV3151 Bedienungsanleitung

NEC

NEC Express5800/T110j Bedienungsanleitung

HP ProLiant Gen9 Bedienungsanleitung

Compaq

Compaq ProLiant 3000 Handbuch

Dell

Dell PowerEdge 3YPMN Bedienungsanleitung

iRobo

iRobo IPC2U Bedienungsanleitung

Nortel

Nortel 1000 Con?guration guide Bedienungsanleitung

Asus

Asus AP7500 Bedienungs- und Wartungshandbuch

Avid Technology

Avid Technology AirSpeed 5000 Bedienungsanleitung

HP Integrity rx2600 Installationsanleitung

Milestone

Milestone Husky IVO 350T Bedienungsanleitung