Cisco Aironet 1250 Series Bedienungsanleitung

Quick Start Guide: Cisco Aironet 1250 Series Access Point

Read This First

This guide is designed to help you prepare your Cisco Aironet 1250 Series

Access Point (hereafter referred to as the access point) for use on your

wireless network. This section contains important information on what you

you need to know so that you can successfully prepare and deploy your access

point.

The default login and password used to access the access point GUI or CLI is

Cisco. The password and login is case sensitive.

Removing the Mounting Plate

The access point ships with the mounting plate attached. You must remove the

plate before you can connect the power and Ethernet cables and access the

console port.

After unpacking the access point, follow these steps to remove the mounting

plate.

78-17831-01

Step 1 Grasp the access point with both hands as shown in the illustration

below.

231161

Quick Start Guide: Cisco Aironet 1250 Series Access Point

Step 2 With your right thumb or forefinger, pull the security hasp toward

you to release it from the mounting plate.

Step 3 Maintain pressure on the security hasp, use your thumb or

forefinger to push the mounting plate to the right, and slide it off the

mounting plate pins.

Step 4 Remove the mounting plate from the access point.

Radio and IP Address Configuration

The access point ships with its radios disabled and no assigned IP address or

service set identifier (SSID). You must enable the radios when you configure

the access point for the first time. Also, the access point no longer is assigned

a default IP address. It is configured to obtain an IP address using a DHCP

server. If your network does not use a DHCP server, you must connect to the

access point’s console port and assign a static IP address. See the “Obtaining

and Assigning an IP Address” section on page 18.

Bridging Feature Not Tested

The 1250 series access point has not been tested for bridging purposes, even

though the commands for configuring the unit as a bridge are available.

78-17831-01

Before You Start

Because the configuration process varies depending on how you intend to use

your access point, detailed configuration instructions are not discussed in this

guide.

Configuration instructions specific to your intended use are covered in the

“Configuring the Access Point for the First Time” chapter of the Cisco IOS

Software Configuration Guide for Cisco Aironet Access Points.

We also recommend that you have the following documents available:

•Cisco IOS Software Configuration Guide for Cisco Aironet Access

Points—provides detailed information for advanced configurations.

•Cisco Aironet Command Reference for Cisco Aironet Access Points and

Bridges—lists all Cisco IOS commands with descriptions and syntax

instructions.

•Cisco Aironet 1250 Series Access Point Hardware Installation

Guide—provides mounting instructions, compliance information, and

technical specifications.

•Release Notes for Cisco Aironet Access Points for Cisco IOS Release

12.4(3g)JA (or later)—provides system requirements, new feature

descriptions, important notes, limitations, and last-minute updates.

Quick Start Guide: Cisco Aironet 1250 Series Access Point

These documents are also available on cisco.com. Follow this link:

http://www.cisco.com/en/US/products/ps6973/tsd_products_support_series_

home.html

Make sure that you are using a computer connected to the same network as

the access point, and obtain the following information from your network

administrator:

•A host name for the access point.

•The case-sensitive SSID for your 802.11 radio network.

•A Simple Network Management Protocol (SNMP) community name and

the SNMP file attribute (if SNMP is in use).

•The Media Access Control (MAC) address from the label on the bottom

of the access point (such as 0016462584c), if you plan to use the Cisco

IP Setup Utility to find an access point IP address.

•If you are not connected to a DHCP server, you can assign an IP address

to the access point using the CLI. In this situation, obtain a unique IP

address for your access point, a default gateway, and subnet mask from

your network system administrator.

78-17831-01

Safety Information

The FCC with its action in ET Docket 96-8 has adopted a safety standard for

human exposure to radio frequency (RF) electromagnetic energy emitted by

FCC certified equipment. When used with approved Cisco Aironet antennas,

Cisco Aironet products meet the uncontrolled environmental limits found in

OET-65 and ANSI C95.1, 1991.

Proper installation of this radio according to the instructions found in this

manual will result in user exposure that is substantially below the FCC

recommended limits.

•Do not hold any component containing a radio so that the antenna is very

close to or touching any exposed parts of the body, especially the face or

eyes, while transmitting.

•The use of wireless devices in hazardous locations is limited to the

constraints posed by the safety directors of such environments.

Warnings

Translated versions of the following safety warnings are provided in the

Safety Warnings for Cisco Aironet 1250 Series Access Points document that

ships with the access point.

Quick Start Guide: Cisco Aironet 1250 Series Access Point

Warning

Read the installation instructions before you connect the

system to its power source.

Statement 1004

Warning

This product relies on the building’s installation for

short-circuit (overcurrent) protection. Ensure that the

protective device is rated not greater than:

20A

Statement 1005

Warning

Do not operate your wireless network device near unshielded

blasting caps or in an explosive environment unless the

device has been modified to be especially qualified for such

use.

Statement 245B

Warning

In order to comply with FCC radio frequency (RF) exposure

limits, antennas should be located at a minimum of 7.9 inches

(20 cm) or more from the body of all persons.

Statement 332

78-17831-01

Unpacking the Access Point

Package Contents

Each access point package contains the following items:

•Cisco Aironet 1250 series autonomous access point

•Mounting hardware kit

–

– One mounting plate, two 4 x 40 x 3/16 in screws, and a mounting

plate latch (all attached to the access point)

–

– Two suspended ceiling T-rail clips, spacers (accommodates

standard and recessed T-rails), and nuts

–

– Four 8 x 18 x 3/4 in pan head Phillips sheet metal screws

–

– Four #8 plastic wall anchors

–

– One 10 x 24 nut (for ground stud on the mounting plate)

–

– Two cable tie wraps

•Product quick start guide

•Product translated safety warning document

•Cisco product registration card

Follow these steps to unpack the access point:

Quick Start Guide: Cisco Aironet 1250 Series Access Point

Step 1 Open the shipping container and carefully remove the contents.

Step 2 Return all packing materials to the shipping container and save it.

Step 3 Ensure that all items listed in the Package Contents section are

included in the shipment. Check each item for damage. If any item

is damaged or missing, notify your authorized Cisco sales

representative.

Note The access point has two radio module slots: Slot 0 and Slot 1. Slot

0 can only be used with the 2.4-GHz radio module and slot 1 can

only be used with the 5-GHz radio module. New radio configuration

changes are associated with the specific module slot where the radio

module is located. Once the default radio settings are changed, the

radio modules should not be moved to a different slot. If you move

the radio to a different slot, the radio configuration must be deleted

and then remade.

78-17831-01

Before Beginning the Installation

Before you begin the installation, refer to the illustrations on the following

pages to become familiar with the access point and the mounting hardware

Caution Be careful when handling the access point; the bottom plate

might be hot.

Caution The access point must be located indoors within the same

building, including the associated LAN connections.

The following illustrations show the access point and identify its features.

Andere Handbücher für Aironet 1250 Series

Inhaltsverzeichnis

Andere Cisco Drahtloser Zugangspunkt Handbücher

Cisco

Cisco Meraki MR36H Bedienungsanleitung

Cisco

Cisco AP541N-A-K9 Bedienungsanleitung

Cisco

Cisco Catalyst 9124AX Series Handbuch

Cisco

Cisco Linksys WAP54GX Original Betriebsanleitung

Cisco

Cisco Aironet 1200 Series Bedienungsanleitung

Cisco

Cisco Meraki MR42 Bedienungsanleitung

Cisco

Cisco Aironet 1570 Series Handbuch

Cisco

Cisco WAP131 Bedienungsanleitung

Cisco

Cisco Meraki Go GR12 Bedienungsanleitung

Cisco

Cisco ASR 1001 Handbuch

Cisco

Cisco Wap581 Bedienungsanleitung

Cisco

Cisco WAP121 Bedienungsanleitung

Cisco

Cisco Catalyst 9120AX Series Bedienungsanleitung

Cisco

Cisco MERAKI MR66 Bedienungsanleitung

Cisco

Cisco Small Business AP541N Bedienungsanleitung

Cisco

Cisco WAP4410N - Small Business Wireless-N Access... Bedienungsanleitung

Cisco

Cisco Meraki MR33 Bedienungsanleitung

Cisco

Cisco AIR-AP1832I K9C Series Bedienungsanleitung

Cisco

Cisco Aironet 1815w Bedienungsanleitung

Cisco

Cisco WAP571 Bedienungsanleitung

Cisco

Cisco 1142 - Aironet Standalone AP Bedienungsanleitung

Cisco

Cisco Aironet 1140 Series Bedienungsanleitung

Cisco

Cisco Aironet 1520 Series Bedienungsanleitung

Cisco

Cisco Aironet 1815T Bedienungsanleitung

Beliebte Drahtloser Zugangspunkt Handbücher anderer Marken

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Bedienungsanleitung

Ubiquiti

Ubiquiti NanoStation NSM2 Bedienungsanleitung

Aruba

Aruba IAP-335 Bedienungsanleitung

Advantek Networks

Advantek Networks AWN-AP-54MR Bedienungsanleitung

IP-COM

IP-COM AP355 Bedienungsanleitung

Buffalo

Buffalo AirStation WLA-L11G Bedienungsanleitung

EnGenius

EnGenius EnStationACv2 Bedienungsanleitung

D-Link

D-Link DAP-3662 Bedienungsanleitung

Widelink

Widelink ezWave WAP-1100 Series Bedienungsanleitung

Edimax

Edimax CAP1200 Bedienungsanleitung

xG Technology

xG Technology xMax CN1300 Bedienungsanleitung

Ubiquiti

Ubiquiti LBE-5AC-Gen2 Bedienungsanleitung

Aruba

Aruba AP-203R Bedienungsanleitung

LuXout Shades

LuXout Shades LUXSHADE MOTION Bedienungsanleitung

CreatComm

CreatComm TB5F Bedienungsanleitung

SineDigital

SineDigital MW-1500AP(H) Bedienungsanleitung

TP-Link

TP-Link AP9650 V1 Bedienungsanleitung

Draytek

Draytek VIGORAP 902 Bedienungsanleitung