Cisco WAP571 Bedienungsanleitung

●

Manually Connect a WAP571 or WAP571E to

the Network via Power Over Ethernet (PoE)

Objective

Connecting a Wireless Access Point (WAP) to the same network as your computer would allow

them to communicate, thus, allowing you to configure the WAP. This is typically done when the

WAP is to be configured for the first time, or after the WAP has been reset, and will have to be

reconfigured. This article aims to show you the steps in connecting the WAP571 or WAP571E to

the network.

Applicable Devices

WAP500 Series – WAP571, WAP571E

Software Version

1.0.0.15 – WAP571, WAP571E

Connect the WAP571 to the Network via PoE

Important: Make sure that the network you are connecting the WAP to has PoE (802.3af and

802.3at) and that your network is up and running.

Step 1. Connect one end of an Ethernet cable to the Ethernet port of a PoE switch, or router.

Step 2. Connect the other end of the Ethernet cable to the ETH0/PD port of the WAP571.

Note: WAP571 bundles the two Ethernet ports to be in link aggregation mode. If the two Ethernet

ports have been connected at the same time, the link partner must also support link aggregation.

Step 3. Check the lights on both the WAP571 and the PoE switch, or router.

Note:

An orange light on the port of the PoE switch where the WAP571 is connected indicates that

the PoE switch is powering the WAP571.

A green light on the Ethernet port of the PoE switch where the WAP571 is connected

indicates a link between the devices.

A blinking green light on the front panel of the WAP571 indicates that the device is booting up.

A solid green light indicates that the WAP571 is ready and operational.

A solid green light on the Ethernet port of the WAP571 indicates a link between the switch and

the WAP571.

A blinking green light on the Ethernet port of the WAP571 indicates that the device is

receiving and transmitting data.

You should now have connected your WAP571E to the network via PoE and can now proceed to

setting up the access point. For instructions, see Configure Basic Radio Settings on the WAP571

or WAP571E Wireless Access Point.

Connect the WAP571E to the Network via PoE

Prepare the Cabling

Step 1. Disassemble the weather-proof connector to expose the red rubber gasket. After

disassembling, you should have the following:

1 Thick rubber gasket1. Part B of the weather-proof connector2. Thin rubber gasket3. Part A of the weather-proof connector4.

Step 2. Slide the Ethernet cable through Part B of the weather-proof connector.

Step 3. Pinch the thick rubber gasket to reveal the cut and then slide the Ethernet cable through

the cut.

Step 4. Slide the Ethernet cable through Part A of the weather-proof connector.

Step 5. Insert the thin red gasket into the opening of Part B of the weather-proof connector.

Connect the WAP571E via PoE

Important: Make sure that the network you are connecting the WAP to has PoE (802.3af and

802.3at) and that your network is up and running.

Step 1. Go over the back and bottom panels of the WAP571E.

Step 2. Position the WAP571E in such a way that the label underneath the device is right side up.

Step 3. Remove the cover of the port labeled ETH0/PD to expose the Ethernet port. This can be

done by turning the cap counter-clockwise.

Note: Take care not to lose the thin rubber gasket.

Step 4. Connect the Ethernet cable into the ETH0/PD slot of the WAP571E.

Step 5. Secure the weather-proof connector by turning it clockwise on to the threaded portion of

the WAP571E.

Step 6. Insert the thick rubber gasket into Part B of the weather-proof connector.

Step 7. Secure Part A of the weather-proof connector by turning it clockwise on to the threaded

portion of Part B.

Step 8. Connect the other end of the Ethernet cable to the Ethernet port of the PoE switch.

Step 9. Check the lights on both the WAP571E and the PoE switch.

Verify the WAP571/WAP571E with PoE Connection

To verify the hardware installation, follow these instructions:

Check the cable connections.

●

Check the indicator lights.

●

Label Activity Description

Power

Off The access point is off

Solid (Green) The access point is normal; No wireless client is

connected

Solid (Blue) The access point is normal; at least one wireless

client is connected

Flashing (Blue) The access point is upgrading the firmware.

Solid (Red) The access point fails to boot with both firmware

images.

LAN

(WAP571)

Off No Ethernet link; FE Ethernet link is active or 10

Mbps.

Solid Green GE Ethernet link is active.

Flashing Green The access point is transmitting or receiving data.

You should now have connected your WAP571E to the network via PoE and can now proceed to

setting up the access point. For instructions, see Configure Basic Radio Settings on the WAP571

or WAP571E Wireless Access Point.

Andere Handbücher für WAP571

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Cisco Drahtloser Zugangspunkt Handbücher

Cisco

Cisco Linksys WAP610N Bedienungsanleitung

Cisco

Cisco Meraki MR84 Handbuch

Cisco

Cisco 1130AG - Aironet - Wireless Access Point Handbuch

Cisco

Cisco Meraki MR36 Bedienungsanleitung

Cisco

Cisco Aironet 1140 Series Bedienungsanleitung

Cisco

Cisco Aironet 1570 Series Bedienungsanleitung

Cisco

Cisco AIR-MP20B Bedienungsanleitung

Cisco

Cisco Aironet 1815w Bedienungsanleitung

Cisco

Cisco Linksys WAP55AG Bedienungsanleitung

Cisco

Cisco aironet 1522 Leitfaden

Cisco

Cisco AIR-AP352E2R - Aironet 350 - Wireless Access... Bedienungsanleitung

Cisco

Cisco Aironet 1520 Series Handbuch

Cisco

Cisco Aironet 2600 Series Bedienungsanleitung

Cisco

Cisco Small Business WAP44 Bedienungsanleitung

Cisco

Cisco AIR-AP1120B-A-K9 - Aironet 1100 Series Access... Handbuch

Cisco

Cisco Aironet 1250 Series Bedienungsanleitung

Cisco

Cisco Aironet 1240AG Series Handbuch

Cisco

Cisco FM PONTE-50 Handbuch

Cisco

Cisco WAP121 Bedienungsanleitung

Cisco

Cisco Aironet 1040 Series Bedienungsanleitung

Cisco

Cisco AIR-AP1232AG-A-K9 - Aironet 1230AG - Wireless Access... Bedienungsanleitung

Cisco

Cisco Meraki MR28 Bedienungsanleitung

Cisco

Cisco WAP300N Bedienungsanleitung

Cisco

Cisco AIR-LAP1310G Bedienungsanleitung

Beliebte Drahtloser Zugangspunkt Handbücher anderer Marken

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Bedienungsanleitung

Ubiquiti

Ubiquiti NanoStation NSM2 Bedienungsanleitung

Aruba

Aruba IAP-335 Bedienungsanleitung

Advantek Networks

Advantek Networks AWN-AP-54MR Bedienungsanleitung

IP-COM

IP-COM AP355 Bedienungsanleitung

Buffalo

Buffalo AirStation WLA-L11G Bedienungsanleitung

EnGenius

EnGenius EnStationACv2 Bedienungsanleitung

D-Link

D-Link DAP-3662 Bedienungsanleitung

xG Technology

xG Technology xMax CN1300 Bedienungsanleitung

Widelink

Widelink ezWave WAP-1100 Series Bedienungsanleitung

Edimax

Edimax CAP1200 Bedienungsanleitung

Ubiquiti

Ubiquiti LBE-5AC-Gen2 Bedienungsanleitung

Aruba

Aruba AP-203R Bedienungsanleitung

LuXout Shades

LuXout Shades LUXSHADE MOTION Bedienungsanleitung

CreatComm

CreatComm TB5F Bedienungsanleitung

SineDigital

SineDigital MW-1500AP(H) Bedienungsanleitung

TP-Link

TP-Link AP9650 V1 Bedienungsanleitung

Draytek

Draytek VIGORAP 902 Bedienungsanleitung