Cisco Aironet 2600 Series Bedienungsanleitung

GETTING STARTED GUIDE

Cisco Aironet 2600 Series Access Points

January, 2013

P/N: 78-20842-01

1About this Guide

2Introduction to the Access Point

3Safety Instructions

4Unpacking

5Configurations

6Access Point Ports and Connectors

7Configuring the Access Point

8Mounting the Access Point

9Deploying the Access Point on the Wireless Network

10 Troubleshooting

11 Declarations of Conformity and Regulatory Information

12 Configuring DHCP Option 43 and DHCP Option 60

13 Access Point Specifications

1 About this Guide

This Guide provides instructions on how to install and configure your Cisco Aironet 2600 Series

Access Point. The 2600 Series Access Point is referred to as the 2600 series or the access point in this

document.

2 Introduction to the Access Point

The 2600 series supports high-performing Spectrum Intelligence which sustains three spatial stream

rates over a deployable distance with high reliability when serving clients. The 2600 series provides

high reliability and overall wireless performance.

The 2600 series offers dual-band radios (2.4 GHz and 5 GHz) with integrated and external antenna

options. The access points support full inter-operability with leading 802.11n clients, and support a

mixed deployment with other access points and controllers.

The 2600 series access point is available in both controller-based (Unified) and standalone

(Autonomous) configurations and supports:

•Simultaneous single-band or dual-band (2.4 GHz/5 GHz) radios

•Integrated antennas on 2602I access point models (AIR-CAP2602I-x-K9)

•External antennas for rugged 2602E access point models (AIR-CAP2602E-x-K9)

Note The ‘x’ in the model numbers represents the regulatory domain. Refer to “Regulatory

Domains” section on page 6 for a list of supported regulatory domains.

The features of the 2600 series are:

•Processing sub-systems (including CPUs and memory) and radio hardware which supports:

–

Network management

–

CleanAir—Automatic detection, classification, location and mitigation of RF interference

(not available on autonomous or standalone models)

–

ClientLink 2.0—BeamForming to 802.11n clients as well as legacy 802.11a/g OFDM clients

–

VideoStream (available only in WGB mode for autonomous or standalone models)

–

Location (not available on autonomous or standalone models)

–

WIDS/WIPS (not available on autonomous or standalone models)

–

Security

–

Radio Resource Management (RRM) (not available on autonomous or standalone models)

–

Rogue detection (not available on autonomous or standalone models)

–

Management Frame Protection (MFP) (not available on autonomous or standalone models)

–

BandSelect (not available on autonomous or standalone models)

–

Throughput, forwarding, and filtering performance scaled to meet 3 spatial stream, 450 Mbps

data-rates

•32 MB flash size

•802.11af/at

–

CDP (Cisco Discovery Protocol)

•2.4 GHz and 5 GHz 802.11n radios with the following features:

–

3TX x 4RX

–

3-spatial streams, 450 Mbps PHY rate

–

Spectrum intelligence

–

DPD (Digital Pre-Distortion) technology

–

Cisco Vector Beamforming—Implicit Co-phase beamforming for .11ag clients and 1

spatial-stream and 2 spatial-stream clients

–

Radio hardware is capable of explicit compressed beamforming (ECBF) per 802.11n standard

3 Safety Instructions

Translated versions of the following safety warnings are provided in the translated safety warnings

document that is shipped with your access point. The translated warnings are also in the Translated

Safety Warnings for Cisco Aironet Access Points, which is available on Cisco.com.

Warning

IMPORTANT SAFETY INSTRUCTIONS

This warning symbol means danger. You are in a situation that could cause bodily injury.

Before you work on any equipment, be aware of the hazards involved with electrical

circuitry and be familiar with standard practices for preventing accidents. Use the

statement number provided at the end of each warning to locate its translation in the

translated safety warnings that accompanied this device.

Statement 1071

SAVE THESE INSTRUCTIONS

Warning

Read the installation instructions before you connect the system to its power source.

Statement 1004

Warning

Installation of the equipment must comply with local and national electrical codes.

Statement 1074

Warning

This product relies on the building’s installation for short-circuit (overcurrent)

protection. Ensure that the protective device is rated not greater than:

20A.

Statement 1005

Warning

Do not operate your wireless network device near unshielded blasting caps or in an

explosive environment unless the device has been modified to be especially qualified for

such use.

Statement 245B

Warning

In order to comply with FCC radio frequency (RF) exposure limits, antennas should be

located at a minimum of 7.9 inches (20 cm) or more from the body of all persons.

Statement 332

Caution The fasteners you use to mount an access point on a ceiling must be capable of

maintaining a minimum pullout force of 20 lbs (9 kg) and must use all 4 indented holes

on the mounting bracket.

Caution This product and all interconnected equipment must be installed indoors within the same

building, including the associated LAN connections as defined by Environment A of the

IEEE 802.af Standard.

Note The access point is suitable for use in environmental air space in accordance with section

300.22.C of the National Electrical Code and sections 2-128, 12-010(3), and 12-100 of the

Canadian Electrical Code, Part 1, C22.1. You should not install the power supply or power

injector in air handling spaces.

Note Use only with listed ITE equipment.

4 Unpacking

To unpack the access point, follow these steps:

Step 1 Unpack and remove the access point and the accessory kit from the shipping box.

Step 2 Return any packing material to the shipping container and save it for future use.

Step 3 Verify that you have received the items listed below. If any item is missing or damaged, contact

your Cisco representative or reseller for instructions.

–

The access point

–

Mounting bracket (selected when you ordered the access point)

–

Adjustable ceiling-rail clip (selected when you ordered the access point)

5 Configurations

The 2600 series access point contains two simultaneous dual-band radios, the 2.4-GHz and 5-GHz

802.11n MIMO radios, in either controller-based mode (AIR-CAP2602 models) or standalone mode

(AIR-SAP2602 models). The 2600 series access point configurations are:

•AIR-CAP2602E-x-K9 and AIR-SAP2602E-x-K9—two 2.4-GHz/5-GHz dual-band radios with up

to 4 external dual-band dipole antennas

•AIR-CAP2602I-x-K9 and AIR-SAP2602I-x-K9—two 2.4-GHz/5-GHz dual-band radios, with

integrated dual-band inverted-F antennas

For information on the regulatory domains (shown as “x” in the model numbers) see “Regulatory

Domains” section on page 6.

External Antennas

The 2602E models are configured with up to four external dual-band dipole antennas, and two

2.4-GHz/5-GHz dual-band radios. The radios and antennas support frequency bands 2400–2500

MHz and 5150–5850 MHz through a common dual-band RF interface. Features of the external

dual-band dipole antennas are:

•Four RTNC antenna connectors on the top of the access point

•Three TX and four RX antennas

These antennas are supported on the 2602E:

Internal Antennas

The 2602I model access points are configured with up to four dual-band inverted-F antennas and two

2.4-GHz/5-GHz dual-band radios.

There are four antennas deployed inside the access point with one deployed on each corner of the

access point top housing. Each antenna covers both the 2.4 GHz and the 5 GHz bands with a single

feed line. The basic features are as follows:

•Dual-band inverted-F antenna for use in both the 2.4-GHz and 5-GHz bands.

•Antenna unit integrated into 2602I model access points.

•Peak gain is approximately 4 dBi in the 2.4-GHz band and approximately 4 dBi in the 5-GHz

band.

Regulatory Domains

The 2600 series supports the following regulatory domains (shown as “x” in the model numbers):

•-A, -C, -E, -I, -K, -N, -Q, -R, -S, -T, -Z

Countries Supported

Click this URL to browse to a list of countries and regulatory domains supported by the 2600:

www.cisco.com/go/aironet/compliance

Antenna Part Number Antenna Type Antenna Gain 2 GHz / 5 GHz

(dBi)

AIR-ANT2524DB-R Dual-resonant black dipole 2/4

AIR-ANT2524DW-R Dual-resonant white dipole 2/4

AIR-ANT2524DG-R Dual-resonant gray dipole 2/4

AIR-ANT2524V4C-R Dual-resonant, ceiling-mount omni

(4-pack)

2/4

AIR-ANT2544V4M-R Dual-resonant omni (4-pack) 4/4

AIR-ANT2566P4W-R Dual-resonant Directional antenna

(4-pack)

6/6

6 Access Point Ports and Connectors

The 2602E model access points have external antenna connectors and the LED indictor on the top of

the model, as shown in Figure 1. The 2602I model access points have integrated antennas and do not

have external connectors on the top of the unit; however, they do have the LED indicator on top of

the unit, as shown in Figure 2.

Figure 1 Access Point Ports and Connections (top)

1Antenna connector A 3Antenna connector C

2Antenna connector B 4Antenna connector D

333572

Figure 2 Access Point LED Indicator (top)

The ports and connections on the bottom of the access point are shown in Figure 3.

Figure 3 Access Point Ports and Connections (bottom)

1LED indicator

272377

2 3 4

1 5

6 6

7 Configuring the Access Point

This section describes how to connect the access point to a wireless LAN controller. Because the

configuration process takes place on the controller, see the Cisco Wireless LAN Controller

Configuration Guide for additional information. This guide is available on Cisco.com.

The Controller Discovery Process

The access point uses standard Control and Provisioning of Wireless Access Points Protocol

(CAPWAP) to communicate between the controller and other wireless access points on the network.

CAPWAP is a standard, interoperable protocol which enables an access controller to manage a

collection of wireless termination points. The discovery process using CAPWAP is identical to the

Lightweight Access Point Protocol (LWAPP) used with previous Cisco Aironet access points.

LWAPP-enabled access points are compatible with CAPWAP, and conversion to a CAPWAP controller

is seamless. Deployments can combine CAPWAP and LWAPP software on the controllers.

The functionality provided by the controller does not change except for customers who have Layer 2

deployments, which CAPWAP does not support.

In a CAPWAP environment, a wireless access point discovers a controller by using CAPWAP discovery

mechanisms and then sends it a CAPWAP join request. The controller sends the access point a

CAPWAP join response allowing the access point to join the controller. When the access point joins

the controller, the controller manages its configuration, firmware, control transactions, and data

transactions.

Note For additional information about the discovery process and CAPWAP, see the Cisco Wireless

LAN Controller Software Configuration Guide. This document is available on Cisco.com.

Note CAPWAP support is provided in controller software release 5.2 or later. However, your

controller must be running release 7.2.110.0 or later to support 2600 series access points.

1Kensington lock slot 4Console port

DC Power connection

Security padlock and hasp (padlock not

included)

3Gbit Ethernet port 6Mounting bracket pins (feet for desk or

table-top mount)

Note You cannot edit or query any access point using the controller CLI if the name of the access

point contains a space.

Note Make sure that the controller is set to the current time. If the controller is set to a time that

has already occurred, the access point might not join the controller because its certificate may

not be valid for that time.

Access points must be discovered by a controller before they can become an active part of the network.

The access point supports these controller discovery processes:

•Layer 3 CAPWAP discovery—Can occur on different subnets than the access point and uses IP

addresses and UDP packets rather than MAC addresses used by Layer 2 discovery.

•Over-the-air provisioning (OTAP)—This feature is supported by Cisco 4400 series controllers. If

this feature is enabled on the controller, all joined access points transmit wireless CAPWAP

neighbor messages, and new access points receive the controller IP address from these messages.

This feature is disabled by default and should remain disabled when all access points are installed.

Additional information about OTAP is available on Cisco.com at the following link:

http://www.ciscosystems.com/en/US/products/ps6366/products_tech_note09186a008093d74a.shtml

•Locally stored controller IP address discovery—If the access point was previously joined to a

controller, the IP addresses of the primary, secondary, and tertiary controllers are stored in the

access point’s non-volatile memory. This process of storing controller IP addresses on an access

point for later deployment is called priming the access point. For more information about priming,

see the “Performing a Pre-Installation Configuration” section on page 12.

•DHCP server discovery—This feature uses DHCP option 43 to provide controller IP addresses to

the access points. Cisco switches support a DHCP server option that is typically used for this

capability. For more information about DHCP option 43, see the “Configuring DHCP Option 43

and DHCP Option 60” section on page 35.

•DNS discovery—The access point can discover controllers through your domain name server

(DNS). For the access point to do so, you must configure your DNS to return controller IP

addresses in response to CISCO-CAPWAP-CONTROLLER.localdomain, where localdomain is

the access point domain name. Configuring the CISCO-CAPWAP-CONTROLLER provides

backwards compatibility in an existing customer deployment. When an access point receives an IP

address and DNS information from a DHCP server, it contacts the DNS to resolve

CISCO-CAPWAP-CONTROLLER.localdomain. When the DNS sends a list of controller IP

addresses, the access point sends discovery requests to the controllers.

Andere Handbücher für Aironet 2600 Series

Inhaltsverzeichnis

Andere Cisco Drahtloser Zugangspunkt Handbücher

Cisco

Cisco WAP571 Bedienungsanleitung

Cisco

Cisco AT&T U-VERSE VEN401 Bedienungsanleitung

Cisco

Cisco Linksys WAP610N Bedienungsanleitung

Cisco

Cisco WAP121 Bedienungsanleitung

Cisco

Cisco Aironet 1600 Series Kurzanleitung

Cisco

Cisco Small Business WAP551 Bedienungsanleitung

Cisco

Cisco AIR-LAP1252AG-A-K9 - Aironet 1252AG - Wireless Access... Bedienungsanleitung

Cisco

Cisco Meraki MR70 Bedienungsanleitung

Cisco

Cisco Meraki MR28 Bedienungsanleitung

Cisco

Cisco Aironet 521 Bedienungsanleitung

Cisco

Cisco Meraki Go GR62 Bedienungsanleitung

Cisco

Cisco Catalyst IW9165D Handbuch

Cisco

Cisco Catalyst 9166 Series Handbuch

Cisco

Cisco Meraki MR46 Bedienungsanleitung

Cisco

Cisco 1262 Bedienungsanleitung

Cisco

Cisco AIR-LAP1142N-A-K9 Bedienungsanleitung

Cisco

Cisco 1522AG - Aironet Lightweight Outdoor Mesh Access... Bedienungsanleitung

Cisco

Cisco Meraki MR55-HW Handbuch

Cisco

Cisco Aironet 1520 Series Bedienungsanleitung

Cisco

Cisco Linksys WAP610N Bedienungsanleitung

Cisco

Cisco Meraki MR36 Bedienungsanleitung

Cisco

Cisco 7330 Bedienungsanleitung

Cisco

Cisco Aironet 1830 Series Bedienungsanleitung

Cisco

Cisco 700 series Bedienungsanleitung

Beliebte Drahtloser Zugangspunkt Handbücher anderer Marken

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Bedienungsanleitung

Ubiquiti

Ubiquiti NanoStation NSM2 Bedienungsanleitung

Aruba

Aruba IAP-335 Bedienungsanleitung

Advantek Networks

Advantek Networks AWN-AP-54MR Bedienungsanleitung

IP-COM

IP-COM AP355 Bedienungsanleitung

Buffalo

Buffalo AirStation WLA-L11G Bedienungsanleitung

EnGenius

EnGenius EnStationACv2 Bedienungsanleitung

D-Link

D-Link DAP-3662 Bedienungsanleitung

xG Technology

xG Technology xMax CN1300 Bedienungsanleitung

Widelink

Widelink ezWave WAP-1100 Series Bedienungsanleitung

Edimax

Edimax CAP1200 Bedienungsanleitung

Ubiquiti

Ubiquiti LBE-5AC-Gen2 Bedienungsanleitung

Aruba

Aruba AP-203R Bedienungsanleitung

LuXout Shades

LuXout Shades LUXSHADE MOTION Bedienungsanleitung

CreatComm

CreatComm TB5F Bedienungsanleitung

SineDigital

SineDigital MW-1500AP(H) Bedienungsanleitung

TP-Link

TP-Link AP9650 V1 Bedienungsanleitung

Draytek

Draytek VIGORAP 902 Bedienungsanleitung