Cisco Meraki CW9163E Bedienungsanleitung
CW9163E Installation Guide
About this Guide
This guide provides instructions on installing and configuring your CW9163E access point. This guide also provides mounting instructions and limited
troubleshooting procedures. For more wireless installation guides, refer to our documentation website's wireless installation guides section.
Product Overview
The Cisco Wireless CW9163E is an outdoor-rated, enterprise-class 802.11ax cloud-managed access point. The AP is equipped with tri-band concurrent radios
geared towards low/medium density applications. It will work with different external antennas for required directivity.
It features 2x2 tri-band traffic radios (2x2 2.4 G z + 2x2 5 G z + 2x2 6 G z), 1x1 tri-band scanning radio, and a 2.4 G z IoT radio for (BLE/Zigbee/Thread etc).
It also has an inbuilt GNSS receiver for 6 G z AFC compliance.
Physical Specifications
Dimensions and Weight
Interfaces
• 1x 10/100/1000/2.5G BASE-T Ethernet (RJ45)
• Four external N-type female antenna connectors
Antennas
• CW-ANT-O1-NS-00 (Direct Attach Omni Directional Antenna, tri-band)
• CW-ANT-D1-NS-00 (tri-band Patch, two 2.4 / 5 G z dual-band ports and Two 5 / 6 G z ports (Total 4 antenna ports)
• CW-ANT-GPS2-00 (L1/L5 Dual Band R CP GNSS antenna (active))
Power
• 802.3at PoE
• 802.3af (degraded performance mode)
• Injectors Supported:
◦ AIR-PWRINJ6 [30 W rated single-port PoE injector]
◦ AIR-PWRINJ7 [65 W rated single-port PoE injector (802.3bt), mGig Ethernet]
1
◦ MA-INJ-4 [30 W rated single-port PoE injector]
◦ MA-INJ-6 [60 W rated PoE injector (802.3bt), mGig Ethernet]
◦ AIR-PWRINJ-60RGDMG [37 W rated power injector]
Note: Actual power consumption may vary depending on the AP usage.
Note: The power injector provides DC voltage to the AP over the Ethernet cable and supports a total end-to-end Ethernet cable length of 100 m (328
ft) from the switch to the AP
Environment
• IP67 Environmental rating
• Up to 100/165 mph wind (sustained/gust)
• Operating temperature:
◦ -40° to +65° C
Security
• Four security screws
• Two mounting straps
• Supports secure boot
Package Contents
The CW9163E package contains the following:
•Quick install guide
•Regulatory compliance and safety information
•CW9163E Cloud-Managed Access Point
•Mount Plate, MA-MNT-MR-16
•Support bracket
•Grounding cable
•Gift Box
◦Mounting straps
◦Ground lug
◦RJ-45 Field termination gland
◦Waterproof cap
◦Antenna tape
2
◦Oxide inhibitor paste (Find purpose)
Product View and Physical Features
Your CW9163E has the following physical features:
3
The mount cradle has the following physical features:
A, C, E, G- Antenna port
B- Grounding post
D- GPS Antenna port
F- Mounting slots
- Ethernet/ Console ports
I- Positive reset cap (Covers access to rest button)
J- LED indicator
LED Indicator
The CW9163E is equipped with a multi-color LED on the bottom edge of the unit to convey information about system functionality and performance:
•Orange - AP is booting (permanent Orange suggests hardware issue)
•Rainbow - AP is initializing/scanning
•Blinking Blue - AP is upgrading
•Green - AP in Gateway mode with no clients
•Blue - AP in Gateway mode with clients
•Blinking Orange - AP can't find uplink
The CW9163E may be operated in “Run Dark” mode for additional security and to reduce the visibility of the access point. In this mode, the LED will not be
illuminated. This mode may be enabled through the Meraki Dashboard.
Ethernet Port
The CW9163E features one PoE 2.5 Gbps Ethernet port which can be sealed with a cable gland for outdoor operation.
The ethernet port accepts 802.3at power and should be used as the primary uplink to your LAN/WAN.
4
Powering Options:
Power
mode
PoE
Class Eth0 2.4GHz 5GHz 6GHz
max RF
power
ch0/ch1
Scan BLE GNSS (tracking)
1 AF 1 Gbps 1x1 1x1
off
22 dBm off off on
2 AT 2.5 Gbps 2x2 2x2 2x2 21 dBm on on on
Mount plate attachment slots
The mounting slots located on the rear shell of the CW9163E marry to the 4 mounting posts on the mounting plate, securely fastening the CW9163E to the
mounting plate.
Grounding post
The grounding post is located on the left side of the CW9163E unit. Using the included grounding lug, ground the unit to mitigate lightning and other adverse
electrical events.
Factory reset button
Using a flathead screwdriver, remove the reset cap to access the reset pinhole. If the pinhole push button is pressed and held for at least five seconds and then
released, the CW9163E will reboot and be restored to its original factory settings by deleting all configuration information stored on the unit.
Understanding the CW9163E mount plate
The MA-MNT-MR-16 mount plate will ship with the installation kit.
MA-MNT-MR-16
Note: The CW9163E will operate utilizing 802.3af in degraded mode. Please reference the power table below for the expected performance.
5
A- Wall mount slots
B- Vertical pole strap slots
C- Mount plate security screw
D- Mount plate attachment posts
E- orizontal pole strap slots
F- Release tab
AIR-MNT-VERT1
Note: The CW9163E is compatible with the AIR-MNT-VERT1 mounting plate. Refer to the below diagrams on mounting plate specifications.
6
A- Wall mount slots
B- Mount plate attachment screw
C- Release tab
D- Mounting posts
Mounting holes A (4x)
The mounting holes located on the 4 outermost corners of the MA-MNT-MR-16 mounting plate allow secure installation of the mounting plate to a surface such
as a wall.
Vertical orientation mounting strap slots B (2x)
The vertical orientation mounting strap slots located in the middle of the mounting plate secure the mounting plate to a vertical pole using the included mounting
straps.
Mount plate attachment screw C
The mount plate attachment screw is located at the bottom of the MA-MNT-MR-16 mounting plate. It securely attaches the AP to the mounting plate.
7
Mounting posts D (4x)
The mounting posts are located in the middle of the MA-MNT-MR-16 mounting plate, secure the CW9163E to the mounting plate via mounting slots on the AP.
Horizontal orientation mounting strap slots E (2x)
The horizontal orientation mounting strap slots located in the middle of the MA-MNT-MR-16 mounting plate secure the mounting plate to a horizontal pole using
the included mounting straps.
Release tab F
The release tab is located at the bottom of the MA-MNT-MR-16 mounting plate. Press down the release tab to when detaching the AP to unlock.
Safety and Warnings
These operations are to be taken with respect to all local laws. Please consider the following for safe operation:
•Power off the unit before you begin. Read the installation instructions before connecting the system to the power source.
•Before you work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar with standard practices for preventing
accidents.
•Read the wall-mounting instructions carefully before beginning installation. Failure to use the correct hardware or to follow the correct procedures could
result in a hazardous situation to people and damage to the system.
•This product relies on the building’s installation for short-circuit (overcurrent) protection. Ensure that the protective device is rated not greater than 15 A,
125 Vac, or 10A, 240 Vac.
•Please only power the device with the provided power cables or standard PoE to ensure regulatory compliance.
Pre-Install Preparation
You should complete the following steps before going on-site to perform an installation.
Configure Your Network in Dashboard
The following is a brief overview of the steps required to add a CW9163E to your network. For detailed instructions about creating, configuring, and managing
wireless networks, refer to the online documentation (documentation.meraki.com/mr).
1. Login to http://dashboard.meraki.com. If this is your first time, create a new account.
2. Find the network to which you plan to add your APs or create a new network.
3. Add your APs to your network. You will need your Cisco Wireless order number (found on your invoice) or the serial number of each AP, which looks like
Qxxx-xxxx-xxxx, and is found on the bottom of the unit. You will also need your Enterprise license key, which you should have received via email.
4. Go to the map / floor plan view and place each AP on the map by clicking and dragging it to the location where you plan to mount it.
Check and Upgrade Firmware
To ensure your CW9163E performs optimally immediately following installation, it is recommended that you facilitate a firmware upgrade prior to mounting your
CW9163E.
8
1. Attach your CW9163E to PoE-enabled wired Internet connection. See the "Power the CW9163E" section for details.
2. The CW9163E will turn on, and the LED will glow solid orange. If the unit does not require a firmware upgrade, the LED will turn either green (no clients
associated) or blue (clients associated) within thirty seconds.
* If the unit requires an upgrade, the LED will begin blinking blue until the upgrade is complete, at which point the LED will turn solid green or blue. You should
allow at least a few minutes for the firmware upgrade to complete, depending on the speed of your internet connection.
Check and Configure Firewall Settings
If a firewall is in place, it must allow outgoing connections on particular ports to particular IP addresses. The most current list of outbound ports and IP addresses
for your particular organization can be found here.
Assigning IP Addresses to CW9163E
All gateway CW9163E (CW9163E with Ethernet connections to the LAN) must be assigned routable IP addresses. These IP addresses can be dynamically
assigned via D CP or statically assigned.
Dynamic Assignment (Recommended)
When using D CP, the D CP server should be configured to assign a static IP address for each MAC address belonging to an AP. Other wireless network
features, such as 802.1X authentication, may rely on the property that the APs have static IP addresses.
Static Assignment
Static IPs are assigned using the local web server on each AP. The following procedure describes how to set the static IP:
1. Using a client machine (e.g., a laptop), connect to the AP wirelessly (by associating to any SSID broadcast by the AP) or over a wired connection.
2. If using a wired connection, connect the client machine to the CW9163E either through a PoE switch or a PoE Injector. If using a PoE switch, plug an
Ethernet cable into the CW9163E’s Ethernet jack and the other end into a PoE switch. Then connect the client machine over the Ethernet cable to the
PoE switch. If using a PoE Injector, connect the CW9163E to the “PoE” port of the Injector and the client machine to the “LAN” port.
3. Using a web browser on the client machine, access the AP’s built-in web server by browsing to http://my.meraki.com. Alternatively, browse to
http://10.128.128.128.
4. Click on the “Uplink Configuration” tab. Log in. The default login is the serial number (e.g. Qxxx-xxxx-xxxx), with no password (e.g., Q2DD-551C-ZYW3).
5. Configure the static IP address, netmask, gateway IP address, and DNS servers that this AP will use on its wired connection.
6. If necessary, reconnect the AP to the LAN.
Static IP via DHCP Reservations
Instead of associating each CW AP individually to configure static IP addresses, an administrator can assign static IP addresses on the upstream D CP server.
Through “D CP reservations,” IP addresses are “reserved” for the MAC addresses of the CW APs. Please consult the documentation for the D CP server to
configure D CP reservations.
Collect Tools
You will need the following tools to efficiently install the CW9163E.
9
Required Hardware for Installation
You will need the following tools to perform an installation:
•Network cables with RJ45 connectors long enough for your particular mounting location
•802.3at PoE power source (either PoE switch or PoE Injector)
•Connection to the Internet (if you are setting up your CW9163E as a gateway to the Internet)
•Appropriately sized metal straps (if mounting to a pole larger than 3.9” in diameter)
•Screws- should be up to 6 mm in diameter and at least 1 - 1/4 inch length
•Mounting anchors appropriate for installation surface
Installation Instructions
For most mounting scenarios, the MA-MNT-MR-16 provides a quick, simple, and flexible means of mounting the CW9163E. The installation should be done in
two steps. First, install the mount plate to your selected location. Then, attach the CW9163E to the mount plate.
Warning: Due to the heat dissipation in the back of APs during normal operation, please do not stack powered-on APs on top of each other during
pre-installation to avoid heat damage.
10
Inhaltsverzeichnis
Andere Cisco Drahtloser Zugangspunkt Handbücher
Cisco
Cisco 1004-CH - 1004 Enet/ISDN/Bri Rter Kurzanleitung
Cisco
Cisco AIR-AP1121G-E-K9 Handbuch
Cisco
Cisco WAP121 Bedienungsanleitung
Cisco
Cisco Catalyst 9130AX Series Bedienungsanleitung
Cisco
Cisco Small Business AP541N Bedienungsanleitung
Cisco
Cisco Catalyst 9136I Series Bedienungsanleitung
Cisco
Cisco MERAKI MR34 Bedienungsanleitung
Cisco
Cisco Meraki MR70 Bedienungsanleitung
Cisco
Cisco WAP200 - Small Business Wireless-G Access... Bedienungsanleitung
Cisco
Cisco AIR-LAP1242AG-A-K9 Bedienungsanleitung
Cisco
Cisco Aironet 600 Series Bedienungsanleitung
Cisco
Cisco WAP121 Bedienungsanleitung
Cisco
Cisco AIR-AP1232AG-A-K9 - Aironet 1230AG - Wireless Access... Bedienungsanleitung
Cisco
Cisco Aironet 1700 Kurzanleitung
Cisco
Cisco Aironet 1200 Series Bedienungsanleitung
Cisco
Cisco Meraki MR55 Bedienungsanleitung
Cisco
Cisco 1130AG - Aironet - Wireless Access Point Handbuch
Cisco
Cisco Aironet OfficeExtend AIR-OEAP602I-E-K9 Bedienungsanleitung
Cisco
Cisco AT&T U-VERSE VEN401 Bedienungsanleitung
Cisco
Cisco 1830 Series Bedienungsanleitung
Beliebte Drahtloser Zugangspunkt Handbücher anderer Marken
D-Link
D-Link DWL-2100AP - AirPlus Xtreme G Bedienungsanleitung
Ubiquiti
Ubiquiti NanoStation NSM2 Bedienungsanleitung
Aruba
Aruba IAP-335 Bedienungsanleitung
Advantek Networks
Advantek Networks AWN-AP-54MR Bedienungsanleitung
IP-COM
IP-COM AP355 Bedienungsanleitung
Buffalo
Buffalo AirStation WLA-L11G Bedienungsanleitung
