Cisco Meraki MR12 Bedienungsanleitung

Assigning Static IP Addresses to an MR12 or MR58

The MR12 and MR58 wireless access points have two Ethernet ports that can be used to connect the device to a wired network. However, a static IP can only

be set on the primary Ethernet interface.

This article will discuss:

• Identifying the primary Ethernet port

• Behavior differences between primary and secondary ports

• Determining which port is being used

•Assigning a static IP

Identifying the Primary Ethernet Port

MR12

The primary Ethernet port is directly adjacent to the power connector and is labeled as Uplink.

MR58

The primary Ethernet port is located on the bottom-left side of the AP and is labeled as ETH0.

Behavior differences between primary and secondary ports

Primary (Ethernet 0)

This interface is capable of receiving power using PoE and can be assigned a static IP address. It is also capable of 10/100/1000Mbps speeds. It is intended for

connecting the MR12 to the rest of the network.

Secondary (Ethernet 1)

This interface can only receive an IP from DHCP and is not able to receive power using PoE. It is only capable of 10/100 speeds. It is still able to connect to the

Meraki Cloud Controller if the Primary connection is down, but is intended for used by a wired client. To allow use by a wired client, please refer to our

documentation regarding Extending the LAN with a Wireless Mesh Link.

Determining which port is being used

The simplest way to determine which port is being used is to physically look at the device, and refer to the diagrams above. If you are not near the device, the

easiest way to determine if the secondary port is being used is by looking at the AP Dashboard. Navigate to Monitor > Access points and click the AP in

question. Look under Status for LAN IP #. If the # = 1, then the AP is connected using the primary port. If # = 2, then the AP is connected using its secondary

port.

Assigning a static IP

A static IP can be assigned to the AP's primary interface in two ways.

Dashboard

1. In Dashboard, go to Monitor > Access points and select the AP in question.

2. Click the Edit icon.

3. On the page that appears, next to IP type select Static IP.

4. Enter the appropriate settings and click Save.

Local web interface

Refer to the MR Quick Start Guide for instructions on how to set the IP address using the local web interface.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Cisco Drahtloser Zugangspunkt Handbücher

Cisco

Cisco Linksys WAP54GX Bedienungsanleitung

Cisco

Cisco Meraki CW9163E Bedienungsanleitung

Cisco

Cisco AIR-AP1131G-A-K9 Bedienungsanleitung

Cisco

Cisco Meraki MR20-HW Bedienungsanleitung

Cisco

Cisco AIR-LAP1252AG-A-K9 - Aironet 1252AG - Wireless Access... Bedienungsanleitung

Cisco

Cisco MERAKI MR66 Bedienungsanleitung

Cisco

Cisco Aironet Wave 2 Installationshandbuch

Cisco

Cisco 1262 Bedienungsanleitung

Cisco

Cisco AIR-AP1832I K9C Series Bedienungsanleitung

Cisco

Cisco Meraki MR56 Bedienungsanleitung

Cisco

Cisco 1130AG - Aironet - Wireless Access Point Bedienungsanleitung

Cisco

Cisco Aironet 1300 Series Handbuch

Cisco

Cisco Aironet 1570 Series Bedienungsanleitung

Cisco

Cisco Meraki MR42E Bedienungsanleitung

Cisco

Cisco WET200 Wireless-G Business Ethernet Bridge Bedienungsanleitung

Cisco

Cisco Aironet 1200 Series Bedienungsanleitung

Cisco

Cisco AIR-CAP3502I-A-K9 Bedienungsanleitung

Cisco

Cisco AIR-LAP1242AG-A-K9 Bedienungsanleitung

Cisco

Cisco Catalyst 9166 Series Handbuch

Cisco

Cisco Wap581 Bedienungsanleitung

Cisco

Cisco Meraki Go GR10 Bedienungsanleitung

Cisco

Cisco AIR-AP1120B-A-K9 - Aironet 1100 Series Access... Handbuch

Cisco

Cisco IW3702 Bedienungsanleitung

Cisco

Cisco MERAKI MR72 Bedienungsanleitung

Beliebte Drahtloser Zugangspunkt Handbücher anderer Marken

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Bedienungsanleitung

Ubiquiti

Ubiquiti NanoStation NSM2 Bedienungsanleitung

Aruba

Aruba IAP-335 Bedienungsanleitung

Advantek Networks

Advantek Networks AWN-AP-54MR Bedienungsanleitung

IP-COM

IP-COM AP355 Bedienungsanleitung

Buffalo

Buffalo AirStation WLA-L11G Bedienungsanleitung

EnGenius

EnGenius EnStationACv2 Bedienungsanleitung

D-Link

D-Link DAP-3662 Bedienungsanleitung

xG Technology

xG Technology xMax CN1300 Bedienungsanleitung

Widelink

Widelink ezWave WAP-1100 Series Bedienungsanleitung

Edimax

Edimax CAP1200 Bedienungsanleitung

Ubiquiti

Ubiquiti LBE-5AC-Gen2 Bedienungsanleitung

Aruba

Aruba AP-203R Bedienungsanleitung

LuXout Shades

LuXout Shades LUXSHADE MOTION Bedienungsanleitung

CreatComm

CreatComm TB5F Bedienungsanleitung

SineDigital

SineDigital MW-1500AP(H) Bedienungsanleitung

TP-Link

TP-Link AP9650 V1 Bedienungsanleitung

Draytek

Draytek VIGORAP 902 Bedienungsanleitung