Cisco MERAKI MR46E-HW Handbuch

Meraki MR46E-HW

Hardware Installation Guide

Trademarks

Meraki, Meraki MR46E-HW, Meraki Cloud Controller, and Meraki Mesh are trademarks of Cisco Systems, Inc.

Other brand and product names are registered trademarks or trademarks of their respective holders.

Statement of Conditions

In the interest of improving internal design, operational function, and/or reliability, Cisco Systems reserves the

right to make changes to the products described in this document without notice. Cisco Systems does not

assume any liability that may

occur due to the use or application of the product(s) or circuit layout(s)

described herein.

Warranty

Meraki, Inc. provides a lifetime warranty on this product. Warranty details may be found at

www.meraki.com/legal.

Table of Contents

Scope of Document and Related Publications 4

MR46E-HW Overview 5

2.1

Package Contents 5

2.2

Understanding the MR46E-HW 5

2.3

Security Features 7

2.4

Ethernet Ports 7

2.5

Power Source Options 7

2.6

Factory Reset Button 7

2.7

LED Indicators and Run Dark Mode 7

Pre-Install Preparation 8

3.1

Configure Your Network in Dashboard 8

3.2

Check and Upgrade Firmware 8

3.3

Check and Configure Firewall Settings 8

3.4

Assigning IP Addresses to MR46E-HWs 9

3.4.1

Dynamic Assignment 9

3.4.2

Static

Assignment 9

3.4.3

Static IP

Assignment via DHCP Reservations 9

3.5

Collect Tools 10

3.6

Collect Additional Hardware for Installation 10

Installation Instructions 11

4.1

Choose Your Mounting Location 11

4.2

Install the MR46E-HW 11

4.2.1

Attach the Mount Plate 11

4.2.1.1

Wall or Solid

Ceiling Mount Using Mount Plate 13

4.2.1.2

Drop Ceiling

Mount Using Mount Plate 14

4.2.1.3

Electrical Junction Box Mount Using Mount Plate 18

4.2.2

Power the MR46E-HW 20

4.2.2.1

Powering the MR46E-HW with Meraki AC Adapter 21

4.2.2.2

Powering the MR46E-HW with Meraki 802.3at Power over Ethernet Injector 21

4.2.2.3

Powering the MR46E-HW with an 802.3at Power over Ethernet Switch 22

4.2.3

Mount the MR46E-HW 22

4.2.3.1

Assemble Security Hasp to the MR46E-HW 22

4.2.3.2

Assemble MR46E-HW to the Mount Plate 23

4.2.3.3

Desk or Shelf Mount 25

4.3

Secure the MR46E-HW 26

4.3.1

Security Screw 26

4.3.2

Kensington Lock 26

4.4

Verify Device Functionality and Test Network Coverage 27

Troubleshooting 27

Scope of Document and Related Publications

The MR46E-HW Hardware Installation Guide describes the installation procedure for the MR46E-HW

indoor access point. Additional reference documents are available online at

www.meraki.com/library/product.

MR46E-HW Overview

The Meraki MR46E-HW is an enterprise-class, dual-concurrent 4x4 MIMO 802.11ax indoor access

point designed for

high-density deployments in offices, schools, hospitals and hotels. When connected

to the Meraki Cloud Controller, the MR46E-HW enables the creation of ultra-high speed, reliable indoor

wireless networks quickly, easily and cost-

effectively.

2.1

Package Contents

The MR46E-HW package contains the following:

•MR46E-HW access point

•Mounting plate

•Drop ceiling mounting kit wall screws

•Security screws

•Mounting Template

2.2

UnderstandingtheMR46E-HW

MR46E-HW Operation Temperature:

32 ° F to 104 ° F (0 ° C to 40 ° C)

Your Meraki MR46E-HW has the following features:

Kensington lock hard point

Mount plate attachment slots (2x)

Cable access bay

Desk mount feets (4x)

MR46E-HW cable access bay

Factory Reset Button

Ethernet port Power supplied by PoE: 50-57Vdc 0.6A

AC Adapter plug (sold separately) Power supplied by adapter: 12Vdc, 2.5A

Your MR46E-HW mount plate has the following features:

Access point mounting posts (2x)

Various mounting holes

2.3

Security Features

The MR46E-HW features multiple options for physically securing the access point after installation:

Security screw –The accessory kit includes screws that can be used to secure the access point to

the mount plate. Engaging the security screw prevents accidental dislodging and theft.

Kensington lock –The access point contains a hard point that allows it to be secured to any nearby

permanent structure using a standard Kensington lock.

2.4

Ethernet Ports

The MR46E-HW features an Ethernet RJ45 port that accepts 802.3at power (labeled “PoE”). This port

should

be used for uplink to your WAN connection.

2.5

Power Source Options

The MR46E-HW access point can be powered using either the Meraki AC Adapter or 802.3at PoE Injector

(both sold

separately) or a third-party 802.3at PoE switch.

2.6

Factory Reset Button

If the button is pressed and held for at least five seconds and then released, the MR46E-HW will reboot

and be

restored to its original factory settings by deleting all configuration information stored on the unit.

Pre-Install Preparation

You should complete the following steps before going on-site to perform an installation.

3.1

Configure Your Network in Dashboard

The following is a brief overview only of the steps required to add an MR46E-HW to your network. For

detailed instructions about creating, configuring and managing Meraki wireless networks, refer to the

Meraki Cloud Controller Manual (meraki.com/library/product).

Find the network to which you plan to add your APs or create a new network.

Add your APs to your network. You will need your Meraki order number (found on your invoice if you

ordered directly from Meraki) or the serial number of each AP, which looks like Qxxx-xxxx-xxxx, and is

found on the bottom of the unit. You will also need your Enterprise Cloud Controller license key, which

you should have received via email from shippi[email protected].

Go to the map / floor plan view and place each AP on the map by clicking and dragging it to the

location where you plan to mount it.

3.2

Check and Upgrade Firmware

To ensure your MR46E-HW performs optimally immediately following installation, Meraki recommends

that you facilitate a firmware upgrade prior to mounting your MR46E-HW.

Attach your MR46E-HW to power and a wired Internet connection. See p. 19 of this Hardware

Installation

Guide for details.

The MR46E-HW will turn on and the Power LED will glow solid orange. If the unit does not require a

firmware

upgrade, the Power LED will turn white within thirty seconds.

* If the unit requires an upgrade, the Power LED will begin blinking orange until the upgrade is

complete,

at which point the Power LED will turn solid white. You should allow about an hour for the

firmware

upgrade to complete, depending on the speed of your internet connection.

3.3

Check and Configure Firewall Settings

If a firewall is in place, it must allow outgoing connections on particular ports to particular IP addresses.

The most current list of outbound ports and IP addresses can be found here:

http://tinyurl.com/y79une3

3.4

Assigning IP Addresses to MR46E-HWs

All gateway MR46E-HWs (MR46E-HWs with Ethernet connections to the LAN) must be assigned routable IP

addresses.

These IP addresses can be dynamically assigned via DHCP or statically assigned.

3.4.1

Dynamic Assignment

When using DHCP, the DHCP server should be configured to assign a static IP address for each MAC address

belonging to a Meraki AP. Other features of the wireless network such as 802.1x authentication, may rely on

the

property that the APs have static IP addresses.

3.4.2

Static Assignment

Static IPs are assigned using the local web server oneach AP. The following procedure describes how to set

the static IP:

Using a client machine (e.g. a laptop), connect to the AP either wirelessly (by associating to any SSID

broadcast by the AP) or over a wired connection.

If using a wired connection, connect the client machine to the MR46E-HW either through a PoE switch or a

Meraki

PoE Injector. If using a PoE switch, plug an Ethernet cable into the MR46E-HW’s Ethernet jack, and the

other end

into a PoE switch. Then connect the client machine over Ethernet cable to the PoE switch. If using a

Meraki

PoE Injector, connect the MR46E-HW to the “PoE” port of the Injector, and the client machine to the

“LAN” port.

Using a web browser on the client machine, access the AP’s built-in web server by browsing to

http://my.meraki.com. Alternatively, browse to http://10.128.128.128.

Click on the “Static IP Configuration” tab. Log in. The default user name is “admin”. The default password

is the AP’s serial number, with hyphens included

Configure the static IP address, net mask, gateway IP address and DNS servers that this AP will use on its

wired connection.

If necessary, reconnect the AP to the LAN.

3.4.3

Static IP via DHCP Reservations

Instead of associating to each Meraki AP individually to configure static IP addresses, an administrator can

assign

static IP addresses on the upstream DHCP server. Through “DHCP reservations”, IP addresses are

“reserved” for the

MAC addresses of the Meraki APs. Please consult the documentation for the DHCP server

to configure DHCP

reservations.

Inhaltsverzeichnis

Andere Cisco Drahtloser Zugangspunkt Handbücher

Cisco

Cisco Aironet 1550 Series Bedienungsanleitung

Cisco

Cisco Aironet 350 Series Handbuch

Cisco

Cisco Meraki CW9162I-MR Handbuch

Cisco

Cisco Catalyst IW6300 Series Handbuch

Cisco

Cisco Aironet 1240AG Series Handbuch

Cisco

Cisco Meraki Go GR12 Bedienungsanleitung

Cisco

Cisco Meraki MR20-HW Bedienungsanleitung

Cisco

Cisco ASA 5508-X Handbuch

Cisco

Cisco WAP125 Bedienungsanleitung

Cisco

Cisco WAP121 Bedienungsanleitung

Cisco

Cisco 1700 series Handbuch

Cisco

Cisco Aironet 1850 Series Bedienungsanleitung

Cisco

Cisco Aironet 1600 Series Kurzanleitung

Cisco

Cisco WAP4410N - Small Business Wireless-N Access... Bedienungsanleitung

Cisco

Cisco 7330 Bedienungsanleitung

Cisco

Cisco 1142 - Aironet Standalone AP Bedienungsanleitung

Cisco

Cisco Digistar EoC Bedienungsanleitung

Cisco

Cisco Cisco Aironet Wireless LAN Client Bedienungsanleitung

Cisco

Cisco Aironet 1815T Bedienungsanleitung

Cisco

Cisco Aironet 3502P Bedienungsanleitung

Cisco

Cisco Aironet 1570 Series Bedienungsanleitung

Cisco

Cisco MR18 Bedienungsanleitung

Cisco

Cisco Aironet 1520 Series Handbuch

Cisco

Cisco AIR-AP1010 - 1000 Series Lightweight Access... Bedienungsanleitung

Beliebte Drahtloser Zugangspunkt Handbücher anderer Marken

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Bedienungsanleitung

Ubiquiti

Ubiquiti NanoStation NSM2 Bedienungsanleitung

Aruba

Aruba IAP-335 Bedienungsanleitung

Advantek Networks

Advantek Networks AWN-AP-54MR Bedienungsanleitung

IP-COM

IP-COM AP355 Bedienungsanleitung

Buffalo

Buffalo AirStation WLA-L11G Bedienungsanleitung

EnGenius

EnGenius EnStationACv2 Bedienungsanleitung

D-Link

D-Link DAP-3662 Bedienungsanleitung

xG Technology

xG Technology xMax CN1300 Bedienungsanleitung

Widelink

Widelink ezWave WAP-1100 Series Bedienungsanleitung

Edimax

Edimax CAP1200 Bedienungsanleitung

Ubiquiti

Ubiquiti LBE-5AC-Gen2 Bedienungsanleitung

Aruba

Aruba AP-203R Bedienungsanleitung

LuXout Shades

LuXout Shades LUXSHADE MOTION Bedienungsanleitung

CreatComm

CreatComm TB5F Bedienungsanleitung

SineDigital

SineDigital MW-1500AP(H) Bedienungsanleitung

TP-Link

TP-Link AP9650 V1 Bedienungsanleitung

Draytek

Draytek VIGORAP 902 Bedienungsanleitung