Cisco Meraki MR76 Bedienungsanleitung
MR76 Installation Guide
The Cisco Meraki MR76 are dual-band enterprise class 802.11ax cloud-managed access points. Designed for highest capacity and highest density, the
MR76 meets the needs of the most demanding environments. The access point also includes a third radio dedicated to optimizing the RF environment
and securing the airwaves.
About this Guide
This guide provides instruction on how to install and configure your MR76 access points. This guide also provides mounting instructions and limited
troubleshooting procedures. For more wireless installation guides, refer to the wireless installation guides section on our documentation website.
Product Overview
Physical Specifications
MR76
Interfaces
• 1x 10/100/1000 BASE-T Ethernet (RJ45)
• Four external N-type female antenna connectors
Power
• Power over Ethernet: 37 - 57 V (802.3af compatible)
• Power consumption: 15W max (802.3af)
• Power over Ethernet injector sold separately
Environment
• Operating temperature: -40 °F to 131 °F (-40 °C to 55 °C)
• Humidity: 5 to 95% non-condensing
• IP67 Environmental rating
Physical Security
Note: Actual power consumption may vary depending on the AP usage.
1
• Two security screws
Package Contents
The MR76 package contains the following:
• MR76 Cloud-Managed Access Point
• Mount cradle
• Wall screws
• Wall screw anchors
• rounding screws
• Mounting straps
Product View and Physical Features
Your Meraki MR76 has the following physical features:
2
The mount cradle has the following physical features:
3
4
LED indicator
Your MR76 is equipped with a multi-color LED light on the bottom edge of the unit to convey information about system functionality and performance:
• Orange - AP is booting (permanent Orange suggests hardware issue)
• Rainbow - AP is initializing/scanning
• Blinking Blue - AP is upgrading
• reen - AP in ateway mode with no clients
• Blue - AP in ateway mode with clients
• Blinking Orange - AP can't find uplink
The MR76 may be operated in “Run Dark” mode for additional security and to reduce the visibility of the access point. In this mode, the LED will not be
illuminated. This mode may be enabled through the Meraki dashboard.
Ethernet Port
The MR76 features one Ethernet ports:
This accepts 802.3af power and should be used as the primary uplink to your LAN/WAN.
N- ype antenna attachment ports (4x)
2x N-Type antenna ports are located at the top of the MR76 and 2x are located at the bottom of the MR76. The 4 antenna ports are connected to 2.4 Hz and
5 Hz client serving radios respectively. Please see the markings on the AP to verify 2.4 Hz and 5 Hz ports. In order to ensure the highest performance,
ensure antennas connected to the 4 ports have overlapping coverage areas.
Mount plate attachment slots
The mounting slots located on the rear shell of the MR76 marry to the 4 mounting posts on the mounting plate, securely fastening the MR76 to the mounting
plate.
Factory reset button
The factory reset button is located in a small pin-sized hole just above the PoE Ethernet port of the MR76. If the button is pressed and held for at least five
seconds and then released, the MR76 will reboot and be restored to its original factory settings by deleting all configuration information stored on the unit.
he Vent
The vent allows pressure equalization between the interior and the environment. This prevents internal condensation and maintains a waterproof seal.
5
Understanding the MR76 mount plate
The mount cradle has the following features:
Mounting posts (4x)
The mounting slots located in the middle of the mounting plate marry the MR76 to the mounting plate.
Mounting holes (4x)
The mounting holes located on the 4 outermost corners of the mounting plate allow secure installation of the mounting plate to a surface such as a wall.
Vertical orientation mounting strap slots (2x)
The vertical orientation mounting strap slots located in the middle of the mounting plate secure the mounting plate to a vertical pole using the included mounting
straps.
Horizontal orientation mounting strap slots (2x)
The horizontal orientation mounting strap slots located in the middle of the mounting plate secure the mounting plate to a horizontal pole using the included
mounting straps.
Release tab
The release tab located at the bottom of the mounting plate. It locks the movement of the AP once attached.
Mount plate attachment screw
The mount plate attachment screw is located at the bottom of the mounting plate. It securely attaches the AP to the mounting plate.
Mount plate grounding post
The mount plate grounding post located on the left side of the mounting plate. Using the included grounding strap, the ground post allows you to ground the
unit.
Safety and Warnings
These operations are to be taken with respect to all local laws. Please take the following into consideration for safe operation:
• Power off the unit before you begin. Read the installation instructions before connecting the system to the power
source.
• Before you work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar with
standard practices for preventing accidents.
• Read the wall-mounting instructions carefully before beginning installation. Failure to use the correct hardware or to
follow the correct procedures could result in a hazardous situation to people and damage to the system.
• This product relies on the building’s installation for short-circuit (overcurrent) protection. Ensure that the protective
The mount plate is unique to the MR76. Previous outdoor AP mount plates are not compatible with the MR76.
6
device is rated not greater than: 15 A, 125 Vac, or 10A, 240 Vac.
• Please only power the device with the provided power cables or standard PoE to ensure regulatory compliance.
Pre-Install Preparation
You should complete the following steps before going on-site to perform an installation.
Configure Your Network in Dashboard
The following is a brief overview only of the steps required to add an MR76 to your network. For detailed instructions about creating, configuring and managing
Meraki wireless networks, refer to the online documentation (documentation.meraki.com/mr).
1. Login to http://dashboard.meraki.com. If this is your first time, create a new account.
2. Find the network to which you plan to add your APs or create a new network.
3. Add your APs to your network. You will need your Meraki order number (found on your invoice) or the serial
number of each AP, which looks like Qxxx-xxxx-xxxx, and is found on the bottom of the unit. You will also need
your Enterprise license key, which you should have received via email.
4. o to the map / floor plan view and place each AP on the map by clicking and dragging it to the location where you
plan to mount it.
Check and Upgrade Firmware
To ensure your MR76 performs optimally immediately following installation, it is recommended that you facilitate a firmware upgrade prior to mounting your
MR76.
1. Attach your MR76 to PoE enabled wired Internet connection. See the "Power the MR76" section for details.
2. The MR76 will turn on and the LED will glow solid orange. If the unit does not require a firmware upgrade, the LED
will turn either green (no clients associated) or blue (clients associated) within thirty seconds.
* If the unit requires an upgrade, the LED will begin blinking blue until the upgrade is complete, at which point the LED will turn solid green or blue. You should
allow at least a few minutes for the firmware upgrade to complete, depending on the speed of your internet connection.
Check and Configure Firewall Settings
If a firewall is in place, it must allow outgoing connections on particular ports to particular IP addresses. The most current list of outbound ports and IP addresses
for your particular organization can be found here.
Assigning IP Addresses to MR76s
All gateway MR76s (MR76s with Ethernet connections to the LAN) must be assigned routable IP addresses. These IP addresses can be dynamically assigned
via DHCP or statically assigned.
Dynamic Assignment (Recommended)
When using DHCP, the DHCP server should be configured to assign a static IP address for each MAC address belonging to a Meraki AP. Other
features of the wireless network, such as 802.1X authentication, may rely on the property that the APs have static IP addresses.
7
Static Assignment
Static IPs are assigned using the local web server on each AP. The following procedure describes how to set the static IP:
1. Using a client machine (e.g., a laptop), connect to the AP wirelessly (by associating to any SSID broadcast
by the AP) or over a wired connection.
2. If using a wired connection, connect the client machine to the MR76 either through a PoE switch or a PoE
Injector. If using a PoE switch, plug an Ethernet cable into the MR76’s Ethernet jack, and the other end into
a PoE switch. Then connect the client machine over Ethernet cable to the PoE switch. If using a PoE
Injector, connect the MR76 to the “PoE” port of the Injector, and the client machine to the “LAN” port.
3. Using a web browser on the client machine, access the AP’s built-in web server by browsing
to http://my.meraki.com. Alternatively, browse to http://10.128.128.128.
4. Click on the “Uplink Configuration” tab. Log in. The default login is the serial number (e.g. Qxxx-xxxx-xxxx),
with no password (e.g., Q2DD-551C-ZYW3).
5. Configure the static IP address, net mask, gateway IP address and DNS servers that this AP will use on its
wired connection.
6. If necessary, reconnect the AP to the LAN.
Static IP via DHCP Reservations
Instead of associating to each Meraki AP individually to configure static IP addresses, an administrator can assign static IP addresses on the upstream
DHCP server. Through “DHCP reservations,” IP addresses are “reserved” for the MAC addresses of the Meraki APs. Please consult the documentation
for the DHCP server to configure DHCP reservations.
Collect ools
You will need the following tools to perform an installation:
8
Collect Additional Hardware for Installation
You will need the following tools to perform an installation:
• Network cables with RJ45 connectors long enough for your particular mounting location
• 802.3af PoE power source (either PoE switch or Meraki PoE Injector)
• Connection to the internet (if you are setting up your MR76 as a gateway to the internet)
• Appropriately sized metal straps (if mounting to a pole larger than 3.9” in diameter)
• Specialized mounting hardware if mounting to surface other than wood, stucco or stone
Installation Instructions
Warning: Due to the heat dissipation in the back of APs during normal operation, please do not stack powered on APs on top of each other during
pre-installation to avoid heat damage.
9
Choose Your Mounting Location
A good mounting location is important to getting the best performance out of your MR76 access point. Keep the following in mind:
1. The device should have unobstructed line of sight to most coverage areas.
2. Power over Ethernet supports a maximum cable length of 300 ft (100 m).
3. If being used in a mesh deployment, the MR76 should have line of sight to at least two other Meraki devices.
4. The antennas should be as unobstructed as possible. Make sure that there is clearance around the MR76 for
installation of all of your chosen antennas.
Install the MR76
For most mounting scenarios, the MR76 mount cradle provides a quick, simple, and flexible means of mounting your device. The installation should be done in
two steps. First, install the mount cradle to your selected location. Then, attach the MR76 to the mount cradle.
Remove the Mount Plate from the Access Point
Before installing the mount plate, you must remove it from the back of the access point.
1. Unscrew the mount plate attachment screw.
2. Lift the mount plate release tab upwards.
3. While holding the mount plate release tab up, slide the mount plate off the access point in the direction shown
below.
Attach the mount cradle
The MR76 mount plate can be used to install your access point in a wide range of scenarios.
Wall or Solid Ceiling Mount Using mount cradle
Using included wall anchors and screws, attach the mount plate to your mounting wall or ceiling.
10
Inhaltsverzeichnis
Andere Cisco Drahtloser Zugangspunkt Handbücher
Cisco
Cisco Aironet 1570 Series Handbuch
Cisco
Cisco WAP200 - Small Business Wireless-G Access... Bedienungsanleitung
Cisco
Cisco M10-RM Kurzanleitung
Cisco
Cisco Catalyst 9164 Series Bedienungsanleitung
Cisco
Cisco 1130AG - Aironet - Wireless Access Point Handbuch
Cisco
Cisco Wap581 Bedienungsanleitung
Cisco
Cisco AIR-AP1041N-A-K9 Bedienungsanleitung
Cisco
Cisco WAP4410N - Small Business Wireless-N Access... Bedienungsanleitung
Cisco
Cisco Catalyst 9117AX Series Bedienungsanleitung
Cisco
Cisco Aironet 1815T Bedienungsanleitung
Cisco
Cisco Catalyst IW9167E Handbuch
Cisco
Cisco Aironet 1600 Series Kurzanleitung
Cisco
Cisco Aironet 1530 Bedienungsanleitung
Cisco
Cisco Meraki MR20-HW Bedienungsanleitung
Cisco
Cisco Meraki MR55-HW Handbuch
Cisco
Cisco Linksys WAP54GX Original Betriebsanleitung
Cisco
Cisco Aironet 1520 Series Bedienungsanleitung
Cisco
Cisco Small Business AP541N Bedienungsanleitung
Cisco
Cisco AIR-CAP3502I-A-K9 Bedienungsanleitung
Cisco
Cisco MERAKI MR66 Bedienungsanleitung
Beliebte Drahtloser Zugangspunkt Handbücher anderer Marken
D-Link
D-Link DWL-2100AP - AirPlus Xtreme G Bedienungsanleitung
Ubiquiti
Ubiquiti NanoStation NSM2 Bedienungsanleitung
Aruba
Aruba IAP-335 Bedienungsanleitung
Advantek Networks
Advantek Networks AWN-AP-54MR Bedienungsanleitung
IP-COM
IP-COM AP355 Bedienungsanleitung
Buffalo
Buffalo AirStation WLA-L11G Bedienungsanleitung
