Cisco Aironet 1240AG Series Bedienungsanleitung
1
Quick Start Guide Cisco Aironet 1240AG Series Access Point
Read This First
Note If you purchased a 1242G access point, this quick start guide refers
occasionally to an 802.11a radio. However, your 1242G access point
does not contain an 802.11a radio; it only contains an 802.11b or
802.11g radio. Please disregard the sections in your quick start guide
that refer specifically to an 802.11a radio.
You should review this table and the instructions for opening the top cover.
The table contains important information that you need to know so that you
can successfully configure your access point.
Setting Default
Login Cisco (case sensitive)
Password Cisco (case sensitive)
IP address Determined by DHCP server
Service Set Identifier (SSID) See the “Radio and IP Address
Configuration” section on page 2.
2
OL-16714-01
Radio and IP Address Configuration
The access point ships with its radio disabled and no assigned IP address or
service set identifier (SSID). You must enable them when you configure the
access point for the first time. The access point no longer is assigned an IP
address. It is configured to obtain an IP address by using a DHCP server. If
your network does not use a DHCP server, you must connect to the access
point console port and assign a static IP address (See the “Assigning an IP
Address Using the CLI” section on page 20.
Status LED Status Description
Blue Normal operating condition and at
least one wireless client device is
associated with the access point.
Light green Normal operating condition, but no
wireless client devices are
associated with the access point.
Amber or red Error condition. See the “Checking
the Access Point LEDs” section on
page 42.
3
Quick Start Guide Cisco Aironet 1240AG Series Access Point
Before You Start
Before you install the access point, make sure that you are using a computer
connected to the same network as the access point, and obtain the following
from your network administrator:
•A host name for the access point
•The case-sensitive SSID for your radio 802.11g and 802.11a radio
networks
•A Simple Network Management Protocol (SNMP) community name and
the SNMP file attribute (if SNMP is in use)
•The Media Access Control (MAC) address from the label on the bottom
of the access point (such as 0016462584c), if you plan to use the Cisco
IP Setup Utility to find an access point IP address.
•If you are not connected to a DHCP server, you can assign an IP address
to the access point using the CLI. In this situation, obtain a unique IP
address for your access point, a default gateway, and subnet mask from
your network system administrator.
4
OL-16714-01
Safety Information
The FCC with its action in ET Docket 96-8 has adopted a safety standard for
human exposure to radio frequency (RF) electromagnetic energy emitted by
FCC certified equipment. When used with approved Cisco Aironet antennas,
Cisco Aironet products meet the uncontrolled environmental limits found in
OET-65 and ANSI C95.1, 1991. Proper installation of this radio according to
the instructions found in this manual will result in user exposure that is
substantially below the FCC recommended limits.
•Do not hold any component containing a radio so that the antenna is very
close to or touching any exposed parts of the body, especially the face or
eyes, while transmitting.
•The use of wireless devices in hazardous locations is limited to the
constraints posed by the safety directors of such environments.
Warnings
Translated versions of the following safety warnings are provided in
Appendix A of the Cisco Aironet 1240AG Series Access Point Hardware
Installation Guide.
5
Quick Start Guide Cisco Aironet 1240AG Series Access Point
Warning
Read the installation instructions before you connect the
system to its power source.
Statement 1004
Warning
This product must be connected to a power-over-ethernet
(PoE) IEEE 802.3af compliant power source or an IEC60950
compliant limited power source.
Statement 353
Warning
This product relies on the building’s installation for
short-circuit (overcurrent) protection. Ensure that the
protective device is rated not greater than:
20A
Statement 1005
Warning
Do not operate your wireless network device near unshielded
blasting caps or in an explosive environment unless the
device has been modified to be especially qualified for such
use.
Statement 245B
6
OL-16714-01
Warning
In order to comply with FCC radio frequency (RF) exposure
limits, antennas should be located at a minimum of 7.9 inches
(20 cm) or more from the body of all persons.
Statement 332
Warning
Do not work on the system or connect or disconnect cables
during periods of lightning activity.
Statement 1001
Overview
This guide is designed to help you minimally configure a Cisco Aironet
1240AG Series Access Point by using its GUI through your web browser. The
GUI is the primary configuration tool. Configuration can also be performed
by using the command-line interface (CLI). For instructions on using the CLI,
see the Cisco IOS Software Configuration Guide for Cisco Aironet Access
Points.
7
Quick Start Guide Cisco Aironet 1240AG Series Access Point
Note Configuring your access point by using Cisco’s Structured
Wireless-Aware Network (SWAN) or Cisco’s Wireless LAN
Solution Engine (WLSE) is not covered in this guide. Refer to the
appropriate SWAN or WLSE documentation for configuration
information. These documents are also available on Cisco.com.
8
OL-16714-01
This table lists documents related to the 1240AG series access point.
These documents are on Cisco.com at the following URL:
http://www.cisco.com/en/US/products/ps6521/tsd_products_support_series_
home.html
Topic Document
Performing an advanced
configuration
Cisco IOS Software Configuration Guide for
Cisco Aironet Access Points
Cisco Aironet Command Reference for Cisco
Aironet Access Points and Bridges
Mounting the access point Cisco Aironet 1240AG Series Access Point
Hardware Installation Guide
System requirements,
important notes,
limitations, and
last-minute updates
Release Notes for Cisco Aironet 1240AG
Series Access Points for Cisco IOS Release
12.3(7)JA (or later)
9
Quick Start Guide Cisco Aironet 1240AG Series Access Point
Unpacking the Access Point
Follow these steps to unpack the access point:
1. Open the shipping container and carefully remove the contents.
2. Return all packing materials to the shipping container and save it.
3. Ensure that all items listed in the Package Contents section are included
in the shipment. Check each item for damage. If any item is damaged or
missing, notify your authorized Cisco sales representative.
Package Contents
Each access point package contains the following items:
•Cisco Aironet 1240AG Series Access Point
•Cisco Aironet 1240AG Series Power Module (universal power
module)—optional
•Mounting hardware kit
10
OL-16714-01
•One mounting plate
–
Cable security bracket
–
Two suspended ceiling T-rail clips (accommodates standard and
recessed T-rails)
–
One security hasp
–
Four 6 x 32 x ½ in. pan head Phillips machine screws
–
One 8 x 18 x ¾ in. pan head Phillips sheet metal screws
–
2 #8 plastic wall anchors
–
One 10 x 24 nut (for ground stud on mounting bracket)
–
Four rubber foot pads
–
Two cable tie wraps
•Quick Start Guide: Cisco Aironet 1240AG Series Access Point
•Safety Warnings for Cisco Aironet 1240AG Series Access Points
•Cisco product registration and Cisco documentation feedback cards
The following illustrations show the access point with its external antennas
connected.
Andere Handbücher für Aironet 1240AG Series
2
Inhaltsverzeichnis
Andere Cisco Drahtloser Zugangspunkt Handbücher
Cisco
Cisco Aironet 1520 Series Bedienungsanleitung
Cisco
Cisco Catalyst IW6300 Series Bedienungsanleitung
Cisco
Cisco Aironet OfficeExtend AIR-OEAP602I-E-K9 Bedienungsanleitung
Cisco
Cisco AT&T U-VERSE VEN401 Bedienungsanleitung
Cisco
Cisco Aironet 1240AG Series Handbuch
Cisco
Cisco 7330 Bedienungsanleitung
Cisco
Cisco Small Business AP541N Bedienungsanleitung
Cisco
Cisco Aironet 1600 Series Kurzanleitung
Cisco
Cisco Small Business WAP551 Bedienungsanleitung
Cisco
Cisco Meraki MR42 Bedienungsanleitung
Cisco
Cisco Meraki CW9163E Bedienungsanleitung
Cisco
Cisco Meraki MR45 Bedienungsanleitung
Cisco
Cisco WAP125 Service-Handbuch
Cisco
Cisco WAP571E Bedienungsanleitung
Cisco
Cisco Meraki MR46 Bedienungsanleitung
Cisco
Cisco Aironet 3500 Series Bedienungsanleitung
Cisco
Cisco WAP121 Bedienungsanleitung
Cisco
Cisco MERAKI MR46E-HW Handbuch
Cisco
Cisco Meraki Go GR62 Bedienungsanleitung
Cisco
Cisco Aironet 1250 Series Handbuch
Beliebte Drahtloser Zugangspunkt Handbücher anderer Marken
D-Link
D-Link DWL-2100AP - AirPlus Xtreme G Bedienungsanleitung
Ubiquiti
Ubiquiti NanoStation NSM2 Bedienungsanleitung
Aruba
Aruba IAP-335 Bedienungsanleitung
Advantek Networks
Advantek Networks AWN-AP-54MR Bedienungsanleitung
IP-COM
IP-COM AP355 Bedienungsanleitung
Buffalo
Buffalo AirStation WLA-L11G Bedienungsanleitung
