Cisco Meraki MR78 Bedienungsanleitung
• Mount cradle including built-in level tool
2
• Mount Kit
◦ Wall screws and wall screw anchors
Understanding the MR78
Your Meraki MR78 has the following features:
3
The mount cradle has the following features:
4
Security Features
The MR78 allows for physically securing the access point after installation:
1. Security screw – The accessory kit includes screws that can be used to secure the access point to the mount
cradle. Engaging the security screw prevents accidental dislodging and theft.
Ethernet Ports
The MR78 features a Gigabit Ethernet RJ45 port that accepts 802.3at and 802.3af power (labeled “Eth0, PoE”). This
port should be used for uplink to your WAN connection.
Power Source Options
The MR78 access point can be powered using either the Meraki AC Adapter, PoE Injector (both sold separately), or a
third-party PoE switch. The MR78 operates at full power with 802.3af PoE.
Factory Reset Button
If the button is pressed and held for at least five seconds and then released, the MR78 will reboot and be restored to its
original factory settings by deleting all configuration information stored on the unit.
ED Indicators and Run Dark Mode
Your MR78 is equipped with a multi-color ED light on the front of the unit to convey information about system
functionality and performance:
• Orange - AP is booting (permanent Orange suggests hardware issue)
• Rainbow - AP is initializing/scanning
• Blinking Blue - AP is upgrading
• Green - AP in Gateway mode with no clients
• Blue - AP in Gateway mode with clients
• Blinking Orange - AP can't find uplink
5
NOTE: Blinking Green ED indicates that the device is in site survey mode. Please see the Conducting Site Surveys
with MR Access Points for more details.
The MR78 may be operated in “Run Dark” mode for additional security and to reduce the visibility of the access point. In
this mode, the ED will not be illuminated. This mode may be enabled through Meraki dashboard.
Pre-Install Preparation
You should complete the following steps before going on-site to perform an installation.
Configure Your Network in Dashboard
The following is a brief overview only of the steps required to add an MR78 to your network. For detailed instructions
about creating, configuring and managing Meraki wireless networks, refer to the online documentation
(documentation.meraki.com).
1. ogin to http://dashboard.meraki.com. If this is your first time, create a new account.
2. Find the network to which you plan to add your APs or create a new network.
3. Add your APs to your network. You will need your Meraki order number (found on your invoice) or the serial
number of each AP, which looks like Qxxx-xxxx-xxxx, and is found on the bottom of the unit. You will also need
your Enterprise license key, which you should have received via email.
4. Go to the map / floor plan view and place each AP on the map by clicking and dragging it to the location where you
plan to mount it.
Check and Upgrade Firmware
To ensure your MR78 performs optimally immediately following installation, it is recommended that you facilitate a
firmware upgrade prior to mounting your MR78.
1. Attach your MR78 to power and a wired Internet connection. See the "Power the MR78" section for details.
2. The MR78 will turn on and the ED will glow solid orange. If the unit does not require a firmware upgrade, the ED
6
will turn either green (no clients associated) or blue (clients associated) within thirty seconds.
* If the unit requires an upgrade, the ED will begin blinking orange until the upgrade is complete, at which point the ED
will turn solid green or blue. You should allow at least a few minutes for the firmware upgrade to complete, depending on
the speed of your internet connection.
Check and Configure Firewall Settings
If a firewall is in place, it must allow outgoing connections on particular ports to particular IP addresses. The most
current list of outbound ports and IP addresses for your particular organization can be found here.
Assigning IP Addresses to MR78s
All gateway MR78s (MR78s with Ethernet connections to the AN) must be assigned routable IP addresses. These IP
addresses can be dynamically assigned via DHCP or statically assigned.
Dynamic Assignment
When using DHCP, the DHCP server should be configured to assign a static IP address for each MAC address
belonging to a Meraki AP. Other features of the wireless network, such as 802.1X authentication, may rely on the
property that the APs have static IP addresses.
Static Assignment
Static IPs are assigned using the local web server on each AP. The following procedure describes how to set the
static IP:
1. Using a client machine (e.g., a laptop), connect to the AP wirelessly (by associating to any SSID
broadcast by the AP) or over a wired connection.
2. If using a wired connection, connect the client machine to the MR78 either through a PoE switch or a
PoE Injector. If using a PoE switch, plug an Ethernet cable into the MR78’s Ethernet jack, and the other
end into a PoE switch. Then connect the client machine over Ethernet cable to the PoE switch. If using a
PoE Injector, connect the MR78 to the “PoE” port of the Injector, and the client machine to the “ AN”
port.
3. Using a web browser on the client machine, access the AP’s built-in web server by browsing
to http://my.meraki.com. Alternatively, browse to http://10.128.128.128.
4. Click on the “Uplink Configuration” tab. og in. The default login is the serial number (e.g. Qxxx-xxxx-
xxxx), with no password (e.g., Q2DD-551C-ZYW3).
5. Configure the static IP address, net mask, gateway IP address and DNS servers that this AP will use on
its wired connection.
6. If necessary, reconnect the AP to the AN.
Static IP via DHCP Reservations
Instead of associating to each Meraki AP individually to configure static IP addresses, an administrator can
assign static IP addresses on the upstream DHCP server. Through “DHCP reservations,” IP addresses are
7
“reserved” for the MAC addresses of the Meraki APs. Please consult the documentation for the DHCP server to
configure DHCP reservations.
Collect Tools
You will need the following tools to perform an installation:
Collect Additional Hardware for Installation
You will need the following hardware to perform an installation:
Installation Instructions
Warning: Due to the heat dissipation in the back of APs during normal operation, please do not stack powered on APs
on top of each other during pre-installation to avoid heat damage.
8
Choose Your Mounting ocation
A good mounting location is important to getting the best performance out of your MR78 access point. Keep the
following in mind:
1. The device should have unobstructed line of sight to most coverage areas. For example, if installing in an office
filled with workspaces divided by mid-height cubicle walls, installing on the ceiling or high on a wall would be ideal.
2. Power over Ethernet supports a maximum cable length of 300 ft (100 m).
3. If being used in a mesh deployment, the MR78 should have line of sight to at least two other Meraki devices. A
Cisco Partner can help ensure that your AP placement is ideal.
Install the MR78
For most mounting scenarios, the MR78 mount cradle provides a quick, simple, and flexible means of mounting your
device. The installation should be done in two steps. First, install the mount cradle to your selected location. Then,
attach the MR78 to the mount cradle.
Attach the Mount Cradle
The MR78 mount cradle can be used to install your access point on a wall, solid ceiling, or pole.
Wall or Solid Ceiling Mount Using Mount Cradle
Using included wall anchors and screws, attach the mount cradle to your mounting wall or ceiling. It is
recommended that the MR78 be mounted to a wall or solid ceiling using the mount cradle for physical security
reasons.
Pole Mount Using Mount Cradle
Use mounting straps (not included) to secure the mount cradle to a pole. Thread the mounting straps through the
mounting strap slots to secure the mount plate in a horizontal or vertical orientation. Vertical orientation is
recommended for optimal RF coverage.
Connect Access Point to Ethernet and/or AC Adapter
Using a phillips head screwdriver, remove the screws that secure the Ethernet cover. Ensure that the Ethernet cable
(and power cable, if applicable) is properly secured in the black cable gland. Secuire the Ethernet cover with the phillips
head screwdriver.
Mount the MR78
9
Attach the MR78 to the Mount Cradle
(This section applies to wall and/or solid ceiling where you have already installed the mount cradle.)
The MR78 attaches to the mount cradle with two tabs on the cradle that insert into the MR78, and is secured to the
cradle using one screw.
To attach the MR78 to the mount cradle properly, line up the top edge of the AP with the top tab of the mount cradle.
Since the cradle is already mounted to the wall, guide the MR78 towards the top tab and insert the top tab into the
MR78’s slot.
Then, adjust the MR78 to guide the MR78’s bottom slot into the cradle’s bottom tab until it clicks into place. Once in
place, the MR78 should be secured to the cradle by using one of the included screws in the cradle’s bottom tab.
10
Inhaltsverzeichnis
Andere Cisco Drahtloser Zugangspunkt Handbücher
Cisco
Cisco 1262 Bedienungsanleitung
Cisco
Cisco Aironet 340 Series Handbuch
Cisco
Cisco Aironet 1850 Series Kurzanleitung
Cisco
Cisco Aironet AIR-AP1252AG-A-K9 Handbuch
Cisco
Cisco Meraki MR33 Bedienungsanleitung
Cisco
Cisco Meraki MR70 Bedienungsanleitung
Cisco
Cisco Catalyst IW9165D Handbuch
Cisco
Cisco AIR-AP1010 - 1000 Series Lightweight Access... Bedienungsanleitung
Cisco
Cisco 1130AG - Aironet - Wireless Access Point Handbuch
Cisco
Cisco Aironet 1600 Series Kurzanleitung
Cisco
Cisco Aironet 1200 Series Installations- und Betriebshandbuch
Cisco
Cisco Linksys WAP55AG Bedienungsanleitung
Cisco
Cisco Catalyst Wireless 9162I Series Handbuch
Cisco
Cisco AIR-LMC352 Bedienungsanleitung
Cisco
Cisco Aironet 1240AG Series Handbuch
Cisco
Cisco 1242AG - Aironet - Wireless Access Point Handbuch
Cisco
Cisco Aironet 3500 Series Bedienungsanleitung
Cisco
Cisco Aironet 2802E Bedienungsanleitung
Cisco
Cisco Aironet 1700 Kurzanleitung
Cisco
Cisco Aironet 350 Series Handbuch
Beliebte Drahtloser Zugangspunkt Handbücher anderer Marken
D-Link
D-Link DWL-2100AP - AirPlus Xtreme G Bedienungsanleitung
Ubiquiti
Ubiquiti NanoStation NSM2 Bedienungsanleitung
Aruba
Aruba IAP-335 Bedienungsanleitung
Advantek Networks
Advantek Networks AWN-AP-54MR Bedienungsanleitung
IP-COM
IP-COM AP355 Bedienungsanleitung
Buffalo
Buffalo AirStation WLA-L11G Bedienungsanleitung
