Cisco Aironet 3800P Series Bedienungsanleitung

GETTING STARTED GUIDE

Cisco Aironet 3800P Series Access Points

First Published: February 22, 2016

1About this Guide

2About the Access Point

3Safety Instructions

4Unpacking

5AP Views, Ports, and Connectors

6Preparing the AP for Installation

7Installation Overview

8Performing a Pre-Installation Configuration

9Mounting and Grounding the Access Point

10 Powering the Access Point

11 Configuring and Deploying the Access Point

12 Checking the Access Point LEDs

13 Miscellaneous Usage and Configuration Guidelines

14 Related Documentation

15 Declarations of Conformity and Regulatory Information

16 Obtaining Documentation and Submitting a Service Request

1 About this Guide

This guide provides instructions on how to install your Cisco Aironet 3800P series access point and

provides links to resources which can help you configure the access point. This guide provides

mounting instructions and limited troubleshooting procedures.

The 3800P series access point is referred to as access point or AP in this document.

2 About the Access Point

The Cisco Aironet 3800P series Wi-Fi access point provides 802.11ac Wave 2 with Multi User MIMO

(MU MIMO). This AP offers dual-band radios (2.4 GHz and 5 GHz) with external antenna options.

The series supports high-performing Spectrum Intelligence which sustains three spatial stream rates

over a deployable distance with high reliability when serving clients. The access point supports full

inter-interoperability with leading 802.11ac clients, and support a mixed deployment with other access

points and controllers.

A full listing of the access point's features and specification are provided in the Cisco Aironet 3800

Series Access Point Data Sheet, at the following URL:

(URL will be added when available, before FCS)

Access Point Features

The 3800 series access point is a Dual-band, controller-based 802.11a/g/n/ac AP and supports:

• Simultaneous dual-band (2.4-GHz and 5-GHz) radios.

• Deployment in indoor environments, with external antennas (AIR-AP3802P-x-K9).

The ‘x’ in the model numbers represents the regulatory domain.

You need to verify whether the AP model you have is approved for use in your country. To verify

approval and to identify the regulatory domain that corresponds to a particular country, visit

http://www.cisco.com/go/aironet/compliance. Not all regulatory domains have been approved. As

and when they are approved, this compliance list will be updated.

• Multi-Gigabit Ethernet (mGig) Support, providing multiple gigabit uplink speeds of 2.5G and 5G

in addition to 100M and 1G speeds.

• Radio Role Flexibility, allowing for either manual configuration or for the APs to intelligently

determine the operating role of the integrated radios based on the available RF environment. The

AP can operate in the following modes:

–

2.4GHz and 5GHz role, where one radio serves clients in 2.4GHz mode, while the other serves

clients in 5GHz mode.

–

Dual 5GHz role, with both radios operating in the 5GHz band, actively serving client devices

to maximize the benefits of 802.11ac wave 2 and to increase client device capacity.

–

Wireless Security Monitoring and 5GHz role, where one radio serves 5GHz clients, while the

other radio scans both 2.4GHz and 5GHz for wIPS attackers, CleanAir interferers, and rogue

devices.

• Cross-AP Noise Reduction, a Cisco innovation that enables APs to intelligently collaborate in real

time about RF conditions so that users connect with optimized signal quality and performance.

• Optimized AP Roaming for ensuring that client devices associate with the AP in their coverage

range that offers the fastest data rate available.

• Cisco ClientLink 4.0 technology for improved downlink performance to all mobile devices,

including one-, two-, and three-spatial-stream devices up to 802.11ac Wave 1 and Wave 2. The

technology also improves battery life on mobile devices.

• Cisco CleanAir technology enhanced with 160MHz channel support. CleanAir delivers proactive,

high-speed spectrum intelligence across 20-, 40-, and 80-, and 160-MHz-wide channels to combat

performance problems arising from wireless interference.

• MIMO equalization capabilities, which optimize uplink performance and reliability by reducing

the impact of signal fade.

Antennas and Radios

The 3800 series access point contains two simultaneous dual-band radios, the 2.4GHz and 5GHz

MU-MIMO radio, and the 5-GHz 802.11ac MU-MIMO radio. The 3800P series access point

(AIR-AP3802P-x-K9) has two 2.4-GHz/5-GHz dual-band radios, up to 4 external dual-band dipole

antennas.

The radio and antennas support frequency bands 2400–2500 MHz and 5180–5865 MHz through a

common dual-band RF interface. Features of the external dual-band dipole antennas are:

• Four RTNC antenna connectors on the top of the access point

• Four TX/RX antennas

Supported External Antennas

Frequency Part Number Antenna Type

2.4GHz AIR-ANT24020V-R

AIR-ANT2452V-R Diversity Omni-directional

AIR-ANT2430V-R MIMO 3-Element Omni

AIR-ANT2440NV-R MIMO Wall-Mount Omni Antenna

AIR-ANT2460NP-R MIMO 3-Element Patch

5GHz AIR-ANT5140V-R MIMO 3-Element Omni

AIR-ANT5140NV-R MIMO Wall-Mount Omni Antenna

AIR-ANT5145V-R Diversity Omni-directional

AIR-ANT5160NP-R MIMO 3-Element Patch

2.4GHz and 5GHz AIR-ANT2451V-R

AIR-ANT2451NV-R

AIR-ANT2524DB-R Dual-resonant black dipole

AIR-ANT2524DW-R Dual-resonant white dipole

AIR-ANT2524DG-R Dual-resonant gray dipole

AIR-ANT2524V4C-R Dual-resonant ceiling mount omni (4-pack)

AIR-ANT2535SDW-R Dual-resonant "stubby" monopole

AIR-ANT2544V4M-R Dual-resonant omni (4-pack)

AIR-ANT2566P4W-R Dual-resonant "directional" antenna

(4-pack)

AIR-ANT2566D4M-R Dual-Band Polarization-Diverse Directional

Array

AIR-ANT2513P4M-N Dual-resonant cross-pol "directional"

antenna (4-pack)

For additional details on the supported antennas, such as antenna gain, and information such as

channels and maximum power settings, see the Channels and Maximum Power Settings for Cisco 3800

Series Access Points sheet at the following URL:

(To be added when available, before FCS)

3 Safety Instructions

Translated versions of the following safety warnings are provided in the translated safety warnings

document that is shipped with your access point. The translated warnings are also in the Translated

Safety Warnings for Cisco Aironet Access Points, which is available on Cisco.com.

Warning

IMPORTANT SAFETY INSTRUCTIONS



This warning symbol means danger. You are in a situation that could cause bodily injury.

Before you work on any equipment, be aware of the hazards involved with electrical

circuitry and be familiar with standard practices for preventing accidents. Use the

statement number provided at the end of each warning to locate its translation in the

translated safety warnings that accompanied this device.

Statement 1071



SAVE THESE INSTRUCTIONS

Warning

Read the installation instructions before you connect the system to its power source.

Statement 1004

Warning

Installation of the equipment must comply with local and national electrical codes.

Statement 1074

Warning

This product relies on the building’s installation for short-circuit (overcurrent)

protection. Ensure that the protective device is rated not greater than:



20A.

Statement 1005

Warning

Do not operate your wireless network device near unshielded blasting caps or in an

explosive environment unless the device has been modified to be especially qualified for

such use.

Statement 245B

Warning

In order to comply with FCC radio frequency (RF) exposure limits, antennas should be

located at a minimum of 7.9 inches (20 cm) or more from the body of all persons.



Statement 332

Caution The fasteners you use to mount an access point on a ceiling must be capable of

maintaining a minimum pullout force of 20 lbs (9 kg) and must use all 4 indented holes

on the mounting bracket.

Caution This product and all interconnected equipment must be installed indoors within the same

building, including the associated LAN connections as defined by Environment A of the

IEEE 802.af Standard.

Note The access point is suitable for use in environmental air space in accordance with section

300.22.C of the National Electrical Code and sections 2-128, 12-010(3), and 12-100 of the

Canadian Electrical Code, Part 1, C22.1. You should not install the power supply or power

injector in air handling spaces.

Note Use only with listed ITE equipment.

4 Unpacking

To unpack the access point, follow these steps:

Step 1 Unpack and remove the access point and the accessory kit from the shipping box.

Step 2 Return any packing material to the shipping container and save it for future use.

Step 3 Verify that you have received the items listed below. If any item is missing or damaged, contact

your Cisco representative or reseller for instructions.

–

The access point

–

Mounting bracket (selected when you ordered the access point)

–

Adjustable ceiling-rail clip (selected when you ordered the access point)

5 AP Views, Ports, and Connectors

Figure 1 Face of the AP

1Dual-band antenna connector A. 5Location of the ports and connectors on the

head of the AP.

2Dual-band antenna connector B. 6Status LED.

3Dual-band antenna connector C. 7Location of the module connector port on

the base of the AP.

4Dual-band antenna connector D.

The ports and connections on the bottom of the access point are shown in Figure 2.

Figure 2 Access Point Ports and Connections on the Head

1Kensington lock slot. 5

2Mode button. 6

3Gigabit Ethernet port. 7DC power port.

4USB port.

Figure 3 AP Module Connector Port on the Base

Inhaltsverzeichnis

Andere Cisco Drahtloser Zugangspunkt Handbücher

Cisco

Cisco Wap581 Bedienungsanleitung

Cisco

Cisco WAP2000 Bedienungsanleitung

Cisco

Cisco ASA 5506W-X Bedienungsanleitung

Cisco

Cisco WAP121 Bedienungsanleitung

Cisco

Cisco Catalyst 9136I Series Bedienungsanleitung

Cisco

Cisco CW91641-A Handbuch

Cisco

Cisco Catalyst 9130 Bedienungsanleitung

Cisco

Cisco Catalyst Wireless 9162I Series Handbuch

Cisco

Cisco Catalyst 9124AX Series Handbuch

Cisco

Cisco Aironet 1400 Series Handbuch

Cisco

Cisco WAP121 Bedienungsanleitung

Cisco

Cisco Cisco Aironet Wireless LAN Client Bedienungsanleitung

Cisco

Cisco WAP4410N - Small Business Wireless-N Access... Bedienungsanleitung

Cisco

Cisco WAP150 Bedienungsanleitung

Cisco

Cisco Catalyst IW9167E Handbuch

Cisco

Cisco WAP371 Bedienungsanleitung

Cisco

Cisco Meraki MR36 Bedienungsanleitung

Cisco

Cisco GR10-HW-EU Bedienungsanleitung

Cisco

Cisco Meraki MR84 Handbuch

Cisco

Cisco Catalyst 9136I Series Handbuch

Cisco

Cisco AIR-AP1131G-A-K9 Bedienungsanleitung

Cisco

Cisco Aironet 600 Series Bedienungsanleitung

Cisco

Cisco Aironet 3700 Series Kurzanleitung

Cisco

Cisco 1552S Bedienungsanleitung

Beliebte Drahtloser Zugangspunkt Handbücher anderer Marken

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Bedienungsanleitung

Ubiquiti

Ubiquiti NanoStation NSM2 Bedienungsanleitung

Aruba

Aruba IAP-335 Bedienungsanleitung

Advantek Networks

Advantek Networks AWN-AP-54MR Bedienungsanleitung

IP-COM

IP-COM AP355 Bedienungsanleitung

Buffalo

Buffalo AirStation WLA-L11G Bedienungsanleitung

EnGenius

EnGenius EnStationACv2 Bedienungsanleitung

D-Link

D-Link DAP-3662 Bedienungsanleitung

xG Technology

xG Technology xMax CN1300 Bedienungsanleitung

Widelink

Widelink ezWave WAP-1100 Series Bedienungsanleitung

Edimax

Edimax CAP1200 Bedienungsanleitung

Ubiquiti

Ubiquiti LBE-5AC-Gen2 Bedienungsanleitung

Aruba

Aruba AP-203R Bedienungsanleitung

LuXout Shades

LuXout Shades LUXSHADE MOTION Bedienungsanleitung

CreatComm

CreatComm TB5F Bedienungsanleitung

SineDigital

SineDigital MW-1500AP(H) Bedienungsanleitung

TP-Link

TP-Link AP9650 V1 Bedienungsanleitung

Draytek

Draytek VIGORAP 902 Bedienungsanleitung