Cisco WAP121 Bedienungsanleitung

Reboot and Factory Default Reset on

WAP121 and WAP321 Access Points

Objective

This article explains how to perform a standard reboot and also how to reset to factory

default on the WAP121 and WAP321 access points. Reboot or restart of the network

device is made when certain changes in the settings need a reboot or if the device is

frozen. Consequences of reboot will result in the deletion of logs in volatile memory.

The configuration settings of the network device gets reflected after the restart. Factory

default reset is used to remove the running/current configuration settings on the

network device and to restore it to the original default settings. Factory default reset is

recommended when the whole device needed to be reconfigured and also in case if

you forget the password and not able to recover by any means such as telnet.

Applicable Devices | Firmware Version

WAP121 | 1.0.3.4 (Download latest)

●

WAP321 | 1.0.3.4 (Download latest)

●

Reset to Factory Default

There are two ways to reset to factory default settings to the factory default

configuration:

Hardware Reset

●

Factory default reset by web configuration utility

●

Hardware Reset

Step 1. Hold the Reset button located at the back of the device for approximately ten

seconds with a pin.

The Access Point reloads and is set to the default configuration settings.

Step 2. Launch a web browser, such as Internet Explorer or Mozilla Firefox. Type the

default static IP address 192.168.1.245 in the URL bar and press enter. To reach that

IP address, be sure that your computer is on the 192.168.1.xxx network.

If your network has a DHCP server, then the factory default IP address configuration of the

WAP is DHCP. In the absence of a DHCP server, the access point will fallback to the

default static IP address after 60 seconds.

Step 3. Login with the default credentials.The default username is cisco, and the

default password is cisco.

Factory Default Reset by Web Configuration Utility

Step 1. Log in to the web configuration utility and choose Administration > Reboot.

The Reboot page opens:

Step 2. Click Reboot To Factory Default to reboot the access point and return the

device to factory default settings. Once rebooted to factory default, all saved

configurations will be lost.

Step 3. The Confirm window appears. Click OK to continue with the reboot to factory

default settings.

Reboot Access Point

There are two ways to reset the Access Point:

• Hardware reset

• Reset with the use of the web configuration utility

Reboot Access Point by Hardware

Step 1. Press the power button to turn off the device. After 10 seconds have passed,

press the power button a second time to power the device back on.

The Access Point reboots and is refreshed.

Reboot Access Point by Web Configuration Utility

Step 1. Log in to the web configuration utility and choose Administration > Reboot.

The Reboot page opens:

Step 2. Click Reboot to reboot the device.

Step 3. The confirm window appears. Click OK to continue with the reboot of the

device.

If you would like to read an article on this same topic, check out Reboot and Reset the

Wireless Access Point to Factory Default Settings.

Andere Handbücher für WAP121

9

Dieses Handbuch passt für folgende Modelle

1

Inhaltsverzeichnis

Andere Cisco Drahtloser Zugangspunkt Handbücher

Cisco

Cisco WAP150 Bedienungsanleitung

Cisco

Cisco Meraki GR60 Bedienungsanleitung

Cisco

Cisco Meraki MR42 Bedienungsanleitung

Cisco

Cisco AIR-AP352E2R - Aironet 350 - Wireless Access... Bedienungsanleitung

Cisco

Cisco 500 Series Bedienerhandbuch

Cisco

Cisco AIR-LMC352 Bedienungsanleitung

Cisco

Cisco AT&T U-VERSE VEN401 Bedienungsanleitung

Cisco

Cisco 1130AG - Aironet - Wireless Access Point Handbuch

Cisco

Cisco MERAKI MR66 Bedienungsanleitung

Cisco

Cisco aironet 2800 series Kurzanleitung

Cisco

Cisco Meraki Go GR12 Bedienungsanleitung

Cisco

Cisco Aironet 3502P Bedienungsanleitung

Cisco

Cisco Aironet Wave 2 Installationshandbuch

Cisco

Cisco 1130AG - Aironet - Wireless Access Point Bedienungsanleitung

Cisco

Cisco aironet 1524SB Montage- und Bedienungsanleitung

Cisco

Cisco Small Business AP541N Bedienungsanleitung

Cisco

Cisco USC 3330 Bedienungsanleitung

Cisco

Cisco WAP571 Bedienungsanleitung

Cisco

Cisco Aironet 1250 Series Handbuch

Cisco

Cisco Aironet 1530 Series, 1532 Bedienungsanleitung

Cisco

Cisco Meraki MR12 Bedienungsanleitung

Cisco

Cisco WAP121 Bedienungsanleitung

Cisco

Cisco WAP125 Bedienungsanleitung

Cisco

Cisco Catalyst IW9165D Handbuch

Beliebte Drahtloser Zugangspunkt Handbücher anderer Marken

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Bedienungsanleitung

Ubiquiti

Ubiquiti NanoStation NSM2 Bedienungsanleitung

Aruba

Aruba IAP-335 Bedienungsanleitung

Advantek Networks

Advantek Networks AWN-AP-54MR Bedienungsanleitung

IP-COM

IP-COM AP355 Bedienungsanleitung

Buffalo

Buffalo AirStation WLA-L11G Bedienungsanleitung

EnGenius

EnGenius EnStationACv2 Bedienungsanleitung

D-Link

D-Link DAP-3662 Bedienungsanleitung

xG Technology

xG Technology xMax CN1300 Bedienungsanleitung

Widelink

Widelink ezWave WAP-1100 Series Bedienungsanleitung

Edimax

Edimax CAP1200 Bedienungsanleitung

Ubiquiti

Ubiquiti LBE-5AC-Gen2 Bedienungsanleitung

Aruba

Aruba AP-203R Bedienungsanleitung

LuXout Shades

LuXout Shades LUXSHADE MOTION Bedienungsanleitung

CreatComm

CreatComm TB5F Bedienungsanleitung

SineDigital

SineDigital MW-1500AP(H) Bedienungsanleitung

TP-Link

TP-Link AP9650 V1 Bedienungsanleitung

Draytek

Draytek VIGORAP 902 Bedienungsanleitung