Clarke CLIPPJS Bedienungsanleitung

OPERATION & MAINTENANCE

INSTRUCTIONS

LS1116

POWER PACK & JUMP STARTER

MODEL NO: CLIPPJS

PART NO: 6487075

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

INTRODUCTION

Thank you for purchasing this CLARKE product.

Before attempting to use this product, please read this manual thoroughly and

follow the instructions carefully. In doing so you will ensure the safety of yourself

and that of others around you, and you can look forward to your purchase

giving you long and satisfactory service.

GUARANTEE

This product is guaranteed against faulty manufacture for a period of 12

months from the date of purchase. Please keep your receipt which will be

required as proof of purchase.

This guarantee is invalid if the product is found to have been abused or

tampered with in any way, or not used for the purpose for which it was

intended.

Faulty goods should be returned to their place of purchase, no product can

be returned to us without prior permission.

This guarantee does not effect your statutory rights.

ENVIRONMENTAL PROTECTION

Do not dispose of this product with general household waste. All

tools, accessories and packaging should be sorted, taken to a

recycling centre and disposed of according to the laws governing

Waste Electrical and Electronic Equipment.

SPECIFICATIONS

Model Number CLIPPJS

Battery Capacity 9.6Ah

Jumpstart Output Current Starting 200A / Peak 400A

USB Output 5V @ 2.1A

DC Output 12V @ 2A, 16V @ 3.5A, 19V @ 3.5A

Dimensions (L X W X H) 160 x 75 x 35 mm

Weight 0.73 kg

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

GENERAL SAFETY RULES

1. Although the unit is water resistant and may be used outdoors, DO NOT

leave it exposed to the elements. Avoid direct sunlight, direct heat, rain/

moisture etc. The power pack must only be used indoors or completely

protected from the rain. This also applies to any device being powered

by the power pack.

2. Do not operate the jumpstart if any of the cables are damaged. Consult

your Clarke dealer for repair or replacement of the parts.

3. Do not operate the unit if the case is damaged. Consult your Clarke

dealer or a qualified person for inspection and repair.

4. To prevent the battery from overheating and consequent damage, do

not exceed our recommendations for the duration of jump starting.

5. The unit is NOT designed to be used as a replacement for a vehicle

battery.

6. NEVER allow the battery to become completely discharged.

7. NEVER jump start the engine whilst the unit is being charged.

8. NEVER attempt any repairs yourself. If you have a problem with the unit

contact your local CLARKE dealer.

9. Always keep your body and clothing dry. Never work in a damp area

without adequate insulation against electric shock.

10. Always store the unit out of reach of children.

11. Always wear safety glasses when working with lead acid batteries.

12. If splashed by battery acid, immediately flush the area of the splash with

clean water. If a burning sensation is felt or any blistering occurs, seek

medical help.

13. If battery acid comes into contact with the eyes, flush the eyes with clean

water continuously and seek medical help.

14. Always ensure that there is air circulating around the unit when in use.

WARNING: ALL LEAD ACID BATTERIES GENERATE HYDROGEN GAS

DURING NORMAL OPERATION. THIS PROCESS INCREASES DURING A

PERIOD OF RAPID DISCHARGE, SUCH AS WHEN USING FOR

JUMPSTARTING.

WARNING: HYDROGEN GAS AND BATTERY ACID (SULPHURIC ACID) CAN

BE EXPLOSIVE, CORROSIVE TO SKIN, EYES AND HAIR, DAMAGING TO

CLOTHING AND METALS, FLAMMABLE, POISONOUS TO BREATHE.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

15. Never allow the jumpstart leads on this unit, to touch each other or to

touch the same metal object.

16. Ensure the vehicle battery posts and battery clamps are perfectly clean

before use.

17. Connect the red clamp to the unearthed battery terminal first, (this is

usually the positive (+ve) terminal and painted RED); then connect the

black clamp to the earthed battery terminal, (this is usually the negative (-

ve) terminal and painted BLACK).

18. ALWAYS wear suitable protective clothing and eye protection when

working with lead acid batteries.

19. NEVER allow the cables to become wrapped around the operator or any

other person.

ELECTRICAL CONNECTIONS

This product is provided with a 13 amp, 230 volt (50Hz), charging adaptor for

connection to a standard, domestic electrical supply. a 12V charging lead is

also supplied

This appliance is of double insulated design. No earth conductor is provided.

If in any doubt, consult a qualified electrician. DO NOT attempt any electrical

repairs yourself.

SAFETY SYMBOLS

Class II appliance Always read instructions

before use

Suitable for indoor use

only (refers to mains

adaptor only)

Subject to Waste Electrical

& Electronic Equipment

Directive

Live centre pin

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

OVERVIEW

NO DESCRIPTION NO DESCRIPTION

1 Worklight 5 Push Button

2 Jumpstart Lead Socket 6 USB Sockets 5V DC

3 Display 7 Charger Input Socket

4 DC Output Socket 8 ON/OFF Switch

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

CHARGING THE POWER PACK

You can charge your power pack using

either:

• The mains charger (A).

• The cigar lighter adapter (B).

1. Switch the power pack off.

2. Plug the mains charger or cigar

lighter adapter into the charger

input socket.

3. Connect the other end to either

the mains supply or cigar lighter

socket.

• If using the cigar lighter

adapter, start the engine first.

• The display will show the current charge percentage and the word

‘IN’.

4. When the display shows 100% disconnect the charger.

TO ENSURE MAXIMUM LIFE FROM THE BATTERY.

• Charge this unit before using it for the first time.

• Recharge after every use if possible, and thereafter, once every

three months.

• Never leave the unit in a state of discharge.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

OPERATION

USING THE WORKLIGHT

1. Set the ON/OFF switch to the ON

position.

2. Press and hold the push button for

3 seconds to turn the worklight on.

3. Press the push button again.

• The worklight will flash using the

morse code SOS pattern.

4. Press the push button again.

• The worklight will flash on and

off.

5. Press the push button again to turn the worklight off.

USING THE USB POWER SUPPLY

• This will supply a maximum of 2.1A at 5V.

1. Insert the USB cable into one of

the USB sockets on the side of the

power pack.

2. Plug the other end of the cable

into your device.

3. Set the ON/OFF switch to the ON

position.

4. Press the Push button once to start

charging.

• The display shows the percentage left in the power pack.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

USING THE DC POWER SUPPLY

SELECT THE VOLTAGE

1. Set the ON/OFF switch to the ON

position.

2. Press the push button repeatly

until the required voltage is shown

in blue on the top of the display.

• Select from 12V, 16V, or 19 V.

CONNECTIONS

1. Insert the yellow tip of the small fly

lead into the power pack.

2. Fit the required connector from

the selection to the other end of

the fly lead.

3. Insert the connector into the

device you want to power.

• The display shows the

percentage left in the power

pack.

USB ADAPTOR LEAD

This lead can be used to charge mobile phones and various USB devices.

1. Insert the lead into the USB socket

on the power pack.

2. Connect one of the connectors

on the lead to your device

• Do not connect more than one

connector at a time.

• This will supply a maximum of

2.1A at 5V.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

JUMP STARTING

CONNECTING THE SMART CABLE TO THE POWER PACK

1. Lift the rubber plug and insert the

jumpstart leads into the power

pack.

• The red & green LEDs will flash

alternatively.

CONNECT THE JUMP START LEADS TO THE BATTERY

1. Connect the red clamp to the unearthed battery terminal first, (this is

usually the positive (+ve) terminal and painted RED).

2. Connect the black clamp to the earthed battery terminal, (this is usually

the negative (-ve) terminal and painted BLACK)

• LED show solid green: Reasdy to start

• LED flashes red and green: Means the smart cable is in search mode,

to activate turn the ignition on (ACC)

• LED shows solid red: indicates a failed connection, possible faults

are:

WARNING: IT IS POSSIBLE THAT SOME ELECTRONIC EQUIPMENT COULD BE

DAMAGED BY JUMP STARTING. ALWAYS CHECK WITH THE VEHICLE

HANDBOOK TO DETERMINE IF ANY PRECAUTIONS SHOULD BE TAKEN.

Jump starter does not

have enough power

Check the power level of the jump starter and

charge if required.

Short Circuit Make sure that the positive & negative leads are

not touching, remove them & restart.

Reverse Polarity Make sure that the smart cable clamps are

connected correctly to the car battery, remove

them & restart.

Over Heating Wait for a few minutes & try again.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

JUMPSTART THE BATTERY

ALWAYS carry out the following preliminary checks:

• Switch off the vehicle ignition and ALL ancillary equipment (lighting,

radio etc.)

• Ensure the vehicle battery is rated at 12V and is not damaged in any

way.

• Ensure the area is well ventilated.

• Make sure that the power pack has at least 30% charge.

1. Switch the ignition to ‘start’, for NO MORE than 6 seconds. If the engine

does not start within this time, SWITCH OFF the ignition and wait for at least

3 minutes before trying again.

2. Once the engine is running, disconnect the BLACK clamp FIRST, then

disconnect the RED clamp.

MAINTENANCE

CLEANING

• Wipe the body of the unit clean using a soft damp cloth.

• Do not use abrasives to clean this product.

REPAIRS

• All repairs must be carried out by qualified service technicians.

STORAGE

• When not in use, store in a safe dry place.

CAUTION: MAKE SURE THAT THE POWER PACK IS AT LEAST 30% CHARGED

BEFORE YOU ATTEMPT TO JUMPSTART.

Inhaltsverzeichnis

Andere Clarke Zubehör Handbücher

Clarke

Clarke SG1 Bedienungsanleitung

Beliebte Zubehör Handbücher anderer Marken

Hillco

Hillco 2810 Bedienungsanleitung

Siemens

Siemens QSA2700D Bedienerhandbuch

Contours

Contours ZY024 Bedienungsanleitung

Saivod

Saivod VS621 Bedienungsanleitung

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Bedienungsanleitung

Z-Wave

Z-Wave HSD-200Z Bedienungsanleitung

turck

turck FMX-IM-2UPLI63FX Bedienungsanleitung

Decagon Devices

Decagon Devices 10HS Bedienungsanleitung

UPPAbaby

UPPAbaby Cup Holder Bedienungsanleitung

Elko

Elko SmartSensor Leakage Wireless Bedienungsanleitung

Grizzly

Grizzly H8371 Bedienungsanleitung

Panasonic

Panasonic HG-T Series Bedienungsanleitung

IFM Electronic

IFM Electronic Efector 250 Series Referenzhandbuch

Virtuox

Virtuox VirtuCLEAN 2.0 Bedienungsanleitung

DigiDesign

DigiDesign 888/24 I/O Bedienungsanleitung

PROZIS

PROZIS QUAY Bedienungsanleitung

patagonia

patagonia PSI Vest Bedienungsanleitung

SFC Energy

SFC Energy EFOY GO! Bedienungsanleitung