Clarke IBC40 Bedienungsanleitung

OPERATION & MAINTENANCE

INSTRUCTIONS

ORIGINAL INSTRUCTIONS GC1020 - ISS 2

INTELLIGENT BATTERY

CHARGER/MAINTAINER

MODEL NO: IBC40

PART NO: 6267014

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

INTRODUCTION

Thank you for purchasing this CLARKE Battery Charger / Maintainer.

Before use, read this manual thoroughly and follow all instructions given.

1. The IBC40 is designed for charging all types of 12V lead-acid and 24V lead-

acid batteries, including WET (Flooded), MF (Maintenance-Free), EFB

(Enhanced Flooded Battery), GEL, AGM (Absorbed Glass Mat) batteries.

2. A built-in intelligent microprocessor makes charging faster, easier and safer.

3. This charger has safety features, including protection for reverse polarity,

short circuit, overheat and overcharge.

GUARANTEE

This CLARKE product is guaranteed against faulty manufacture for a period of

12 months from the date of purchase. Please keep your receipt as proof of

purchase.

This guarantee is invalid if the product is found to have been abused or

tampered with in any way, or not used for the purpose for which it was

intended.

Faulty goods should be returned to their place of purchase, no product can

be returned to us without prior permission.

This guarantee does not effect your statutory rights.

ENVIRONMENTAL RECYCLING POLICY

Through purchase of this product, the customer is taking on the

obligation to deal with the WEEE in accordance with the WEEE

regulations in relation to the treatment, recycling & recovery and

environmentally sound disposal of the WEEE.

In effect, this means that this product must not be disposed of with general

household waste. It must be disposed of according to the laws governing

Waste Electrical and Electronic Equipment (WEEE) at a recognised disposal

facility.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

SAFETY INSTRUCTIONS

SAFETY PRECAUTIONS FOR WORKING IN THE VICINITY OF A BATTERY

1. If battery electrolyte contacts skin or clothing, wash immediately with soap

and water. If electrolyte enters your eye, immediately flood the eye with

running clean cold water for at least 15 minutes and get medical attention

immediately.

2. Clean the battery terminals before they are connected to the charger. Be

careful to keep corrosion from coming into contact with your eyes.

3. Batteries generate explosive gases during normal operation. Use in a well-

ventilated area.

4. Consider having someone close enough or within the range of your voice

to come to your aid when you work near a battery.

5. DO NOT smoke, strike a match, or cause a spark in vicinity of a battery or

engine. Avoid explosive gas, flames and sparks.

6. Remove all rings, bracelets, necklaces, and watches while working with a

vehicle battery. These items may produce a short-circuit that could cause

severe burns.

7. Be extra cautious to reduce risk of dropping a metal tool onto the battery.

It might spark or short-circuit a battery or other electrical hardware which

may cause an explosion or fire.

8. Study all battery manufacturer's specific precautions such as removing or

not removing cell caps while charging and recommended rates of

charge.

9. When it is necessary to remove a battery from a vehicle to charge it,

always remove the grounded terminal from the battery first. Make sure all

accessories in the vehicle are off.

10. It is NOT intended to supply power to an extra-low-voltage electrical

system or to charge dry-cell batteries. Charging dry-cell batteries may burst

and cause injury to persons and property.

11. NEVER charge a frozen, damaged, leaking or non-rechargeable battery.

WARNING: WEAR EYE PROTECTION, HAND AND CLOTHING PROTECTION.

AVOID TOUCHING EYES WHILE WORKING WITH A BATTERY. SEE YOUR

LOCAL CLARKE DEALER FOR ALL YOUR PPE REQUIREMENTS.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

SAFETY PRECAUTIONS FOR USING THE CHARGER

1. NEVER place the charger in the engine compartment or near moving parts

or near the battery; place as far away from them as the clamp leads allow.

2. DO NOT cover the charger while charging.

3. DO NOT expose to rain or wet conditions.

4. Use of an attachment not recommended or sold by the manufacturer may

result in a risk of fire, electric shock or injury to persons.

5. DO NOT overcharge batteries by selecting the wrong charge mode.

6. To reduce the risk of damage to the electric plug and lead, pull by the plug

rather than the lead when disconnecting the charger.

7. Operate with caution if the charger has received a impact/blow or been

dropped. Have it checked and repaired if damaged.

8. Any repair must be carried out by the manufacturer or an authorized

CLARKE repair agent in order to avoid danger.

CHARGER LOCATION

1. Place the charger as far away from the battery as possible.

2. DO NOT position the charger above the battery during the charging

procedure. Gases from the battery will corrode and damage the charger.

3. DO NOT let battery acid drip on the charger when reading a hydrometer

for specific gravity or when you fill the battery.

4. DO NOT use the charger in an enclosed space with reduced airflow.

SAFETY SYMBOLS

WARNING: ALWAYS SWITCH OFF THE CHARGER WHEN CONNECTING OR

DISCONNECTING LEADS.

Wear eye protection Wear protective

clothing

Wear protective gloves

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

ELECTRICAL CONNECTIONS

Before switching the product on, make sure that the voltage of your electricity supply is

the same as that indicated on the rating plate. This product is designed to operate on

230VAC 50Hz. Connecting it to any other power source may cause damage.

This product may be fitted with a non-rewireable plug. If it is necessary to change the

fuse in the plug, the fuse cover must be refitted. If the fuse cover becomes lost or

damaged, the plug must not be used until a suitable replacement is obtained.

If the plug has to be changed because it is not suitable for your socket, or due to

damage, it should be cut off and a replacement fitted, following the wiring instructions

shown below. The old plug must be disposed of safely, as insertion into a mains socket

could cause an electrical hazard.

If the colours of the wires in the power cable of this product do not correspond with the

markings on the terminals of your plug, proceed as follows.

•TheBlue wire must be connected to the terminal marked Nor coloured Black.

•TheBrown wire must be connected to the terminal marked Lor coloured Red.

We strongly recommend that this machine is connected to the mains supply

via a Residual Current Device (RCD)

If in any doubt, consult a qualified electrician. DO NOT attempt any repairs

yourself.

This symbol indicates that this is a Class II product, and does not require

an earth connection.

WARNING! READ THESE ELECTRICAL SAFETY INSTRUCTIONS

THOROUGHLY BEFORE CONNECTING THE PRODUCT TO THE

MAINS SUPPLY.

WARNING! THE WIRES IN THE POWER CABLE OF THIS PRODUCT

ARE COLOURED IN ACCORDANCE WITH THE FOLLOWING CODE:

Blue = Neutral Brown = Live

Plug must be BS1363/A approved.

Always fit a 5 Amp fuse.

Ensure that the outer sheath of the cable is firmly held by the clamp

Neutral

(Blue)

Live

(Brown)

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

THE CHARGING PROCESS

STEP 1: DIAGNOSIS

Check if the battery has connected with the charger and also check the

battery voltage.

STEP 2: DESULPHATION

If battery voltage is too low, the program automatically generates a pulsing

current to remove sulphate.

STEP 3: ANALYSE

Check if the battery voltage reaches to the minimum threshold after

desulphation, and charging begins if the battery voltage is OK.

STEP 4: SOFT START

Charge with stepped constant current.

STEP 5: BULK

Charge with constant maximum current until the battery voltage has reached

the threshold.

STEP 6: ABSORPTION

Provide gradually declining current charge for maximum battery voltage.

STEP 7: ANALYSE

Test if the battery can hold charge

STEP 8: MAINTENANCE

Continuously monitor the battery, and charging current will intelligently adapt

to the variable battery voltage. (pulse form protection).

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

OVERVIEW

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

CONNECTING TO THE BATTERY

1. Identify the polarity of battery posts. The positive battery terminal is

typically marked by these letters or symbol (POS,P,+). The negative battery

terminal is typically marked by these letters or symbol (NEG,N,-).

2. DO NOT make any connections to the carburetor, fuel lines, or thin metal

parts.

3. Identify if you have a negative or positive grounded vehicle. This can be

done by identifying which battery post (NEG or POS) is connected to the

chassis.

•FOR A NEGATIVE GROUNDED VEHICLE (MOST COMMON): connect the

RED POSITIVE clamp first to the positive battery terminal, then connect

the BLACK NEGATIVE clamp to the negative battery terminal or vehicle

chassis.

•FOR A POSITIVE GROUNDED VEHICLE (VERY UNCOMMON): connect the

BLACK NEGATIVE clamp first to the negative battery terminal, then

connect the RED POSITIVE clamp to the positive battery terminal or

vehicle chassis.

4. When disconnecting, disconnect in the reverse sequence, removing the

negative first (or positive first for positive ground systems).

CHARGING MODESS

CAUTION: A MARINE (BOAT) BATTERY MUST BE REMOVED AND

CHARGED ON SHORE. TO CHARGE IT ON BOARD REQUIRES EQUIPMENT

SPECIALLY DESIGNED FOR MARINE USE.

SELECT MODE FOR BATTERY SIZE (AH)

12V 5A 10 - 150Ah

12V 10A 40 - 300Ah

12V 20A 60 - 500Ah

12V 40A 120 - 500Ah

24V 5A 10 - 150Ah

24V 10A 40 - 300Ah

24V 20A 60 - 220Ah

12V 40A BOOST Any Capacity

12V ALTERNATOR CHECK Any Capacity

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

OPERATION

1. Connect the battery as described on page 8.

2. Plug in the mains plug and switch it on.

3. The charger will automatically detect the battery voltage (12V or 24V).

4. After 10 seconds the charger will begin charging the battery using the

following mode 12V/5A or 24V/5A.

• The user can manually select charging voltage / current modes by

pressing the "VOLTAGE" or “CURRENT” button within the first 10 seconds

after switching on (a countdown is shown on the LCD).

NOTE: If you choose 24V Mode(s) for 12V battery, the 12V battery will be

damaged

• Once the battery type has been selected successfully and charging is

started, you must disconnect the AC plug and plug in again if you want

to change the battery type mode of the charger.

• During charging, the display will show voltage (12V or 24V) and

charging current alternately.

• When the "VOLTAGE" button is pressed, the display shows battery

voltage (e.g. 12.1 V) .

5. During charging, pressing the "CHARGE" button will cause the charger to

turn off.

• The charger will be restarted by pressing "CHARGE" button again.

6. Battery level is indicated by the "battery level icon". When the battery is

fully charged, the charger will automatically switch from full charge to

maintenance status without overcharging or damaging the battery.

BATTERY LEVEL INDICATOR

LEVEL ICON EXPLANATION LEVEL ICON EXPLANATION

The 25% bar will slowly flash

when the battery level is less

than 25%. When 25% is

reached, the bar will be

solid.

The 50% bar will slowly flash

when the battery level is less

than 50%. When 50% is

reached, the bar will be solid.

The 75% bar will slowly flash

when the battery level is less

than 75%. When 75% is

reached, the bar will be

solid.

The 100% bar will slowly flash

when the battery level is less

than 100%. When 100% is

reached, the bar will be solid.

Meanwhile the maintenance

charging is activated.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

ADVANCED CHARGING MODES

The following modes are advanced charging modes that require your full

attention before selecting.

USING 12V BOOST

1. Connect the charger to the battery as shown on page 7 and switch on at

the mains power supply.

2. Allow the charger to start charging after an initial 10 second wait.

3. Press the BOOST/QUICK CHARGE button to start the boost charge mode

• For optimum results, allow boost to complete its 5-minute charge cycle.

• After 5 minutes the display will show

“000”, and you are ready to start your

vehicle.

• After each boost, the charger has a

mandatory 5-minute rest for safety

reasons (even if you press the BOOST/

QUICK CHARGE button again, the

charger will not work).

• After cooling, the LCD shows “End”

4. Press any button to enter the normal

charging mode, or the charger will

automatically enter the normal

charging mode after 10 minutes.

5. If unsuccessful when starting your

vehicle, let the battery rest for 15

minutes and try boost again. Most

vehicles will start with one boost.

6. Using 12V ALTERNATOR CHECK

WARNING: DO NOT USE BOOST MORE THAN TWO TIMES IN A 24-HOUR

PERIOD. IF TWO BOOSTS CANNOT SUCCESSFULLY START YOUR VEHICLE,

HAVE YOUR BATTERY REPLACED OR EVALUATED BY A LOCAL BATTERY

STORE.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Clarke Akkuladegerät Handbücher

Clarke

Clarke IBC20 Bedienungsanleitung

Clarke

Clarke IBC4 Bedienungsanleitung

Clarke

Clarke IBC7 Bedienungsanleitung

Clarke

Clarke Start-N-Charge BC120C Bedienungsanleitung

Clarke

Clarke Start-N-charge BC120N Bedienungsanleitung

Clarke

Clarke Start-N-Charge BC260N Bedienungsanleitung

Clarke

Clarke WIBC250 Bedienungsanleitung

Clarke

Clarke CBO9-12 Bedienungsanleitung

Clarke

Clarke IBC50 Bedienungsanleitung

Clarke

Clarke Start'N'Charge BC250 Bedienungsanleitung

Clarke

Clarke IBC80 Bedienungsanleitung

Clarke

Clarke Start n charge BC260N Handbuch

Clarke

Clarke WBC400 Bedienungsanleitung

Clarke

Clarke Start-N-Charge BC120C Bedienungsanleitung

Clarke

Clarke BC 700 Handbuch

Clarke

Clarke Start-N-Charge BC420N Installations- und Betriebshandbuch

Clarke

Clarke Start-N-Charge BC130 Bedienungsanleitung

Clarke

Clarke HFBC12-24 Bedienungsanleitung

Clarke

Clarke Start'N'Charge BC185N Bedienungsanleitung

Clarke

Clarke IBC5 Bedienungsanleitung

Clarke

Clarke ATC12VB Bedienungsanleitung

Clarke

Clarke Start-N-Charge BC150 Bedienungsanleitung

Clarke

Clarke ZX-R Pro Series Bedienungsanleitung

Clarke

Clarke IBC25 Bedienungsanleitung

Beliebte Akkuladegerät Handbücher anderer Marken

AA Portable Power Corp

AA Portable Power Corp Universal Smart Charger Bedienungsanleitung

Enelion

Enelion Vertica Bedienungsanleitung

RCA

RCA CHU6 Bedienungsanleitung

ANSMANN

ANSMANN ALCT 6/24-10 Bedienungsanleitung

Hitachi

Hitachi UC 18YRSL Fehlerbehebungshandbuch

Olympus

Olympus B-20 LPC Bedienungsanleitung

Exibel

Exibel ZH1708143 Bedienungsanleitung

Lenmar

Lenmar Mach 1 Bedienungsanleitung

CTEK

CTEK MXS 5.0 Bedienungsanleitung

ABB

ABB HT842379 Bedienungsanleitung

Nitecore

Nitecore Superb Charger SC4 Bedienungsanleitung

Renogy

Renogy RBC2125DS-21W Bedienungsanleitung

Braun

Braun BWC02M Bedienungsanleitung

CTEK

CTEK MXS 3.6 Bedienungsanleitung

Black & Decker

Black & Decker BDV090 Bedienungsanleitung

Trinity

Trinity DPD Bedienungsanleitung

Hulkman

Hulkman Sigma 1 Bedienungsanleitung

IKEA

IKEA koppla Bedienungsanleitung